Ford Bronco Service Bulletins (2023)
204 manufacturer communications on file.
- April 3, 2024•Document ID: 10253552Service Bulletin/Repair InstructionsUNKNOWN OR OTHER
- Mfr Comm. #:
- SSM 52410
- Date Added:
- April 24, 2024
- Manufacturer:
- FORD
SummaryVarious vehicles have had pinpoint tests, guided routines and the Warranty and Policy Manual recentlyupdated for diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.
Associated Products (55)2024 Ford Bronco2024 Ford Bronco Sport2024 Ford Edge2024 Ford Escape2024 Ford Expedition2024 Ford F-1502024 Ford Maverick2024 Ford Mustang2024 Ford Ranger2024 Ford Transit Connect2024 Lincoln Aviator2024 Lincoln Corsair2024 Lincoln Nautilus2024 Lincoln Navigator2023 Ford Bronco2023 Ford Bronco Sport2023 Ford Edge2023 Ford Escape2023 Ford Expedition2023 Ford F-150+ 35 moreAssociated Documents - March 25, 2024•Document ID: 10252616Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- TSB 24-2086
- Date Added:
- April 3, 2024
- Manufacturer:
- FORD
SummarySome 2021-2023 Bronco vehicles equiped with a 2.7L engine may exhibit an ilumintated MIL with DTC P0456 stored in the powertrain control module (PCM). This may be due to the software level of the PCM and has no effect on vehicle operation.
Associated Products (3)Associated Documents - March 20, 2024•Document ID: 10252558Service Bulletin/Repair InstructionsEQUIPMENT; STRUCTURE:BODY:ROOF AND PILLARS; STRUCTURE
- Mfr Comm. #:
- TSB 24-2080
- Date Added:
- April 3, 2024
- Manufacturer:
- FORD
SummaryThis article supersedes 23-2024 to update parts list to include rivets. Some 2021-2023 Bronco vehicles equipped with a factory soft top roof may exhibit a headliner that is detaching from the soft top material. This may be due to the factory installation process.
Associated Products (3)Associated Documents - March 14, 2024•Document ID: 10252628Service Bulletin/Repair InstructionsSTRUCTURE:BODY:DOOR; ELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- SSM 52364
- Date Added:
- April 4, 2024
- Manufacturer:
- FORD
Summary2021-2023 Bronco vehicles built on or before 9-Jul-2023 may have new version software in their driver door module (DDM) and passenger door module (PDM) that contains noticeable enhancements to the window short drop operation. This software level can be identified in the DDM and PDM as Software Part Number MU5T-14C064-CR or later. This software was released via a software update delivered over-the-air (OTA) starting in September 2023 if the vehicle's connectivity was enabled in the vehicle settings. Vehicles with this new software will exhibit a short drop event to all door windows anytime the vehicle is unlocked using the remote keyless entry (RKE), accessory keyless entry keypad, or the interior door unlock switch. The short drop function will return to the UP position when a lock input is received from these same inputs. For vehicles equipped with passive entry, a short drop event will not activate when a door is unlocked by placing a hand on an exterior door handle. 2023-2024 Bronco vehicles built on and after 10-Jul-2023 received this software from the factory.
