BMW X6 Service Bulletins
1,072 manufacturer communications on file.
- May 1, 2015•Document ID: 10147127Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B111614
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard."
Associated Products (56)Associated Documents - May 1, 2015•Document ID: 10147125Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B110815
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryN63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. ? B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs ? B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints ? B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity ? B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. ? Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine ? Excessive engine oil consumption ? Spark plugs fouled with engine oil
Associated Products (91)Associated Documents - May 1, 2015•Document ID: 10147123Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B070314
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryDiagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Associated Products (142)Associated Documents - May 1, 2015•Document ID: 10058427Service Bulletin/Repair InstructionsFUEL SYSTEM, OTHER:DELIVERY:FUEL PUMP
- Mfr Comm. #:
- SIB-13-02-15
- Date Added:
- September 19, 2015
- Manufacturer:
- BMW
SummaryBMW: SOME VEHICLES WILL EXPERIENCE REDUCED ENGINE OUTPUT WHEN ENGINE MALFUNCTION, DUE TO HIGH PRESSURE PUMP FAILURE OF QUANTITY CONTROL VALVE. MODEL 2011 F01,F02,F04,F07,F10,F12,F13,E70,E71,E71. *PE
Associated Products (2)Associated Documents - May 1, 2015•Document ID: 10057338Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- SIB-11-16-14
- Date Added:
- May 20, 2015
- Manufacturer:
- BMW
SummaryBMW: ON CERTAIN VEHICLES, ENGINE TIMING CHAIN SHOULD BE CHECKED FOR EARLY STAGES OF WEAR, AND A REPAIR SOLUTION SHOULD BE PROVIDED. *PE UPDATED 9/25/15. *PE UPDATED 10/6/15. *PE
Associated Products (10)Associated Documents - April 6, 2015•Document ID: 10193495Service Bulletin/Repair InstructionsVISIBILITY
- Mfr Comm. #:
- B510415
- Date Added:
- May 17, 2021
- Manufacturer:
- BMW
SummaryThe customer complains of rattling noises from the rear window when driving on rough roads.
Associated Products (50)Associated Documents - April 1, 2015•Document ID: 10152317Service Bulletin/Repair InstructionsBACK OVER PREVENTION
- Mfr Comm. #:
- B660115
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
SummarySurround View Camera Last User Mode Operation Change. After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear is selected, the default view will be the rear camera. The surround/top camera view has been removed from the last user mode function. This is to meet the upcoming (new) federal regulations regarding rear view cameras. Note: The surround/top camera view is available, but the driver must manually switch the camera view using the iDrive controller.
Associated Products (130)Associated Documents - April 1, 2015•Document ID: 10152305Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B122114
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
SummaryEngine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
Associated Products (76)Associated Documents - April 1, 2015•Document ID: 10152303Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B121015
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
SummaryN63: CBS Oil Service Conversion in ISTA/P. The CBS oil service conversion performed for the N63 Customer Car Package and timing chain check (SI B11 16 14) does not work correctly for the above models with the current version of ISTA/P. After the conversion, the forecast interval does not change to the desired 10,000 miles/12 months, or the forecast is displayed as an invalid value, for example: 25,000 miles/24 months. 1. Incorrect DME coding or calibration data, which is being investigated. 2. The ISTA CBS correction test plan contains an error when attempting to correct an invalid oil service prognosis value.
Associated Products (12)Associated Documents - April 1, 2015•Document ID: 10152301Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- B110614
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
Summary"This bulletin outlines the Customer Care Package program that has been designed exclusively for BMW vehicles with the N63 engine. Vehicles with the N63 high performance engine are engineered with EfficientDynamics that provides fuel economy without compromising on its ""class leading"" power and performance. To ensure these engines keep delivering the ultimate performance, we have designed this Care Package that includes a 6 point check, and if necessary, the replacement of one or more of the following powertrain components: ? Hot-Film Air Mass Sensors ? PIEZO High Pressure Fuel Injectors ? Engine Vacuum Pump ? Fuel System Low Pressure Sensor/Feed Line ? Fresh Air Intake Turbo Seals ? Crankcase Ventilation Lines (Hoses) Note: Due to ongoing quality control monitoring, testing of the Bosch fuel system low-pressure sensor showed that replacement of the fuel system low-pressure sensor with Index 1 is no longer required in this customer care package. Refer to the attached procedure for the applicable replacement instructions regarding the fuel system low-pressure sensor. This engine care package also includes a multi-point inspection of the vehicle, including tire pressures, fluid levels, safety and convenience features. The N63CCP is NOT a mandatory Technical Campaign or Recall (per the authorities). It should only be completed based on parts availability, workshop capacity, and the customer's schedule. Complete all other applicable open Campaigns per the DCS Warranty inquiry and the Key Reader. Perform all recommended, due or qualifying ""time-based"" maintenance service task items as directed by the Key Reader/ISPA Light application. When eligible, also perform the procedure described in SI B61 30 14: 12-Volt Battery Replacement together with performing the N63 Customer Care Package. After completing all the necessary repairs, the vehicle needs to be road tested for 30 minutes to assure the highest standard of performed repairs (Please see ""Warranty Inf
Associated Products (59)Associated Documents - April 1, 2015•Document ID: 10152298Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- B000614
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
Summary?SI B00 06 14April 2015 Maintenance and General HintsTechnical Service This Service Information bulletin supersedes SI B00 06 14 dated March 2015. designates changes to this revision SUBJECT BMW Early Warning Information Program.
