Ram 3500 Complaints
2,367 consumer complaints on file.
- #11658458May 2, 2025SERVICE BRAKES
The contact owns a 2024 Ram 3500. The contact stated that while driving at an undisclosed speed, the brake pedal was depressed, and the ABS warning light illuminated. The contact forcefully depressed the brake pedal to stop the vehicle. The vehicle was taken to the dealer, where it was diagnosed that the ABS module had failed and needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 96,000. The VIN was not available.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11657841April 30, 2025ENGINE AND ENGINE COOLING
The contact owns a 2022 Ram 3500. The contact stated while driving 40-45 MPH and hauling a 14-ft loaded trailer, the engine made an abnormally loud knocking sound. The check engine warning light was illuminated. The contact was able to pull over to the side of the road. The vehicle failed to restart and was towed to the residence, where a mobile independent mechanic diagnosed that the grid heater nut had melted and entered cylinder #6. The vehicle was then towed to the dealer, where it was diagnosed that the grid heater nut failure had caused catastrophic failure of the pistons, turbo charger, and engine. The dealer determined that the engine assembly needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and informed the contact that the repair could not be covered under warranty due to the mileage on the vehicle. The failure mileage was approximately 112,700.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11657073April 27, 2025POWER TRAIN, ELECTRICAL SYSTEM
Radio some time turns off by it's self. Transmission has locked up in park after driving and put in park ,and will not go into any other gear, unless truck is turned off. After turning truck back on it will engage into preferred gear. It has done this for few time since February.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11655691April 20, 2025ENGINE
The turbo actuator quit working at 103,000 miles. Loss of power. Took to Dodge dealer in Bartlesville Oklahoma to fix. I bought an extended warranty but it wouldn’t cover the cost because I have a flatbed. Out $7,500. I noticed they recalled this part on the 2015 and they need to on the 2018.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11654914April 16, 2025FUEL/PROPULSION SYSTEM
Def pump failed, I had to have it replaced before it degraded my travel speed to 5 mph. After spending $250 to Dodge dealer in Oxnard Service department for them to tell me exactly what it said on the truck code DEF pump needed replacing, I decided I didn't want to spend an extra $1000 for the dealer to fix it ($3900 they wanted for this job). On 11/16/22, I paid ($2865.81) to a reputable diesel mechanic to replace the pump. I was denied the reimbursement that was promised in the recall information. I need help with this! I pay $1200/ month for truck and insurance, but Ram can't reimburse me for a recall I paid out of pocket for, as promised. ABSOLUTE CROOKS! I want help with this. I see there are multiple other complaints of the same issue! HELP!
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11654966April 16, 2025SERVICE BRAKES, HYDRAULIC
The contact owns a 2018 Ram 3500. The contact stated while driving at an undisclosed speed, the electronic stability control and traction control systems warning light illuminated. The contact received notification of NHTSA Campaign Number: 24V896000 (Service Brakes, Hydraulic); however, the part to do the recall repair was unavailable. The vehicle was taken to the dealer but was not diagnosed or repaired. The dealer confirmed that parts were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The failure mileage was approximately 95,000. VIN tool confirms parts not available.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11655098April 16, 2025SERVICE BRAKES
ABS PUMP Failed on 09/03/22. ABS light constantly coming on and off and dinging had it repaired on 10/21/22 had to wait for part, was charged 930.00 ABS FAILED 2ND TIME ABS Light constantly going on and off and dinging ON 1/31/25, Received recall C4B/NHTSA 24-896 on 01/13/25 in mail. Ferman Dodge of new port Richey refused to cover it, and their recall center refused to cover it or reimburse me. I had it replaced a second time on 4/11/25 had to wait for the part to come in. They are not honoring the recall which has been under investigation by NHTSA since 2021. So, I have been charged 2 time, another 957.00 and the second time the truck had not even been driven 30000 miles since last repair. So, every 30 to 40 thousand miles the abs pump fails possibly causing the brakes to malfunction. They are also saying that it was repaired on 12/05/25, Truck was not in for service on that date, see attachments,
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11654493April 14, 2025SERVICE BRAKES, HYDRAULIC
