Jeep Wrangler Complaints

18,838 consumer complaints on file.

#11746787June 26, 2026
SERVICE BRAKES, HYDRAULIC
The contact owns a 2014 Jeep Wrangler. The contact stated that while starting the vehicle, several unknown warning lights were illuminated. The traction control, cruise control, and ABS features were inoperable. The vehicle was taken to an independent mechanic, and DTC: C2200 was retrieved. It was determined that the ABS module needed to be replaced; however, the part was on backorder. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 93,000.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11746761June 26, 2026
VEHICLE SPEED CONTROL, ENGINE, ELECTRICAL SYSTEM
When I am driving I will lose power and not be able to drive while I am in the middle of a road driving. And I have to turn my car completely off to let it start back up. The dealership doesn’t not seem to have any more suggestions or recommendations. I feel unsafe driving this vehicle. This keeps happening
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11746682June 26, 2026
ELECTRICAL SYSTEM, ENGINE, FUEL/PROPULSION SYSTEM
I took my car to the dealership to complete the 04b recall. When I got my car back from this recall: 1. The car says driving in electric mode but it uses gas. 2. The car while driving on the highway will hesitate for a split second.. very dangerous. 3. When going on a small hill(example: bridge on turnpike over griffon road) will all of a sudden hesitates and will not get any more power. 4. Multiple times when getting off the turnpike the car slowed to 20mph and would not go any faster for about 15 seconds.. all this while in electric mode.. even more dangerous... I took the jeep back to the dealership, they have had the car for 6 weeks and acknowledge the problems..but Stellantis keeps saying this is normal.. not normal, did not happen before the recall.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11746651June 26, 2026
ENGINE, ELECTRICAL SYSTEM
Recurring incident after completion of Jeep recall software update 68C intended to address fire hazard associated with the vehicle's hybrid battery. Since that update, when driving in standard Electric mode, the vehicle experiences a sudden loss of power, hesitation, and a physical 'bogging down'. Following this, the vehicle abruptly surges into combustion engine mode, causing a sudden and unpredictable acceleration lurch just after the vehicle has hesitated to accelerate. It poses a hazard for rear-end collision, attempting to pick up speed (e.g., to pass or move from a vulnerable position) and overall maneuvering and operation of the vehicle.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11746627June 26, 2026
FUEL/PROPULSION SYSTEM, ENGINE
2023 JEEP Wrangler Sahara 4xe has been recalled several times for battery potential fire risk issues due to faulty hi voltage battery design. Each time, a software patch was applied to provide a 'fix'. With my engineering background, I am very sensitive to machinery and its behavior. I have noticed with each successive update, the power output of the traction battery has been capped or limited to restrict maximum current draw from the battery to prevent over heating. With the latest 68C recall, there is now a clear safety issue. Power is restricted so much, pulling on a highway is dangerous. As I accelerate, battery output climbs to 50%, the engine comes on and there is a significant pause before acceleration can resume safely. Under battery only acceleration, the car bogs down with loss of power. The 4xe no longer resembles the vehicle I purchased. Jeep needs to do a physical remedy to restore original specs or buy back the car, 100% of purchase price. This is a clear safety issue. While Jeep has tried to fix the fire risk, they have created a new safety hazard.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11746609June 26, 2026
ENGINE, FUEL/PROPULSION SYSTEM, ELECTRICAL SYSTEM
Since the 68C recall from Jeep, my vehicle has not been functioning properly. The 68C recall was issued because the high-voltage battery cells have a defect that causes them to short-circuit and catch fire. To avoid replacing hundreds of thousands of expensive batteries all at once, Jeep implemented a "fix" via a software flash. The new software "fix" heavily restricts how much power can be drawn from the high-voltage battery to keep it from getting warm. If you push the pedal enough to draw more than roughly 40–50% power—or if the battery temperature hits a strictly lowered threshold—the software abruptly chokes the electric motor and fires up the ICE engine to compensate. Because the electric motor just lost its punch, the computer frantically fires up the gasoline engine to make up the difference. Because there is an inherent delay while the gas engine starts up and matches the transmission speed, it engages with a sudden, frustrating lurch or surge. This is just one of the many problems i have found since jeeps "fix" has been implemented. Basically Jeep elected to reduce the capacity of the battery to avoid costly replacement of the real issue with the battery. This has resulted in a driving safety concern with the surging and hesitation. Also now I can no longer drive exclusively in the electric mode; electric mode is basically non-existent.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11746607June 26, 2026
