Ford Explorer Service Bulletins (2026)
46 manufacturer communications on file.
- August 5, 2026•Document ID: 11036107Service Bulletin/Repair InstructionsVEHICLE SPEED CONTROL; ELECTRICAL SYSTEM; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL
- Mfr Comm. #:
- SSM 55071
- Date Added:
- August 11, 2026
- Manufacturer:
- FORD
SummarySome 2025-2026 Aviator/Explorer/Expedition/F-150/Mustang Mach-E/Navigator vehicles may exhibit the hands-free BlueCruise feature intermittently/consistently unavailable when BlueCruise is active and when traveling in a "Blue Zone". Speed sign recognition may also be inaccurate. If there are no active relevant diagnostic trouble codes (DTC) present and the issue persists after multiple key cycles and if the BlueCruise System Health Check passes, download and run the "TCU - Reset Telematics Control Unit (TCU) Module" application using the latest software level of the Ford Diagnosis and Repair System (FDRS). If the condition is resolved, inform customers that this may be a temporary fix and engineering is currently working on a solution expected in Q4 2026. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. For claiming, use causal 14G229 and labor operations 12651D and 12651D4. If the condition persists after a test drive, refer to Workshop Manual (WSM), Section 419-03B for normal diagnosti
Associated Products (12)Associated Documents - August 4, 2026•Document ID: 11035581Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; VISIBILITY/WIPER; STRUCTURE:BODY
- Mfr Comm. #:
- SSM 55060
- Date Added:
- August 4, 2026
- Manufacturer:
- FORD
SummarySome 2024-2026 Explorer vehicles built on or before 27-Feb-2026 and equipped with the panoramic glass roof may exhibit an uneven gap at the front edge of the roof opening panel shield when fully closed. The gap is an appearance issue only, but may allow outside light to pass through the opening. A new gap hider seal has been released to correct this condition (service part number SB5Z-7851884-A). Adjustment or replacement of the glass, shade or headliner assembly is not necessary. The new seal is installed directly onto the existing vertical flange that is present and visible at the front of the opening when the shade is opened. Once installed, the front edge of the shade will press against the new seal when fully closed. To install, center the seal in the opening with the flexible material facing the power shade and press the seal u-channel over the vertical flange. Explorer vehicles built on or after 27-Feb-2026 have the seal already installed and can be referenced if necessary. Once the seal is installed, perform the shield/shade initialization procedure in Workshop Manual (WSM), Section 501-05 > Gen
Associated Products (3)Associated Documents - August 3, 2026•Document ID: 11035556Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; UNKNOWN OR OTHER; FUEL/PROPULSION SYSTEM; POWER TRAIN
- Mfr Comm. #:
- SSM55059
- Date Added:
- August 3, 2026
- Manufacturer:
- FORD
SummarySome 2021-2023 F-150 vehicles equipped with a 3.5L PowerBoost engine, 2020-2026 Explorer vehicles equipped with a 3.3L hybrid engine, and 2020-2023 Lincoln Aviator vehicles equipped with a 3.0L EcoBoost hybrid engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). The vehicle may be unable to enter electric-only drive modes as expected during normal drive cycles. This may be due to the belt integrated starter generator (BISG). For vehicles with this condition, follow the necessary Pinpoint Test in Workshop Manual (WSM), Section 303-06 for DTC P0A1E and repair the vehicle as directed. Note that previous replacement of the BISG does not negate the need for subsequent BISG replacements if directed to do so by the appropriate Pinpoint Test diagnostics. Engineering is investigating this BISG quality concern. Monitor PTS for updates regarding this investigation.