The contact owns a 2018 Ram 3500. The contact received notification of NHTSA Campaign Number: 24V896000 (Service Brakes, Hydraulic). The contact stated that there were lights blinking with an abnormal buzzing sound coming from the vehicle. The contact stated that while driving at approximately 40 MPH, the brake pedal was inadvertently depressed, and the rear end shifted. The ABS warning light illuminated, and a notification warning buzzed for approximately 20 minutes. The vehicle was taken to a dealer, where the failure was linked to the unrepaired recall. The contact stated that the part for the recall repair was not yet available, but parts were ordered. The contact stated that the dealer received the parts, but the parts were incorrect. The vehicle was not yet repaired. The manufacturer was notified of the failure and advised the contact to contact the dealer to schedule the repair. The failure mileage was approximately 140,000. VIN tool confirms parts not available.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11654082April 11, 2025SERVICE BRAKES
2nd time truck has warning lights on related to ABS, electronic braking system with no parts available from manufacturer - HCU. Truck is set up to tow a gooseneck trailer. Loss of braking capacity has put me in hazardous situations as the problem is intermittent. Previous repair, where dealer stated my rotors were bad with fewer than 20k miles, was expensive and tech said it could be related to the electronic braking system failure causing rotors to malfunction. No remedy from manufacturer is unacceptable as I'm unable to use my vehicle and if I did, I could be in a situation causing a major accident with no brakes.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11653425April 8, 2025SERVICE BRAKES, HYDRAULIC
The contact owns a 2018 Ram 3500. The contact stated while driving 65 MPH, the ABS warning light illuminated. The vehicle returned to normal functionality, but the failure became a regular occurrence. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 24V896000 (Service Brakes, Hydraulic); the VIN was included, but parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The failure mileage was 34,000. VIN tool confirms parts not available.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11653428April 8, 2025SERVICE BRAKES, HYDRAULIC
The contact owns a 2018 Ram 3500. The contact received notification of NHTSA Campaign Number: 24V896000 (SERVICE BRAKES, HYDRAULIC); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact stated that the ABS and traction control warning lights were illuminated, and the vehicle was braking erratically while driving at various speeds. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 47,000. VIN tool confirms parts not available.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11652809April 4, 2025SERVICE BRAKES
The hydraulic control unit has been on recall since December 2024, I been to the dealer several times a they told me they do not have a remedy for the problem and they do not know if or when they will have a solution for the problem. Now I have a Check engine,ABS, and the eletronic stability control light on. The deler told the lights are on due to the HCU is bad. But they did give me a solution for the repairs
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11652811April 4, 2025SEATS
Driver power seat started moving forward on its own until it was all the way forward, would not move backwards with the button. It pinned my legs to the dash, preventing me from reaching the throttle or brake pedal
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11652513April 3, 2025SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:ABS WARNING LIGHT
The contact owns a 2018 Ram 3500. The contact stated while driving 40 MPH and depressing the brake pedal, the vehicle failed to respond. The ABS and the traction control warning lights were illuminated, and a chime sounded. The contact was able to drive the vehicle to the residence. The vehicle was taken to an independent mechanic, where it was diagnosed with ABS failure. The contact stated that the vehicle was repaired under an unknown recall two years ago, and the contact was provided reimbursement for a related repair. The local dealer was contacted and confirmed that the vehicle was previously repaired under an unknown recall. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 65,100.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11652365April 2, 2025UNKNOWN OR OTHER, FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING
Firstly, I have contacted Ram about the issue and they said I can't do anything about it. It's a safety feature and it absolutely is the total OPPOSITE of a safety feature! When on icy roads, with traction control off, and in four-wheel drive, if the truck starts sliding, it cuts the power to the wheels when I need power to pull out of the slide. I've been driving in icy / snowy conditions since I was 14 years old and I'm now [XXX] . Since it cut power to the wheels, the truck continued to slide off into the ditch causing major front end damage. If there had been a person walking their dog there, they would have been killed. This happened at about 15 mph and was totally preventable if I had had control of the vehicle instead of a computer! I don't even understand what the traction control button being turned off actually does because apparently it doesn't do anything. Also, I about got thrown through the windshield when the automatic brakes came on thinking I was going to rear-end some one who was not going to be there by the time I got there! Again, not a safety feature! There definitely needs to be a way to turn these systems off completely. If I remove the fuse for the traction control system it unfortunately affects other systems as well. So that is not an acceptable fix. In my opinion, people are putting far too much trust in computer systems. I do not believe there should be a computer in control of a vehicle at any time. You will never get me in a" "self-driving car!" It's complete lunacy! INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Crash:
