Jeep Wagoneer S Service Bulletins
298 manufacturer communications on file.
- April 30, 2025•Document ID: 11018064Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 08-078-25 REV. A
- Date Added:
- May 7, 2025
- Manufacturer:
- JEEP
Summary"RSU With Additional Sleep Cycles for HV Battery Integrity Check - Flash: Motor Control Processor A (MCP A) Updates 11A1 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● P1626-00 - Park Pawl Motor Stuck. Customers may also comment on one or more of the following: ● Wrench lamp on in the Instrument Panel Cluster (IPC). ● Not able to move the shifter out of Park. ● Vehicle has reduced power. This bulletin also includes the following software enhancement: ● Software enhancement to prevent erroneous fault identification resulting in inverter shutdown This bulletin involves reprogramming the **IDCM,** BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine."
Associated Products (1)Associated Documents - April 30, 2025•Document ID: 11018047Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 08-128-25
- Date Added:
- May 7, 2025
- Manufacturer:
- JEEP
Summary"Flash: Battery Pack Control Module (BPCM) Updates 6A1 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more the following Diagnostic Trouble Codes (DTCs): ● P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE - Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA - Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 - Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1 Performance. ● P0F01 - Hybrid/EV Battery Module 2 Performance. ● P0F02 - Hybrid/EV Battery Module 3 Performance. ● P0F03 - Hybrid/EV Battery Module 4 Performance. ● P0F04 - Hybrid/EV Battery Module 5 Performance. ● P0F05 - Hybrid/EV Battery Module 6 Performance. ● P0F06 - Hybrid/EV Battery Module 7 Performance. ● P0F07 - Hybrid/EV Battery Module 8 Performance. ● P0F08 - Hybrid/EV Battery Module 9 Performance. ● P0F09 - Hybrid/EV Battery Module 10 Performance. ● P0F0A - Hybrid/EV Battery Module 11 Performance. ● P0F0B - Hybrid/EV Battery Module 12 Performance. ● P0F0C - Hybrid/EV Battery Module 13 Performance. Customers may experience the following: ● The wrench icon displays on the Instrument Panel Cluster (IPC) This bulletin involves reprogramming the IDCM, BPCM and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine."
Associated Products (1)Associated Documents - April 30, 2025•Document ID: 11017969Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 08-129-25 REV. A
- Date Added:
- May 6, 2025
- Manufacturer:
- JEEP
Summary"Flash: Integrated Dual Charging Module (IDCM) Updates 11A1 Customers may comment on one or more of the following: ● 12 volt battery lamp on the Instrument Panel Cluster (IPC) illuminated due to depleted 12 volt battery. ● Unable to charge at High Voltage Charging station at Level-1, Level-2 or DC Fast Charge. This bulletin involves reprogramming the IDCM, BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine."
Associated Products (1)Associated Documents - April 30, 2025•Document ID: 11017940Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 08-013-25 REV. C
- Date Added:
- May 6, 2025
- Manufacturer:
- JEEP
Summary"Flash: Motor Control Processor B (MCP B) Updates 11A1 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● P1626-00 - Park Pawl Motor Stuck. Customers may also comment on one or more of the following: ● Wrench lamp on in the Instrument Panel Cluster (IPC). ● Not able to move the shifter out of Park. ● Vehicle has reduced power. This bulletin also includes the following software enhancement: ● Software enhancement to prevent erroneous fault identification resulting in inverter shutdown. This bulletin involves reprogramming the IDCM, BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine. "
Associated Products (1)Associated Documents - April 29, 2025•Document ID: 11018108Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 08-129-25
- Date Added:
- May 7, 2025
- Manufacturer:
- JEEP
Summary"Flash: Integrated Dual Charging Module (IDCM) Updates 11A1 Customers may comment on one or more of the following: ● 12 volt battery lamp on the Instrument Panel Cluster (IPC) illuminated due to depleted 12 volt battery. ● Unable to charge at High Voltage Charging station at Level-1, Level-2 or DC Fast Charge. This bulletin involves reprogramming the IDCM, BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine."