Associated Products (12)Associated Documents - July 23, 2026•Document ID: 11035269Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; UNKNOWN OR OTHER; FUEL/PROPULSION SYSTEM
- Mfr Comm. #:
- SSM 55031
- Date Added:
- July 28, 2026
- Manufacturer:
- FORD
SummarySome 2021-2026 Ford/Lincoln vehicles may exhibit various symptoms including but not limited to the auto start/stop system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration
Associated Products (61)2026 Ford Bronco2026 Ford Bronco Sport2026 Ford Escape2026 Ford Expedition2026 Ford Explorer2026 Ford F-1502026 Ford Maverick2026 Ford Mustang2026 Ford Ranger2026 Ford Transit2026 Lincoln Aviator2026 Lincoln Corsair2026 Lincoln Nautilus2026 Lincoln Navigator2025 Ford Bronco2025 Ford Bronco Sport2025 Ford Escape2025 Ford Expedition2025 Ford Explorer2025 Ford F-150+ 41 moreAssociated Documents - July 8, 2026•Document ID: 11034968Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; ENGINE; UNKNOWN OR OTHER
- Mfr Comm. #:
- TSB 26-2269
- Date Added:
- July 13, 2026
- Manufacturer:
- FORD
SummarySome of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0300 and/or P0316 stored in the powertrain control module (PCM) (with no other relevant DTCs present) during a cold start after a 3 to 8 hours cold soak. This may be due to the machining surface of the intake ports in the cylinder head.
Associated Products (4)Associated Documents - June 30, 2026•Document ID: 11034225Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; STEERING
- Mfr Comm. #:
- TSB 26-2302
- Date Added:
- July 1, 2026
- Manufacturer:
- FORD
SummaryThis bulletin supersedes 26-2150. Reason for update: To remove the M6 nut from the part list and remove the Steps to install the M6 nut from the Service Procedure. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * "Steering Assist Fault Service Required" message displayed in the instrument panel cluster (IPC) * Reduced steering assist * Diagnostic trouble codes (DTCs) U3008:1B and/or U3009:1B stored in the power steering control module (PSCM) This may be due to the PSCM ground connections.
Associated Products (4)Associated Documents - June 18, 2026•Document ID: 11034036Service Bulletin/Repair InstructionsFUEL/PROPULSION SYSTEM; UNKNOWN OR OTHER; POWER TRAIN
- Mfr Comm. #:
- SSM 54948
- Date Added:
- June 24, 2026
- Manufacturer:
- FORD
SummarySome 2025-2026 Explorer/Aviator/Police Interceptor Utility non-hybrid vehicles built on 06-Feb-2025 and through 13-Dec-2025 may exhibit various drivability symptoms including a rough idle or hesitation shortly after refueling. These symptoms may also be accompanied by liquid fuel in the fuel vapor lines and fuel vapor canister as well as an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0133, P0300, P0301, P0302, P0303, P0304, P0305, and/or P0306 stored in the powertrain control module (PCM). This condition may be due to an intermittently sticking fuel level vent valve on the fuel tank allowing fuel to enter the evaporative emissions system lines and evaporative emissions canister during refueling. If the customer states that the drivability symptoms occurred after recently filling the vehicle, replace the fuel tank (9002) and evaporative emissions canister (9D653). Refer to Workshop Manual (WSM), Section 310-01 to replace the fuel tank. Refer to WSM, Section 303-13 to replace the evaporative emission canister. For claiming use causal part 9002 and labor operations 90
Associated Products (4)Associated Documents - June 5, 2026•Document ID: 11033775Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- SSM 54902
- Date Added:
- June 9, 2026
- Manufacturer:
- FORD
SummaryFor 20202026 vehicles equipped with the 10R60 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. Workshop Manual (WSM) updates related to this diagnostic procedure are planned for release in Q4 2026. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification for transmission replacement.