Associated Products (4)Associated Documents - March 13, 2024•Document ID: 10252624Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- SSM 52354
- Date Added:
- April 4, 2024
- Manufacturer:
- FORD
SummarySome 2023 Bronco vehicles may exhibit diagnostic trouble code (DTC) U2101 stored in accessory protocol interface module (APIM) and/or telematics control unit (TCU) after TCU module programming with no additional symptoms present. This may be due to the TCU configuration. To correct the concern, download and run the TCU-Telematics Control Unit (TCU) Module Configuration application using Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 14F546 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Associated Products (1)Associated Documents - March 8, 2024•Document ID: 10251956Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- SSM 52345
- Date Added:
- March 20, 2024
- Manufacturer:
- FORD
SummarySome 2022-2024 various Ford/Lincoln vehicles equipped with SYNC 4 may experience concern where customers are receiving an error message when trying to enroll in connected services. This may be due to the gateway module (GWM) software. To correct the concern, download and run the Transport and Factory Mode Deactivation app: under HS1 modules select BCM > Transport and Factory Mode > Download > Run. When the pop-up message appears for Change Vehicle Mode - Transport/Factory/Normal Mode, press OK. This will proceed to the Transport and Factory Mode Deactivation screen, select Unlock Vehicle Connectivity Settings (21 MY + Vehicles). A pop-up message appears noting Vehicle Is Now In Normal Mode, select OK. This will return to the Transport and Factory Mode Deactivation screen, select Exit. A final pop-up notification stating that the application is finished, select OK. For claiming, use causal part 14G490 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Associated Products (19)2024 Ford Bronco2024 Ford Edge2024 Ford Escape2024 Ford Expedition2024 Ford F-1502024 Ford Mustang2024 Ford Ranger2024 Ford Transit2024 Lincoln Corsair2024 Lincoln Navigator2023 Ford Bronco2023 Ford Edge2023 Ford Escape2023 Ford Expedition2023 Ford F-1502023 Ford Transit2023 Lincoln Corsair2023 Lincoln Nautilus2023 Lincoln NavigatorAssociated Documents - March 7, 2024•Document ID: 10251954Service Bulletin/Repair InstructionsPOWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
- Mfr Comm. #:
- SSM 52342
- Date Added:
- March 20, 2024
- Manufacturer:
- FORD
SummarySome 2022-2024 Broncos Raptors built on and before 13-Feb-2024 and 2021-2024 Broncos equipped with a 2.3L EcoBoost engine may exhibit an illuminated MIL with ignition system DTC(s) P0352, P0353, P0354, P0355, P0357, P2303, P2306, P2309, P2312, P2318, P2304, P2307, P2310, P2313, P2319, and/or P2322 set in the powertrain control module (PCM). This may be due to incorrect cylinder to DTC mapping within the PCM. This means the DTCs listed may set against the incorrect cylinder. Even though the cylinder to DTC mapping is incorrect in the PCM, the presence of these DTCs means that a real ignition system concern is present that requires diagnosis and repair. Prior to performing a pinpoint test for one of the listed DTCs, it will be necessary to identify the correct cylinder that has the issue. Do this by using the Ford diagnosis and repair system (FDRS) to perform a cylinder power balance test. If the results show two cylinders dropping out, begin diagnosing the ignition system components for the cylinder that is dropping out and not setting an ignition related DTC. Due to the incorrect cylinder to DTC mapping
Associated Products (4)Associated Documents - March 6, 2024•Document ID: 10251952Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- SSM 52335
- Date Added:
- March 20, 2024
- Manufacturer:
- FORD
SummaryFor 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
Associated Products (60)2024 Ford Bronco2024 Ford Bronco Sport2024 Ford Edge2024 Ford Escape2024 Ford Expedition2024 Ford Explorer2024 Ford F-1502024 Ford Maverick2024 Ford Mustang2024 Ford Ranger2024 Ford Transit2024 Lincoln Aviator2024 Lincoln Corsair2024 Lincoln Nautilus2023 Ford Bronco2023 Ford Bronco Sport2023 Ford Edge2023 Ford Escape2023 Ford Expedition2023 Ford Explorer+ 40 moreAssociated Documents - March 6, 2024•Document ID: 10251950Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM
- Mfr Comm. #:
- SSM 52333
- Date Added:
- March 20, 2024
- Manufacturer:
- LINCOLN
SummaryMany body control module C (BCMC) warranty return parts are coming back with no trouble found. To verify that the BCMC is at fault prior to replacing, perform the following. First, disconnect the battery then check all BCMC connectors for terminal pushout, pin damage, spread terminals, and corrosion. Refer to Workshop Manual Section 100-00 Wire Terminal Inspection and Replacement. If none found, reconnect the BCMC and battery terminals then recheck functionality. If concern still exists, proceed with BCMC replacement.