Associated Products (1)Associated Documents - April 29, 2025•Document ID: 11018097Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 08-010-25 REV. C
- Date Added:
- May 7, 2025
- Manufacturer:
- JEEP
Summary"Flash: Motor Control Processor A (MCP A) Updates 11A1 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● P1626-00 - Park Pawl Motor Stuck. Customers may also comment on one or more of the following: ● Wrench lamp on in the Instrument Panel Cluster (IPC). ● Not able to move the shifter out of Park. ● Vehicle has reduced power. This bulletin also includes the following software enhancement: ● Software enhancement to prevent erroneous fault identification resulting in inverter shutdown. This bulletin involves reprogramming the BPCM, MCP A, MCP B and the EVCU with the latest available software and then performing a Wheel End Disconnect Position Learn routine"
Associated Products (1)Associated Documents - April 29, 2025•Document ID: 11018096Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 08-011-25 REV. B
- Date Added:
- May 7, 2025
- Manufacturer:
- JEEP
Summary"Flash: Battery Pack Control Module (BPCM) Updates 11A1 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE – Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA – Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 – Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1 Performance. ● P0F01 - Hybrid/EV Battery Module 2 Performance. ● P0F02 - Hybrid/EV Battery Module 3 Performance. ● P0F03 - Hybrid/EV Battery Module 4 Performance. ● P0F04 - Hybrid/EV Battery Module 5 Performance. ● P0F05 - Hybrid/EV Battery Module 6 Performance. ● P0F06 - Hybrid/EV Battery Module 7 Performance. ● P0F07 - Hybrid/EV Battery Module 8 Performance. ● P0F08 - Hybrid/EV Battery Module 9 Performance. ● P0F09 - Hybrid/EV Battery Module 10 Performance. ● P0F0A - Hybrid/EV Battery Module 11 Performance. ● P0F0B - Hybrid/EV Battery Module 12 Performance. ● P0F0C - Hybrid/EV Battery Module 13 Performance.** ● P0CA6-00 - Hybrid/EV Battery Charging Current High. NOTE: If the following DTCs are present/active in the BPCM, Battery Pack replacement will be required. Guided Diagnostics will prompt you for the repair action if the diagnostic is present on the vehicle. ● P0ADB-00 - Hybrid/EV Battery Positive Contractor A Control Circuit Low. ● P0AE2-00 - Hybrid/EV Battery Precharge Contactor Circuit Stuck Closed. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor ""A"" Stuck Closed. ● P0FF8-00 - Hybrid/EV Battery Precharge Contactor Circuit ""B"" Stuck Closed. Customers may also comment on one or more of the following: ● Wrench icon is illuminated on the Instrument Panel Cluster (IPC). ● Vehicle will not enter Drive Ready Mode. This bulletin also includes the following software enhancement: ● Bootloader update to prevent battery disconnect unit damage. ● Improvements in detecting pre-existing battery disconnect unit damage. ● Charging related enhancements that may lead to DTC P0CA6 falsely setting This bulletin involves reprogramming the **IDCM,** BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine"
Associated Products (1)Associated Documents - April 29, 2025•Document ID: 11018095Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 08-013-25 REV. B
- Date Added:
- May 7, 2025
- Manufacturer:
- JEEP
Summary"Flash: Motor Control Processor B (MCP B) Updates 11A1 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● P1626-00 - Park Pawl Motor Stuck. Customers may also comment on one or more of the following: ● Wrench lamp on in the Instrument Panel Cluster (IPC). ● Not able to move the shifter out of Park. ● Vehicle has reduced power. This bulletin also includes the following software enhancement: ● Software enhancement to prevent erroneous fault identification resulting in inverter shutdown. This bulletin involves reprogramming the **IDCM,** BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine."
