Nissan Rogue Service Bulletins
837 manufacturer communications on file.
- May 22, 2014•Document ID: 10192373Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; STRUCTURE
- Mfr Comm. #:
- NTB14047
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummaryIF YOU CONFIRM: The "front door power window and door lock/unlock switch (RH) finisher" (switch finisher) has a loose fit, causting an excessive gap. See Figure 1. ACTION: 1. Remove the passenger front door finisher (door finisher). - Refer to the Electronic Service Manual (ESM), section INT-Interior, for removal procedure. 2. Install a foam block where shown in SERVICE PROCEDURE. - Use the foam block listed in PARTS INFORMATION. 3. Install the door finisher with a new switch finisher listed in PARTS INFORMATION. - Refer to the ESM, section INT-Interior, for installation procedure. See this bulletin for further detail.
Associated Products (1)Associated Documents - May 6, 2014•Document ID: 10192361Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ELECTRICAL SYSTEM
- Mfr Comm. #:
- NTB14038
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummarySERVICE INFORMATION When registering the Intelligent Keys (I-Keys) to a vehicle for one of the following concerns: * After replacing the BCM. Or * When one of the I-Keys has been lost and needs to be replaced. Or * When additional I-Keys are being added to the vehicle. Always use the following steps to insure proper registration of the I-Keys: 1. First Initialize the BCM. 2. Register all of the vehicle?s ?previously registered? I-Keys to the vehicle first. And then 3. Register any new (additional) I-Keys only after all of the pre-existing I-Keys have been registered. 4. Confirm operations of all I-Keys. Please see this bulletiln for further details.
Associated Products (5)Associated Documents - April 29, 2014•Document ID: 10192354Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:WIRING
- Mfr Comm. #:
- NTB14032
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummarySERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Nissan vehicles has changed. This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.
Associated Products (138)2017 Nissan 370Z2017 Nissan Altima2017 Nissan Armada2017 Nissan Frontier2017 Nissan GT-R2017 Nissan Juke2017 Nissan Leaf2017 Nissan Maxima2017 Nissan Murano2017 Nissan NV2002017 Nissan Pathfinder2017 Nissan Rogue2017 Nissan Sentra2017 Nissan Titan2017 Nissan Versa2016 Nissan 370Z2016 Nissan Altima2016 Nissan Frontier2016 Nissan GT-R2016 Nissan Juke+ 118 moreAssociated Documents - April 9, 2014•Document ID: 10192348Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- NTB14026
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummaryIF YOU CONFIRM: An electrical issue caused by corrosion in the Main Harness to Body Harness connectors located at the bottom of the driver side A-pillar: Connector numbers M13 to B3 and/or M14 to B4. ACTIONS: 1. Preform repairs to harness connectors as needed. 2. Apply Harness Protector to cover the harness connectors. See this bulletin for further detail.
Associated Products (7)Associated Documents - April 9, 2014•Document ID: 10055490Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- NTB-14-026
- Date Added:
- June 4, 2014
- Manufacturer:
- NISSAN
SummaryNISSAN: THE MAIN HARNESS TO BODY HARNESS CONNECTORS IS EXPERIENCING ELECTRICAL CORROSION ISSUES. 2008-2014 ROGUE. *PE
Associated Products (7)Associated Documents - April 4, 2014•Document ID: 10192344Service Bulletin/Repair InstructionsSTEERING; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
- Mfr Comm. #:
- NTB14021
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummaryIF YOU CONFIRM The Instrument Lower Panel LH (as shown in Figure 1) molded plastic clip will not stay secured. ACTION Install a shim between the Steering Member and the Instrument Panel and apply felt tape to the Instrument Lower Panel LH with the SERVICE PROCEDURE starting on page 2. Please see this bulletin for further details.
Associated Products (1)Associated Documents - March 27, 2014•Document ID: 10192341Service Bulletin/Repair InstructionsWHEELS; EQUIPMENT
- Mfr Comm. #:
- PC274
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummaryNissan is conducting a Dealer Inventory Inspection to inspect the right front and right rear lug nuts on 372 certain specific 2014 Nissan Rogue and Pathfinder vehicles currently in dealer inventory.