Associated Products (21)2026 Ford Bronco2026 Ford Explorer2026 Ford Ranger2026 Lincoln Aviator2025 Ford Bronco2025 Ford Explorer2025 Ford Ranger2025 Lincoln Aviator2024 Ford Bronco2024 Ford Explorer2024 Ford Ranger2024 Lincoln Aviator2023 Ford Bronco2023 Ford Explorer2023 Lincoln Aviator2022 Ford Bronco2022 Ford Explorer2022 Lincoln Aviator2021 Ford Bronco2021 Ford Explorer+ 1 moreAssociated Documents - May 30, 2026•Document ID: 11033575Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- TSB 26-2263
- Date Added:
- June 5, 2026
- Manufacturer:
- LINCOLN
SummaryThis bulletin supersedes 26-2112. Reason For Update: add 2026 model year vehicles, update LV fluid XT-10-QLVC and CXT-10-LV6 description to add "Transfer Case Fluid 4WD Only", and update Step 4 to inspect/replace 7H351 and 7B177 outside of this article. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated MIL with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
Associated Products (18)2026 Ford Expedition2026 Ford Explorer2026 Ford F-1502026 Ford Mustang2026 Ford Transit2026 Lincoln Navigator2025 Ford Expedition2025 Ford Explorer2025 Ford F-1502025 Ford Mustang2025 Ford Transit2025 Lincoln Navigator2024 Ford Expedition2024 Ford Explorer2024 Ford F-1502024 Ford Mustang2024 Ford Transit2024 Lincoln NavigatorAssociated Documents - May 29, 2026•Document ID: 11033260Service Bulletin/Repair InstructionsSTRUCTURE:BODY; ELECTRICAL SYSTEM
- Mfr Comm. #:
- SSM 54882
- Date Added:
- June 3, 2026
- Manufacturer:
- FORD
SummarySome 2025-2026 Explorer/Aviator vehicles may exhibit a no crank/no start/discharged battery condition with diagnostic trouble codes (DTC) B144D:29, B144E:29, B1555:29, B1556:29 and/or U3003:16 stored in the rear gate trunk module (RGTM). The power liftgate may also be inoperative. This may be due to water intrusion into the left and/or right power liftgate motors caused by a loose grommet on the electrical harness at the body pass-through. To correct this condition, install a new power liftgate motor corresponding to the DTC(s) set in the RGTM (B144D:29/B144E:29 Ýleft¨ or B1555:29/B1556:29 Ýright¨). To prevent water intrusion into the new liftgate motor, make sure the grommet on the new motor is seated properly by pushing on the grommet at the body pass-through until it clicks into place. For claiming, use causal part 14B351 (Explorer) or 14B350 (Aviator) and labor operations 12651D and 14350AL (left) or 14350AR (right) or 14350AT (both) <br /><br /> If a vehicle with this concern exhibits water intrusion, corrosion, or unseated grommets in or around the liftgate motor, submit a Global Concern Report
Associated Products (4)Associated Documents - May 28, 2026•Document ID: 11033579OtherPOWER TRAIN
- Mfr Comm. #:
- 26B12
- Date Added:
- June 5, 2026
- Manufacturer:
- FORD
SummaryCertain 2026 Model Year Aviator, Explorer and Bronco Vehicles with 10R60 Transmissions: Transmission and Fluid Cooler Replacement
Associated Products (3)Associated Documents - May 21, 2026•Document ID: 11032924Service Bulletin/Repair InstructionsFUEL/PROPULSION SYSTEM
- Mfr Comm. #:
- SSM 54857
- Date Added:
- May 26, 2026
- Manufacturer:
- FORD
Summary2020-2026 Explorer/Escape/Corsair, 2021-2026 Bronco Sport/Bronco, 2022-2026 Maverick, 2024-2026 Mustang/Ranger/Nautilus vehicles equipped with a 2.0L or 2.3L EcoBoost engine may require removal of the turbocharger wastegate control actuator linkage for various reasons. The Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls - Turbocharger - 2.0L/2.3L EcoBoost > Removal and Installation > Wastegate Control Actuator Linkage service procedure been added. In addition, the wastegate actuator rod (9E408), associated retention springs (9342) and retaining clips (00817) have been released as lower-level components to complete the repair without replacing the entire turbocharger wastegate actuator assembly.