Associated Products (1)Associated Documents - April 29, 2025•Document ID: 11018094Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 08-014-25 REV. B
- Date Added:
- May 7, 2025
- Manufacturer:
- JEEP
Summary"Flash: Electronic Vehicle Control Unit (EVCU) Updates 11A1 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● C10F8-00 - Left Front Wheel Hub Disconnect Actuator Position Sensor Circuit Range/Performance. ● C10F9-00 - Right Front Wheel Hub Disconnect Actuator Position Sensor Circuit Range/Performance. ● P061B-00 - Internal Control Module Torque Calculation Performance. Customers may also comment on one or more of the following: ● **Instrument Panel Cluster (IPC), radio range and charge time estimations and messages are not correct. ● Battery range incorrect. ● Improved battery State of Charge (SoC) accuracy in off-nominal conditions. ● Battery heating values incorrect on radio when on Performance Pages display. ● Charging does not start when plugged in. ● Charging is not indicating when battery is at full charge. ● Charging slow or takes too long. ● Bumps and jerks while accelerating or decelerating.** ● Wrench icon is illuminated on the IPC. ● Turtle icon is illuminated on the IPC. ● Vehicle enters into limp home mode. **In addition, the following software enhancement is also available: ● Enables compatibility with the Flo V3 Chargers.** This bulletin involves reprogramming the **IDCM,** BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine"
Associated Products (1)Associated Documents - April 29, 2025•Document ID: 11018050Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 08-127-25
- Date Added:
- May 7, 2025
- Manufacturer:
- JEEP
Summary"Flash: Electronic Vehicle Control Unit (EVCU) Updates 6A1 Custome rs may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● C10F8-00 - Left Front Wheel Hub Disconnect Actuator Position Sensor Circuit Range/Performance. ● C10F9-00 - Right Front Wheel Hub Disconnect Actuator Position Sensor Circuit Range/Performance. ● P061B-00 - Internal Control Module Torque Calculation Performance. Customers may also comment on one or more of the following: ● Instrument Panel Cluster (IPC), radio range and charge time estimations and messages are not correct. ● Battery range incorrect. ● Improved battery State of Charge (SoC) accuracy in off-nominal conditions. ● Battery heating values incorrect on radio when on Performance Pages display. ● Charging does not start when plugged in. ● Charging is not indicating when battery is at full charge. ● Charging slow or takes too long. ● Bumps and jerks while accelerating or decelerating. ● Wrench icon is illuminated on the IPC. ● Turtle icon is illuminated on the IPC. ● Vehicle enters into limp home mode. In addition, the following software enhancement is also available: ● Enables compatibility with the Flo V3 Chargers. This bulletin involves reprogramming the IDCM, BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine"
Associated Products (1)Associated Documents - April 29, 2025•Document ID: 11018035Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 08-132-25
- Date Added:
- May 6, 2025
- Manufacturer:
- JEEP
Summary"Flash: Integrated Dual Charging Module (IDCM) Updates 6A1 Customers may comment on one or more of the following: ● 12 volt battery lamp on the Instrument Panel Cluster (IPC) illuminated due to depleted 12 volt battery. ● Unable to charge at High Voltage Charging station at Level-1, Level-2 or DC Fast Charg This bulletin involves reprogramming the IDCM, BPCM and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine."
Associated Products (1)Associated Documents - April 29, 2025•Document ID: 11018023Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 08-134-25
- Date Added:
- May 6, 2025
- Manufacturer:
- JEEP
Summary"Flash: Integrated Dual Charging Module (IDCM) Updates 6A1 Customers may comment on one or more of the following: ● 12 volt battery lamp on the Instrument Panel Cluster (IPC) illuminated due to depleted 12 volt battery. ● Unable to charge at High Voltage Charging station at Level-1, Level-2 or DC Fast Charg This bulletin involves reprogramming the IDCM, BPCM and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine."