Associated Products (2)Associated Documents - March 26, 2014•Document ID: 10192339Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT
- Mfr Comm. #:
- PC266
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummaryNissan is conducting a customer satisfaction action on certain MY2014 Nissan Rogue SL AWD vehicles to send customers a Cargo Protector accessory that was inadvertently listed on the Monroney label but was not installed.
Associated Products (1)Associated Documents - March 21, 2014•Document ID: 10192337Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
- Mfr Comm. #:
- PC266OL
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummaryNissan is conducting a customer satisfaction action on certain MY2014 Nissan Rogue SL AWD vehicles to send customers a Cargo Protector accessory that was inadvertently listed on the Monroney label but was not installed.
Associated Products (1)Associated Documents - March 21, 2014•Document ID: 10192336Service Bulletin/Repair InstructionsPOWER TRAIN:AUTOMATIC TRANSMISSION
- Mfr Comm. #:
- NTB14019
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummaryIF YOU CONFIRM The MIL is on with any one of these DTCs alone, or any combination of any of DTCs: * P2765 - CLUTCH B SPEED SENSOR * P0500 - VEH SPEED SEN/CIRC * P1574 - ASCD VHL SPD SEN * P1715 - INPUT SPEED SENSOR * P0720 - VEH SPD SEN/CIR And * Moisture and/or corrosion is present on or around the Secondary Speed Sensor pins. ACTION a. Remove the moisture from the Harness connector with CRC QD (or equivalent) electric cleaner. b. Replace Secondary Speed Sensor shown in Figure 1. Please see this bulletin for further details.
Associated Products (1)Associated Documents - March 20, 2014•Document ID: 10192335Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM
- Mfr Comm. #:
- NTB14018
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummaryIF YOU CONFIRM A rattle coming from the exhaust center tube heat shield, and a heat shield spot weld is detached, ACTION Install a band clamp around the heat shield and over the detached spot weld. See this bulletin for further detail.
Associated Products (7)Associated Documents - March 7, 2014•Document ID: 10192330Service Bulletin/Repair InstructionsEQUIPMENT; STEERING
- Mfr Comm. #:
- PC268A
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummaryOn a very small percentage of vehicles, the steering column bolt may need to be replaced by the dealership. Nissan is placing the vehicles that have not had the inspection performed on a Quality Hold.
Associated Products (2)Associated Documents - March 5, 2014•Document ID: 10054095Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- NTB-13-106
- Date Added:
- December 20, 2013
- Manufacturer:
- NISSAN
SummaryNISSAN: IGNITION MUST CYCLE TWO TIMES TO COMPLETE CONFIGURATION FOR NAVIGATION EQUIPPED VEHICLES AND IF CONFIGURATION NOT COMPLETED SOME SYMPTOMS MAY OCCUR (NO BACK UP CAMERA, NO VOLUME RESPONSE, EQUALIZER ADJUSTED SO BASS CONTROL IS AT MAXIMUM, NO STEERING WHEEL SWITCH RESPONSE). MODEL 2014 ALTIMA, ROGUE, FRONTIER, SENTRA, XTERRA. *PE UPDATED 02/26/2014 *JS UPDATED 4/22/14. *PE
Associated Products (5)Associated Documents - February 26, 2014•Document ID: 10192329Service Bulletin/Repair InstructionsSTEERING; EQUIPMENT
- Mfr Comm. #:
- PC267
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummaryNissan is conducting a Dealer Service Action to inspect and, if necessary, replace the steering knuckle on certain specific 2014 Nissan Rogue vehicles currently in inventory.
Associated Products (1)Associated Documents - February 20, 2014•Document ID: 10192327Service Bulletin/Repair InstructionsSTEERING
- Mfr Comm. #:
- PC268
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummaryNissan is conducting a Dealer Service Action to inspect the steering column bolt on certain specific 2014 Nissan Leaf and Rogue vehicles currently in dealer inventory only.