Associated Products (35)2026 Ford Bronco2026 Ford Bronco Sport2026 Ford Escape2026 Ford Explorer2026 Ford Maverick2026 Ford Mustang2026 Ford Ranger2025 Ford Bronco2025 Ford Bronco Sport2025 Ford Escape2025 Ford Explorer2025 Ford Maverick2025 Ford Mustang2025 Ford Ranger2024 Ford Bronco2024 Ford Bronco Sport2024 Ford Escape2024 Ford Explorer2024 Ford Maverick2024 Ford Mustang+ 15 moreAssociated Documents - May 16, 2026•Document ID: 11032762Service Bulletin/Repair InstructionsSTRUCTURE:BODY; VISIBILITY/WIPER
- Mfr Comm. #:
- SSM 54829
- Date Added:
- May 19, 2026
- Manufacturer:
- FORD
SummarySome 2024-2026 Nautilus and 2025-2026 Explorer/Aviator vehicles equipped with power autofold exterior mirrors may exhibit concerns with the passenger mirror not automatically folding in or out at times, while the driver side mirror automatically folds properly. This may be due to the software in the driver door module (DDM) and passenger door module (PDM). To correct the condition, reprogram the DDM and PDM using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 14B291 and labor operation MT14B291SSM up to 0.4 hours.
Associated Products (7)Associated Documents - May 15, 2026•Document ID: 11032760Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- SSM 54827
- Date Added:
- May 19, 2026
- Manufacturer:
- LINCOLN
SummarySome 2020-2026 Explorer/Police Interceptor Utility/Aviator vehicles may require replacement of the front drive halfshaft inner/outer CV joint boot for various reasons. If Workshop Manual (WSM), Section 205-04 > Diagnosis and Testing leads to CV joint boot replacement, L1MZ-3A331-G (Explorer/Police Interceptor Utility front inner/outer CV joint boot kit), L1MZ-3A331-H (Aviator front inner/outer CV joint boot kit), L1MZ-3A331-F (Explorer/Police Interceptor Utility front inner CV joint boot kit) and L1MZ-3A331-E (Aviator front inner CV joint boot kit) have been released for service. Refer to WSM, Section 205-04 for Removal and Installation procedures.
Associated Products (12)Associated Documents - May 7, 2026•Document ID: 11032693Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; UNKNOWN OR OTHER
- Mfr Comm. #:
- TSB 26-2185
- Date Added:
- May 14, 2026
- Manufacturer:
- FORD
SummaryThis bulletin supersedes 25-2621. Reason for update: add 2026 model year vehicles and Transit, update the causal part number (15604), update the Service Procedure, update the service labor operations for 2023 F-Super Duty, and add service labor operations for Transit. Some vehicles listed in the Model statement above may exhibit a no crank/no start condition where the customer cannot start their vehicle. The vehicle may also exhibit a "No Key Detected" message displayed on the instrument panel cluster (IPC), and no key fob works in the back up slot. The remote keyless entry (RKE) functionality will work to lock/unlock the vehicle.
Associated Products (23)2026 Ford Bronco2026 Ford Expedition2026 Ford Explorer2026 Ford F-1502026 Ford Mustang2026 Ford Ranger2026 Lincoln Aviator2026 Lincoln Nautilus2026 Lincoln Navigator2025 Ford Bronco2025 Ford Expedition2025 Ford Explorer2025 Ford F-1502025 Ford Mustang2025 Ford Ranger2025 Lincoln Aviator2025 Lincoln Nautilus2025 Lincoln Navigator2024 Ford Bronco2024 Ford F-150+ 3 moreAssociated Documents - May 5, 2026•Document ID: 11033578OtherPOWER TRAIN
- Mfr Comm. #:
- 26B08
- Date Added:
- June 5, 2026
- Manufacturer:
- LINCOLN
SummaryCertain 2025 Bronco/Ranger and 2025-2026 Explorer/Aviator 4-wheel drive vehicles equipped with a 10R60 transmission. Transmission Replacement
Associated Products (6)Associated Documents - May 5, 2026•Document ID: 11032685Service Bulletin/Repair InstructionsSTRUCTURE:BODY; ELECTRICAL SYSTEM
- Mfr Comm. #:
- SSM 54800
- Date Added:
- May 14, 2026
- Manufacturer:
- LINCOLN