ENGINE, ELECTRICAL SYSTEM
I have a 2024 Jeep Wrangler 4xe plug in hybrid. When I first got the vehicle I could drive in the electric mode without kicking over to the gasoline mode. The manufacturer issued a recall for the battery due to fire danger. I had an update 68c performed by the dealer to address the recall issue. Upon getting my Jeep back I can no longer drive in the electric mode without the Jeep surging into and out of the gas mode. This happens at different times, slow speeds or fast speeds. The jeep does hesitate or bogs down prior to engaging the gas mode. After takinThe 68C recall was issued because the high-voltage battery cells have a defect (separator damage) that causes them to short-circuit and catch fire. To avoid replacing hundreds of thousands of expensive batteries all at once, Stellantis implemented a "fix" via a software flash. Here is exactly what that software is doing to your driving experience: Aggressive Battery Throttling: The new software heavily restricts how much power can be drawn from the high-voltage battery to keep it from getting warm. If you push the pedal enough to draw more than roughly 40–50% power—or if the battery temperature hits a strictly lowered threshold—the software abruptly chokes the electric motor. The "Bogging" Sensation: When the software chokes the battery, the vehicle experiences a sudden drop in power. This is the hesitation or "bogging down" you feel. The Violent Engine Surge: Because the electric motor just lost its punch, the computer frantically fires up the gasoline engine to make up the difference. Because there is an inherent delay while the gas engine starts up and matches the transmission speed, it engages with a sudden, frustrating lurch or surge. Because this clunky, unrefined behavior was intentionally coded into the 68C update by corporate engineers to limit fire risks, your local dealer's computer diagnostics read "No Errors Found" and "Operating as Designed."
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11746391June 25, 2026
ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL, STEERING
The contact owns a 2019 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, the vehicle stalled. The contact pulled over and waited for several minutes before restarting the vehicle. The vehicle was taken to the dealer, who replaced the wiring harness, but the failure persisted with the speedometer and fuel gauge fluctuating and the instrument panel icons flashing. Additionally, the vehicle was jerking and experienced a loss of power steering assist while driving. The vehicle was jumpstarted. The vehicle was taken back to the dealer; however, the vehicle was not yet diagnosed or repaired. The contact related the failure to NHTSA Campaign Number: 24V652000 (Electrical System); however, the VIN was not included in the recall. The manufacturer was not made aware of the failure. The failure mileage was approximately 82,000.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11746517June 25, 2026
ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
The contact owns a 2020 Jeep Wrangler. The contact stated that while attempting to start the vehicle, the instrument cluster went blank. The vehicle was taken to the dealer where it was diagnosed with instrument cluster failure. The contact was informed that the instrument cluster needed to be replaced. In addition, the contact was advised that the repair was required prior to the vehicle being released back to the contact. The vehicle was repaired. The contact referenced an unknown recall; however, the VIN was not associated with a recall related to the failure. The manufacturer was made aware of the failure but provided no assistance. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was approximately 69,003.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11746578June 25, 2026
FUEL/PROPULSION SYSTEM
My jeep wrangler is currently having a very strong of fuel and when the ac is on the smell is very strong inside the cabin i came across a article stating that alot of 2020 jeep wrangler with 2.0L motors were recalled because of the same issue but my car was not recalled and im having the same issue of why the recall was done. What can i do is there anything you can help me with??