Associated Products (8)Associated Documents - March 4, 2024•Document ID: 10251947Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE; EQUIPMENT:ELECTRICAL:INFOTAINMENT
- Mfr Comm. #:
- SSM 52328
- Date Added:
- March 20, 2024
- Manufacturer:
- FORD
SummarySome 2021-2024 Bronco/F-150, 2023-2024 Escape/F-Super Duty vehicles equipped with SYNC 4 may experience a concern during accessory protocol interface module (APIM) programming where the vehicle's center display screen indicates USB Error. This may be due to a lack of memory space available to perform the APIM software update. If it is a memory concern, the Ford Diagnosis and Repair System (FDRS) will provide an option to delete the voice application. Re-enter the module programming and when prompted, do not select first option - SYNC Module (APIM) Software Update, select the second option - Delete Voice Application(s) From Module. Once deleted, run the SYNC Module (APIM) Software Update as directed, this will update the software and automatically reload the voice app. If the voice delete option is not available, continue with normal diagnostics in the Workshop Manual, Section 418.
Associated Products (10)Associated Documents - March 1, 2024•Document ID: 10251934Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- SSM 52314
- Date Added:
- March 20, 2024
- Manufacturer:
- FORD
SummaryDuring service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
Associated Products (67)2024 Ford Bronco2024 Ford Bronco Sport2024 Ford E-3502024 Ford E-4502024 Ford Edge2024 Ford Escape2024 Ford Expedition2024 Ford Explorer2024 Ford F-1502024 Ford Maverick2024 Ford Mustang2024 Ford Transit2024 Lincoln Aviator2024 Lincoln Corsair2024 Lincoln Nautilus2024 Lincoln Navigator2023 Ford Bronco2023 Ford Bronco Sport2023 Ford E-3502023 Ford E-450+ 47 moreAssociated Documents - February 22, 2024•Document ID: 10251466Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- TSB 24-2042
- Date Added:
- March 7, 2024
- Manufacturer:
- FORD
SummaryThis article supersedes TSB 23-2019 to update the model years affected, add an additional labor operation, and correct the part number called out in the Service Procedure. Some 2021-2024 Bronco vehicles equipped with a MT88 manual transmission may experience a rotational scraping noise while the transmission is in neutral, 1st or 2nd gear with the clutch pedal released and may be more noticeable in ambient temps below 10ðC (50ðF) and after a cold soak. This noise may diminish as the transmission warms up. This may be due to the 5th and 6th gear synchronizer rings.
Associated Products (4)Associated Documents - February 21, 2024•Document ID: 10250832Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- SSM 52278
- Date Added:
- March 5, 2024
- Manufacturer:
- FORD
SummarySome 2021-2023 Bronco (non-Raptor) vehicles built on or before 09-Jul-2023 may exhibit a fluid leak from the front drive axle pinion seal. This may be due to operating the vehicle under high load. If leaking, replace the pinion seal following Workshop Manual (WSM) section 205-03A > Removal and Installation > Drive Pinion Flange and Seal. To prevent subsequent seal leaks, the front differential fluid must also be replaced using the revised specification Motorcraftî SAE 75W-85 Premium Synthetic Hypoid Gear Lubricant, part number XY-75W85-QL. Refer to WSM section 205-03A > General Procedures > Differential Draining and Filling. For claiming use causal part number 3254 with applicable labor operations in Section 3 of the Service Labor Time Standards (SLTS) Manual and M-Time. Reference this SSM article number in the warranty claim.