- Yes
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11652016April 1, 2025SERVICE BRAKES, HYDRAULIC
The contact owns a 2018 Ram 3500. The contact stated while his neighbor was driving the vehicle at an undisclosed speed, the cruise control disengaged unintendedly. The ABS warning light and the traction control warning light were illuminated. Additionally, the contact stated that the failure had recurred while driving 65 MPH and while driving at various speeds. The vehicle was taken to the dealer, where it was diagnosed that the HCU had failed and needed to be replaced; however, the part was on a national backorder. The vehicle was not repaired. The contact stated that the failure persisted while driving. The contact later received notification of NHTSA Campaign Number: 24V896000 (Service Brakes, Hydraulic); however, the part to do the recall repair was not yet available. The local dealer was contacted. The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the failure through email. The failure mileage was approximately 6,500.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11652119April 1, 2025UNKNOWN OR OTHER
I am writing to report an ongoing issue with my 2016 Ram 3500 (V6), related to Safety Recall V06 (NHTSA 19V-021) for the drag link, which was performed in 2020 before I purchased the vehicle two years ago. The recall "fix" involved welding the adjustable nuts on the steering linkage, rendering it non-adjustable. Since then, I have been unable to get a proper front-end alignment at any service shop. Multiple mechanics have refused to perform an alignment because the welded drag link cannot be adjusted, and they’ve stated it compromises the vehicle's steering integrity and tire wear. This is a significant safety concern. Without the ability to align the front end, the vehicle’s handling is affected, potentially leading to uneven tire wear, reduced control, or worse, a steering-related failure. I’ve contacted dealerships and Chrysler (FCA US LLC), but they insist the recall was completed and offer no further remedy, despite the fact that this weld does not allow for standard maintenance. New Ram 3500s off the assembly line come with adjustable drag links, not welded ones, which proves this was a poor fix for a safety issue. I urge the NHTSA to revisit this recall and require Chrysler to replace the defective drag link with a proper, adjustable component, rather than leaving owners like me with a substandard repair that hinders basic vehicle maintenance and safety. I purchased this truck in good faith, but this unresolved issue has made it a liability. Please investigate and address this matter before it leads to more serious consequences.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11651843March 31, 2025SERVICE BRAKES, HYDRAULIC
The contact owns a 2017 Ram 3500. The contact received notification of NHTSA Campaign Number: 24V896000 (SERVICE BRAKES, HYDRAULIC); however, the part to do the recall repair was unavailable. The local dealer was contacted, and it was confirmed that parts were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11651599March 30, 2025SERVICE BRAKES, POWER TRAIN, VEHICLE SPEED CONTROL
Vehicle displayed warnings: Service Antilock Brakes Service Electronic Stability Control Service Trailer Brake System The truck has only 4,650 miles on it. When this happens, the above systems do not work along with the 4 wheel drive system. When towing a heavy trailer, the loss of trailer brakes can easily cause an accident due to jackknifing of the trailer and greatly increased stopping distance. Loosing 4 wheel drive in snow or mud can cause an accident or getting stuck.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11651250March 28, 2025SERVICE BRAKES, FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING
Related to the known HCU failure on these vehicles. My first submitted complaint was on Oct 22, 2022 and this issue is still not resolved. I received a letter in mail on January 21st of this year stating that a recall was finally underway. Now it's late March and everyone's standard response is "No Remedy Yet". The remedy is actually installing HCU part number 68143491AB which replaces the corrupt factory installed part 6814391AA. These parts are readily available online so why can't factory service centers begin replacing these failed HCU's. This complaint is filed due to my belief that this dangerous safety issue is not being resolved in a reasonable, timely manner. Not even close.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0