Associated Products (2)Associated Documents - January 27, 2014•Document ID: 10192305Service Bulletin/Repair InstructionsEQUIPMENT; AIR BAGS
- Mfr Comm. #:
- NTB08055C
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummarySERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
Associated Products (257)2015 Nissan GT-R2014 Nissan 370Z2014 Nissan Altima2014 Nissan Armada2014 Nissan Cube2014 Nissan Frontier2014 Nissan GT-R2014 Nissan Juke2014 Nissan Leaf2014 Nissan Maxima2014 Nissan Murano2014 Nissan NV2014 Nissan NV2002014 Nissan Pathfinder2014 Nissan Quest2014 Nissan Rogue2014 Nissan Sentra2014 Nissan Titan2014 Nissan Versa2014 Nissan Versa Note+ 237 moreAssociated Documents - January 27, 2014•Document ID: 10025522Service Bulletin/Repair InstructionsAIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVE
- Mfr Comm. #:
- NTB-08-055-A
- Date Added:
- August 16, 2008
- Manufacturer:
- NISSAN
SummaryNISSAN: SRS PRECAUTIONS DURING SERVICE;IMPROPER MAINTENANCE, INCLUDING INCORRECT REMOVAL AND INSTALLATION OF THE SRS, CAN LEAD TO A SERIOUS INJURY OR DEATH CAUSED BY UNINTENTIONAL ACTIVATION OF THE SRS ON ALL NISSAN MODELS WITH THE SRS SYSTEMS. *PE UPDATED 2/21/14. *PE
Associated Products (138)2009 Nissan Armada2009 Nissan GT-R2009 Nissan Murano2009 Nissan Titan2008 Nissan 350Z2008 Nissan Altima2008 Nissan Armada2008 Nissan Frontier2008 Nissan Maxima2008 Nissan Murano2008 Nissan Pathfinder2008 Nissan Quest2008 Nissan Rogue2008 Nissan Sentra2008 Nissan Titan2008 Nissan Versa2008 Nissan Xterra2007 Nissan 350Z2007 Nissan Altima2007 Nissan Armada+ 118 moreAssociated Documents - January 15, 2014•Document ID: 10192295Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; POWER TRAIN
- Mfr Comm. #:
- PC260
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummaryNissan is conducting a Dealer Service Action to inspect the CVT output speed sensor on certain specific 2014 Nissan Altima, Pathfinder, Rogue vehicles currently in dealer inventory only.
Associated Products (3)Associated Documents - January 13, 2014•Document ID: 10192293Service Bulletin/Repair InstructionsENGINE; ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM)
- Mfr Comm. #:
- NTB12091A
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummarySERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Nissan vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.
Associated Products (101)2015 Nissan GT-R2014 Nissan 370Z2014 Nissan Altima2014 Nissan Armada2014 Nissan Cube2014 Nissan Frontier2014 Nissan GT-R2014 Nissan Juke2014 Nissan Maxima2014 Nissan Murano2014 Nissan NV2014 Nissan NV2002014 Nissan Pathfinder2014 Nissan Quest2014 Nissan Rogue2014 Nissan Sentra2014 Nissan Titan2014 Nissan Versa2014 Nissan Versa Note2014 Nissan Xterra+ 81 moreAssociated Documents - December 11, 2013•Document ID: 10192282Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING
- Mfr Comm. #:
- NTB13107
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummarySERVICE INFORMATION Intelligent Key (I-Key) systems on the Applied Vehicles use two (2) different Radio Frequencies (RF) that are similar to other wireless devices; 315 MHz and 433 MHz. In the event another wireless device (e.g. aftermarket alarm system) is transmitting at the same time as an I-Key, it can interfere with the I-Key signals being received by the BCM. If there is interference with I-Key signals, the following symptoms may occur: - The I-key is not detected, causing: - The engine to not start (no response when the Stop/Start button is pressed) - "I-Key System Error" displayed in the instrument cluster - "No I-Key Detected" displayed in the instrument cluster - Intermittent operation of the buttons on the remote (Key FOB). - Intermittent operation of the door request switches. If a vehicle has experienced the above symptoms, or a customer has reported the above symptoms, refer to Supplemental Diagnosis / Information in this bulletin. See this bulletin for further detail.
Associated Products (5)Associated Documents