Associated Products (1)Associated Documents - April 28, 2025•Document ID: 11018194Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 08-076-25 REV.A
- Date Added:
- May 8, 2025
- Manufacturer:
- JEEP
Summary"RSU With Additional Sleep Cycles for HV Battery Integrity Check - Flash: Battery Pack Control Module (BPCM) Updates 11A1 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE – Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA – Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 – Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1 Performance. ● P0F01 - Hybrid/EV Battery Module 2 Performance. ● P0F02 - Hybrid/EV Battery Module 3 Performance. ● P0F03 - Hybrid/EV Battery Module 4 Performance. ● P0F04 - Hybrid/EV Battery Module 5 Performance. ● P0F05 - Hybrid/EV Battery Module 6 Performance. ● P0F06 - Hybrid/EV Battery Module 7 Performance. ● P0F07 - Hybrid/EV Battery Module 8 Performance. ● P0F08 - Hybrid/EV Battery Module 9 Performance. ● P0F09 - Hybrid/EV Battery Module 10 Performance. ● P0F0A - Hybrid/EV Battery Module 11 Performance. ● P0F0B - Hybrid/EV Battery Module 12 Performance. ● P0F0C - Hybrid/EV Battery Module 13 Performance.** ● P0CA6-00 - Hybrid/EV Battery Charging Current High. NOTE: If the following DTCs are present/active in the BPCM, Battery Pack replacement will be required. Guided Diagnostics will prompt you for the repair action if the diagnostic is present on the vehicle. ● P0ADB-00 - Hybrid/EV Battery Positive Contractor A Control Circuit Low. ● P0AE2-00 - Hybrid/EV Battery Precharge Contactor Circuit Stuck Closed. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor ""A"" Stuck Closed. ● P0FF8-00 - Hybrid/EV Battery Precharge Contactor Circuit ""B"" Stuck Closed. Customers may also comment on one or more of the following: ● Wrench icon is illuminated on the Instrument Panel Cluster (IPC). ● Vehicle will not enter Drive Ready Mode. his bulletin also includes the following software enhancement:● Bootloader update to prevent battery disconnect unit damage. ● Improvements in detecting pre-existing battery disconnect unit damage. ● Charging related enhancements that may lead to DTC P0CA6 falsely setting. " "RSU With Additional Sleep Cycles for HV Battery Integrity Check - Flash: Battery Pack Control Module (BPCM) Updates 11A1 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE – Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA – Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 – Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1 Performance. ● P0F01 - Hybrid/EV Battery Module 2 Performance. ● P0F02 - Hybrid/EV Battery Module 3 Performance. ● P0F03 - Hybrid/EV Battery Module 4 Performance. ● P0F04 - Hybrid/EV Battery Module 5 Performance. ● P0F05 - Hybrid/EV Battery Module 6 Performance. ● P0F06 - Hybrid/EV Battery Module 7 Performance. ● P0F07 - Hybrid/EV Battery Module 8 Performance. ● P0F08 - Hybrid/EV Battery Module 9 Performance. ● P0F09 - Hybrid/EV Battery Module 10 Performance. ● P0F0A - Hybrid/EV Battery Module 11 Performance. ● P0F0B - Hybrid/EV Battery Module 12 Performance. ● P0F0C - Hybrid/EV Battery Module 13 Performance.** ● P0CA6-00 - Hybrid/EV Battery Charging Current High. NOTE: If the following DTCs are present/active in the BPCM, Battery Pack replacement will be required. Guided Diagnostics will prompt you for the repair action if the diagnostic is present on the vehicle. ● P0ADB-00 - Hybrid/EV Battery Positive Contractor A Control Circuit Low. ● P0AE2-00 - Hybrid/EV Battery Precharge Contactor Circuit Stuck Closed. ● P0AA1-00 - Hybrid/EV Battery Positiv