Associated Products (3)Associated Documents - February 19, 2024•Document ID: 10251486Service Bulletin/Repair InstructionsBACK OVER PREVENTION:SOFTWARE; ELECTRICAL SYSTEM
- Mfr Comm. #:
- OTAPU0102SVDFXBr
- Date Added:
- March 7, 2024
- Manufacturer:
- FORD
SummarySoftware Update 24-PU0102-SVD-FX for 2023 MY BRONCO vehicles is now available. Quality improvements include: - Improved OTA deployment
Associated Products (1)Associated Documents - February 19, 2024•Document ID: 10251232Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- 23B21 S1
- Date Added:
- March 5, 2024
- Manufacturer:
- FORD
SummaryCertain 2023 Model Year F-150 and Bronco Vehicles - Gateway Module Programing
Associated Products (2)Associated Documents - February 16, 2024•Document ID: 10251465Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- TSB 24-2040
- Date Added:
- March 7, 2024
- Manufacturer:
- FORD
SummarySome 2021-2024 Bronco vehicles may exhibit paint damage on the rear quarter panel due to contact with the soft top rear window. This may be due to a contact condition that can occur during extreme off-road driving between the soft top rear window and the rear quarter panel. To correct the condition, follow the Service Procedure to modify the rear window.
Associated Products (4)Associated Documents - February 13, 2024•Document ID: 10250522Service Bulletin/Repair InstructionsLATCHES/LOCKS/LINKAGES:DOORS:LOCK; ELECTRICAL SYSTEM
- Mfr Comm. #:
- SSM 52258
- Date Added:
- February 23, 2024
- Manufacturer:
- FORD
SummarySome 2021-2024 Bronco vehicles may exhibit a parasitic battery draw. This may be due to an interior door lock switch on the driver's and passenger's interior door panels. Prior to normal Workshop Manual (WSM) diagnostics, check both front door lock control switches for damage and/or proper operation. If a front door lock control switch does not operate as designed, repair as necessary. If no problems are found, continue with normal WSM diagnostics. For claiming, use causal part 14028 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. If the draw is still present, refer to WSM Section 414-00 for normal diagnostics.
Associated Products (4)Associated Documents - February 5, 2024•Document ID: 10251460Service Bulletin/Repair InstructionsEQUIPMENT; STRUCTURE:BODY:TRUNK LID
- Mfr Comm. #:
- TSB 24-2032
- Date Added:
- March 7, 2024
- Manufacturer:
- FORD
SummarySome 2021-2023 Bronco vehicles built on or before 28-Feb-2023 may exhibit water entry into the rear trunk. This may be due to a lack of body seam sealer at the floor panel to trunk sheet metal joint. This repair procedure addresses water entry from underneath of the vehicle into the rear trunk area (jack storage compartment). This article does not apply if water is entering the vehicle from above the rear trunk area (such as from the roof, rear window etc.). To correct the condition, follow the Service Procedure to apply seam sealer to the forward trunk to floor panel sheet metal joint.
Associated Products (3)Associated Documents - January 31, 2024•Document ID: 10249780Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:TV/RADIO/SPEAKERS
- Mfr Comm. #:
- SSM 52225
- Date Added:
- February 6, 2024
- Manufacturer:
- FORD
SummarySome 2023 Bronco vehicles equipped with a B&O sound system and built on 28-Jul-2023 and through 29-Aug-2023 may experience an intermittent loss of audio from certain speakers. Function should return with a key cycle and the symptom may return within every 1-20 additional key cycles. This may be due to the software within the audio digital signal processing module (DSP). To correct the condition, reprogram the DSP module to the latest software level using the Ford Diagnosis and Repair System (FDRS) diagnostic scan tool. For claiming, use causal part 18B849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Associated Products (1)Associated Documents - January 24, 2024•Document ID: 10249787Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- TSB 24-2021
- Date Added:
- February 6, 2024
- Manufacturer:
- FORD
SummaryThis article supersedes TSB 23-2213 to revise Figure 1, add 2024 vehicles and the part list. Some 2021-2024 Bronco vehicles may exhibit a whistle noise below the lower left windshield area at the bottom of the A-pillar. This may be due to a missed body sealer application at the factory.
Associated Products (4)Associated Documents