SummarySome 2025-2026 Explorer/Aviator and 2026 Expedition/Navigator vehicles may exhibit an intermittent inoperative remote start feature using either the key fobs or the Ford/Lincoln App. This may be due to the software in the body control module (BCM). After replicating the concern, use the Ford Diagnosis and Repair System (FDRS) to monitor the RMTSTRT_F_ARB_LST and RMTSTRT_F_TRGT_NM parameter identification (PIDS) in the BCM. If both PID values show "true" in any of the last 5 saved values, engineering is currently working on a solution for this condition that is expected in Q4 2026. Schedule service appointments for customers once the repair becomes available. If either of the BCM PID values do not show "true" in any of the saved values, refer to Workshop Manual (WSM), Section 501-14 Handles, Locks, Latches, Entry Systems > Diagnosis and Testing > Locks, Latches and Entry Systems > Pinpoint Test R (Explorer/Aviator)/Pinpoint Test V (Expedition/Navigator) for normal diagnostics and repair as necessary outside of this article. For claiming, use causal part 15604 and labor operations 12651D and 12651D45
Associated Products (6)Associated Documents - May 4, 2026•Document ID: 11032565Service Bulletin/Repair InstructionsENGINE; ELECTRICAL SYSTEM; POWER TRAIN
- Mfr Comm. #:
- SSM 54795
- Date Added:
- May 8, 2026
- Manufacturer:
- FORD
SummarySome 2021-2023 F-150 vehicles equipped with a 3.5L PowerBoost engine and 2020-2026 Explorer vehicles equipped with a 3.3L hybrid engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). The vehicle may be unable to enter electric-only drive modes as expected during normal drive cycles. This may be due to the software within the belt integrated starter generator (BISG). For vehicles with this condition, follow Pinpoint Test I: Battery Isolation/Voltage Stabilization Control Circuit Carry Outance located in the Workshop Manual (WSM), Section 303-06D and repair the vehicle as necessary. Note that the BISG is on backorder status at the time of this publication and Ford is working to make parts available. Engineering is investigating this concern. Monitor PTS for updates.
Associated Products (9)Associated Documents - April 30, 2026•Document ID: 11032248Service Bulletin/Repair InstructionsPOWER TRAIN; ELECTRICAL SYSTEM
- Mfr Comm. #:
- SSM 54792
- Date Added:
- May 5, 2026
- Manufacturer:
- FORD
SummarySome 2025-2026 Explorer vehicles equipped with a 2.3L EcoBoost engine and built on 16-Aug-2025 and through 5-Mar-2026 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0335 stored in the powertrain control module (PCM). DTC P033F may also be stored in the PCM. This may be due to a pin fit concern at PCM connector C1381E pin 7. To correct this condition, install a new terminal in wiring harness connector C1381E pin 7 (GN/BN) using terminal repair kit DU2Z-14474-CA. Refer to Wiring Diagram, Cell 5 for wiring repair information. For claiming use causal part 12A581 and labor operations 12650D and 12650D45WR.
Associated Products (2)Associated Documents - April 29, 2026•Document ID: 11032247Service Bulletin/Repair InstructionsFUEL/PROPULSION SYSTEM
- Mfr Comm. #:
- SSM 54787
- Date Added:
- May 5, 2026
- Manufacturer:
- LINCOLN
SummarySome 2020-2023 Aviator and 2025-2026 Explorer/Police Interceptor Utility hybrid vehicles may exhibit a "Refuel Error See Manual" message in the instrument panel cluster (IPC) after installing a replacement fuel filler door assembly (7827936). This may be due to a concern with the replacement fuel filler door assembly. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and Ford is currently working on a solution for this condition that is expected Q3 2026. Further replacement of the fuel filler door assembly will not resolve this condition at this time. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.<br /><br /> If a customer vehicle exhibits this concern, submit a Vehicle Concern Report. To submit a report, click on the "Submit Global Concern Report (GCR)" link at the upper right of the PTS Vehicle ID screen (vehicle identification number ÝVIN¨ required) a
Associated Products (5)Associated Documents