Associated Products (1)Associated Documents - April 26, 2025•Document ID: 11017355Service Bulletin/Repair InstructionsSTRUCTURE:BODY; ELECTRICAL SYSTEM
- Mfr Comm. #:
- S2308000120 REV.C
- Date Added:
- April 30, 2025
- Manufacturer:
- RAM
SummaryRain Sensing Auto Wipers and Auto on Head Lamps Inoperative
Associated Products (33)2025 Dodge Charger2025 Jeep Compass2025 Jeep Grand Cherokee2025 Jeep Grand Cherokee L2025 Jeep Grand Wagoneer2025 Jeep Wagoneer2025 Jeep Wagoneer S2025 Ram 15002025 Ram 35002025 Ram 45002025 Ram 55002024 Dodge Charger2024 Jeep Compass2024 Jeep Grand Cherokee2024 Jeep Grand Cherokee L2024 Jeep Grand Wagoneer2024 Jeep Wagoneer2024 Jeep Wagoneer S2024 Ram 15002024 Ram 2500+ 13 moreAssociated Documents - April 24, 2025•Document ID: 11017175Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; SERVICE BRAKES
- Mfr Comm. #:
- 9100567
- Date Added:
- April 24, 2025
- Manufacturer:
- JEEP
Summary"ELECTRIC PARK BRAKE ACTUATOR WHEN REPLACING ELECTRIC PARK BRAKE ACTUATOR (EPB) PLEASE REPLACE ENTIRE CALIPER UNIT (CALIPER AND EPB ACTUATOR) AND RETURN ENTIRE UNIT FOR ENGINEERING ANALYSIS."
Associated Products (1)Associated Documents - April 18, 2025•Document ID: 11017126Service Bulletin/Repair InstructionsSTRUCTURE:BODY
- Mfr Comm. #:
- S2523000030
- Date Added:
- April 22, 2025
- Manufacturer:
- JEEP
SummaryFender To Fascia Flush And Or Gap Adjustment.
Associated Products (2)Associated Documents - April 18, 2025•Document ID: 11017125Service Bulletin/Repair InstructionsUNKNOWN OR OTHER
- Mfr Comm. #:
- S2523000029
- Date Added:
- April 22, 2025
- Manufacturer:
- JEEP
SummaryFront Footwell Wet. Water On Floor At A Pillar. Front Carpet Wet.
Associated Products (2)Associated Documents - April 17, 2025•Document ID: 11017092Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- S258A000013
- Date Added:
- April 17, 2025
- Manufacturer:
- CHRYSLER
SummaryAM Radio Static, With No Active or Stored Radio Antenna Diagnostic Trouble Codes (DTC).
Associated Products (27)2025 Chrysler Pacifica2025 Chrysler Voyager2025 Dodge Charger2025 Jeep Grand Cherokee2025 Jeep Grand Cherokee L2025 Jeep Wagoneer S2025 Jeep Wrangler2024 Chrysler Pacifica2024 Chrysler Voyager2024 Dodge Charger2024 Jeep Grand Cherokee2024 Jeep Grand Cherokee L2024 Jeep Wagoneer S2024 Jeep Wrangler2023 Chrysler Pacifica2023 Chrysler Voyager2023 Jeep Grand Cherokee2023 Jeep Grand Cherokee L2023 Jeep Wrangler2022 Chrysler Pacifica+ 7 moreAssociated Documents - April 15, 2025•Document ID: 11017068Service Bulletin/Repair InstructionsUNKNOWN OR OTHER
- Mfr Comm. #:
- S2524000003
- Date Added:
- April 16, 2025
- Manufacturer:
- JEEP
SummaryCustomer Indicates Flutter Noise Heard From Dash
Associated Products (1)Associated Documents - April 11, 2025•Document ID: 11017017Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL; FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING
- Mfr Comm. #:
- 08-114-25
- Date Added:
- April 15, 2025
- Manufacturer:
- JEEP
Summary"Front Collision Prevention Warning On Customer may experience the following: ● 'Forward Collision Disabled/Service Automatic Emergency Braking' warning lights on in Instrument Panel Cluster (IPC). ● Both Adaptive Cruise Control (ACC) and Front Impact Braking are inoperative. This bulletin involves replacing the Front Long Range Radar."
Associated Products (1)Associated Documents