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11746245June 24, 2026
STEERING
Death Wobble. Going over 70 or under 30. Violently shakes the steering wheel and causes driver to lose control. More than once have I gone off the roadway.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11746276June 24, 2026
ELECTRICAL SYSTEM, POWER TRAIN, FUEL/PROPULSION SYSTEM
RE: SAFETY COMPLAINT FOLLOWING RECALL 68C (NHTSA Recall Number 24V-111 / Mopar 68C) I am the owner of a 2022 Jeep Wrangler Rubicon 4xe. Prior to having safety recall 68C performed, the hybrid system functioned flawlessly. Immediately upon receiving the vehicle back from the dealership after the 68C software flash, a severe drivability and safety hazard emerged. When driving in standard Hybrid/Electric mode, the vehicle experiences a sudden loss of power, hesitation, and a physical 'bogging down' sensation. Following this lag, the vehicle violently surges into gasoline mode, causing a sudden and unpredictable acceleration lurch after the vehicle hesitates to accelerate. This behavior occurs randomly at both low neighborhood speeds and highway speeds, making it impossible to smoothly modulate throttle input. This creates an immediate safety hazard when attempting to pull out into cross-traffic, merge onto highways, or maintain a safe, predictable following distance. The vehicle hesitates when throttle is demanded, creating a risk of being rear-ended, followed by an uncommanded surge. The dealership states the vehicle is 'operating as designed' according to a regional Jeep field engineer, implying this dangerous lag-and-surge behavior was intentionally introduced into the vehicle's management software by the manufacturer to mitigate, the recall notice noted above, battery thermal risks at the expense of occupant driving safety. The manufacturer’s recall remedy has traded a fire risk for an active moving traffic hazard." Several forums and AI searches show this is a common problem the manufacturer has created to avoid a costly recall by addressing the real issue with the battery’s fire risk. Instead they have intentionally reduce the battery’s performance causing a safety issue with the vehicle’s acceleration and operation.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11746270June 24, 2026
ELECTRICAL SYSTEM, STEERING, SUSPENSION
I am reporting a safety concern involving my vehicle’s steering system, front-end condition, and a recall I was not informed about. I brought the vehicle in for a routine tire rotation, at which time I was informed that the front camber was out of specification and that there was uneven wear on the front tires. An alignment was recommended. In addition, the vehicle is experiencing abnormal steering behavior. The steering wheel has a noticeable shake and does not feel normal during operation. This suggests a possible issue with the power steering system or related suspension components. The combination of uneven tire wear, improper camber, and a shaking steering system presents a significant safety risk. These issues may affect vehicle stability, steering control, and tire integrity, increasing the risk of loss of control while driving. I have also recently learned that there is an active recall affecting this vehicle, of which I was not previously notified. The fact that this recall was not communicated raises additional safety concerns, especially given the steering-related symptoms currently present. These conditions were identified during a recent service visit, and the underlying cause has not yet been resolved. I am concerned that this may represent a broader defect involving the steering or suspension system that could impact vehicle safety and that proper recall notification procedures may not have been followed.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11746110June 24, 2026
ELECTRICAL SYSTEM, POWER TRAIN, ENGINE
1. The vehicle caught fire during normal operation. It is a 2021 Jeep Wrangler (VIN [XXX]) subject to FCA US Recall 21D / NHTSA Campaign 26V363000, which identifies the electric hydraulic power steering (EHPS) pump and its wiring as a fire source that can overheat and ignite. The exact failed component has not yet been confirmed by diagnostic, but the fire is consistent with the defect described in that recall. The vehicle is intact and available for inspection — it was towed to Waxahatchie Jeep, an authorized Stellantis dealer in Waxahachie, TX, on June 19, 2026 and remains in their custody under repair order [XXX]. 2. The vehicle caught fire while being driven on the highway between Waxahachie and Ennis, Texas, with two occupants returning from a Boy Scout trip, my husband, the driver, and our [XXX] son. The driver was forced to take evasive action, steering off the roadway into a service station to get the occupants clear and stop the fire from spreading further. This created a serious risk of burns, of a collision during the evasive maneuver, and of harm to the occupants and other motorists. 