Associated Products (22)Associated Documents - April 1, 2015•Document ID: 10058483Service Bulletin/Repair InstructionsFUEL SYSTEM, OTHER
- Mfr Comm. #:
- SIB-13-04-15
- Date Added:
- September 26, 2015
- Manufacturer:
- BMW
SummaryBMW: PROCEDURAL INFORMATION ON THE INSTALLATION OF FUEL SYSTEM LOW PRESSURE SENSOR AND NOT CORRECTLY INSTALLED WILL LEAD TO FAILURE OF LOW PRESSURE SENSOR AND METAL SUPPLY LINE. MODEL 2008-14. *PE
Associated Products (11)Associated Documents - April 1, 2015•Document ID: 10058467Service Bulletin/Repair InstructionsENGINE; FUEL SYSTEM, OTHER:STORAGE:FUEL GAUGE SYSTEM; ELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- SIB-12-21-14
- Date Added:
- September 25, 2015
- Manufacturer:
- BMW
SummaryBMW: FUEL GAUGE FAILS TO SHOW CORRECT LEVEL OF FUEL WHEN FILLING FUEL TANK BUT WOULD UPDATE ITSELF AFTER DRIVING AWHILE AND ILLUMINATION OF ENGINE MALFUNCTION LAMP (MIL) COMES ON, DUE TO SOFTWARE ERROR IN INSTRUMENT CLUSTER. MODEL 2011-15. *PE
Associated Products (5)Associated Documents - March 1, 2015•Document ID: 10147690Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- B840514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryOne or both of the situations listed below may be encountered: ? Android device connection stability (dropped calls) ? Third-Party App Metadata: The album art and song title do not update when streaming audio from Pandora or Spotify, etc. New KISU (Customer Initiated Software Update) software is available on the TIS website. This software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation.
Associated Products (150)Associated Documents - March 1, 2015•Document ID: 10147679Service Bulletin/Repair InstructionsSTRUCTURE:BODY:DOOR
- Mfr Comm. #:
- B511614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryBody Equipment Technical Service. This Service Information bulletin supersedes SI B51 16 14 dated January 2015 designates changes to this revision SUBJECT Door Opens to First Stage While Driving. The door opens to the first stage and the Check Control Message (CCM) is displayed. This can affect any door. Automatic soft-close drive (Bowden cable lock)
Associated Products (3)Associated Documents - March 1, 2015•Document ID: 10147669Service Bulletin/Repair InstructionsPOWER TRAIN:DRIVELINE:DRIVESHAFT
- Mfr Comm. #:
- B260114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryDriveshaft Technical Service. This Service Information bulletin supersedes SI B26 01 14 dated August 2014. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. designates changes to this revision SUBJECT Service Action: Inspect Front Driveshaft. The universal joints in the front driveshaft may wear out prematurely.
Associated Products (14)Associated Documents - March 1, 2015•Document ID: 10147660Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; EQUIPMENT; ELECTRICAL SYSTEM
- Mfr Comm. #:
- B121015
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"SI B12 10 15 Engine Electrical Systems March 2015 Technical Service This Service Information bulletin supersedes SI B12 10 15 dated January 2015. designates changes to this revision SUBJECT N63: CBS Oil Service Conversion in ISTA/P. The CBS oil service conversion performed for the N63 Customer Car Package and timing chain check (SI B11 16 14) did not work correctly with ISTA/P 3.54.x or 3.55.0. It did not change the interval to the desired 12 months/10,000 miles for the vehicles listed above in the specified production ranges. The ""Conversion, oil service 12 months/15,000 km/10,000 miles"" is working properly for all other N63 vehicles produced after these dates. Incorrect coding data in the affected ISTA/P versions"
Associated Products (35)Associated Documents - March 1, 2015•Document ID: 10147656Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B111614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard. AFFECTED VEHICLES This Service Action applies to E70, E71, E72, F01, F02, F04, F07, F10, F12, and F13 vehicles with the N63 engines corresponding to the production dates listed above. First check if a Service Action label with a code number 728 is already attached to the B-pillar. If a code number 728 has already been punched out, the Campaign has already been performed and no further action is necessary. Eligible vehicles will show the following Service Action-related Campaign Code: 00 13 48 02 00 If the vehicle already has a label from a previous Service Action/Recall Campaign, affix the new label next to the old one. Do not affix one label on top of another one, because a number from an underlying label could appear in the punched-out hole of the new label."
Associated Products (65)Associated Documents - March 1, 2015•Document ID: 10147655Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B110715
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"N63: Quality Control Monitoring After CCP. INFORMATION If the vehicle exhibits any of the above drivability issues, perform the ISTA/D N63 Misfire Detection test plan. Please make sure the FASTA data is transmitted. Submit a PuMA case titled ""N63: Drivability after CCP."" Follow the recommendations received."
Associated Products (56)Associated Documents - March 1, 2015•Document ID: 10058494Service Bulletin/Repair InstructionsLATCHES/LOCKS/LINKAGES:DOORS:LATCH; STRUCTURE:BODY:DOOR
- Mfr Comm. #:
- B-511614
- Date Added:
- September 28, 2015
- Manufacturer:
- BMW
SummaryDOOR OPENS, WHILE DRIVING, TO FIRST STAGE, CAUSING CHECK CONTROL MESSAGE TO BE DISPLAYED *CN
Associated Products (4)Associated Documents