3. Has the problem been reproduced…? No. No diagnostic has been performed. The vehicle has been in the authorized dealer’s custody since June 19, 2026 ([XXX]), but the manufacturer has not completed an inspection or diagnostic. The underlying defect is the subject of an active recall (21D / 26V363000) affecting more than one million 2021–2025 Jeep Wrangler and Gladiator vehicles, for which the manufacturer has stated no remedy is yet available. 4. The vehicle was towed by AAA to Waxahatchie Jeep on June 19, 2026 and has remained there since. It has not yet been formally inspected or diagnosed by the manufacturer. 5. There were no warning lamps or messages prior to the fire. The first indication of a problem was smoke from the engine area at which point the driver immediately pulled off the road and saw a plume of smoke coming from the exhaust. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11745854June 23, 2026
POWER TRAIN, STEERING, SERVICE BRAKES, HYDRAULIC
The contact owns a 2018 Jeep Wrangler. The contact stated that while driving 20 miles away after an hour, the vehicle lost power steering and power braking functionality, and the transmission unexpectedly downshifted to a lower gear. The vehicle was turned off. The check engine warning light was illuminated. The vehicle was towed to the residence. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 91,300.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11746023June 23, 2026
FUEL/PROPULSION SYSTEM
Jeep purchased new on 28 January 2026. Fuel gauge only goes to 7/8 full after tank is full. Took it to dealer, they replaced gas tank, then 2 weeks later fuel pump twice, and fuel sensor unit. This solved the problem for 32 days now it’s doing the same thing. Took it back to dealership, they stated there was nothing they could do and engineering is aware and working on a fix. Called another Jeep service they said they weren’t aware of any updates or recalls.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11745937June 23, 2026
STEERING, SUSPENSION
Violent front-end oscillation at 65 mph after hitting a bump, resulting in temporary loss of vehicle control. Happened y times. All at legal highway speeds. I had to bring the shuddering vehicle across multiple lanes of traffic to pull over and stop the vehicle to stop the violent shuddering. Vehicle is stock.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11745923June 23, 2026
ELECTRICAL SYSTEM
The 3.5-inch instrument panel cluster (IPC) in my Jeep has completely failed and gone blank. This is the exact safety defect described in NHTSA Campaign Number 24V652 (FCA Recall 30B). Because the screen is completely blank, I am entirely unable to see critical safety information while driving, including my speedometer, fuel gauge, and warning lights, which significantly increases the risk of a crash. Despite my vehicle experiencing the exact internal short circuit defect outlined in the official recall report, my vehicle is being excluded from free repairs because the manufacturer narrowed the scope based on the vehicle's "time in service." A local Jeep dealership has diagnosed the vehicle and confirmed the cluster needs to be replaced, but quoted me out-of-pocket costs to fix it. I believe the parameters for Recall 24V652 are dangerously narrow and need to be expanded to include my vehicle, as the defective component is actively failing and posing a hazard on the road.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11745918June 23, 2026
STEERING, ELECTRICAL SYSTEM, UNKNOWN OR OTHER
My 2022 Jeep Wrangler is subject to NHTSA Recall 26V363000 involving power steering wiring that may overheat and cause a vehicle fire. I was advised of the safety risk and informed that repair parts are not expected to be available until approximately August 2026. Due to the risk of fire, I do not feel safe keeping this vehicle at my home or parked near my residence until the recall repair is completed. The dealership has advised that no repair is currently available. I am requesting assistance from the manufacturer, including alternate transportation, a loaner vehicle, or other accommodations, until the safety defect can be repaired. I believe it is unreasonable to require owners to continue possessing a vehicle with a known fire risk while the recall remedy is unavailable for an extended period.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11745849June 23, 2026
SUSPENSION
Summary of Issue: The vehicle exhibited a repeatable dangerous steering oscillation after encountering road irregularities at speed. This occurred multiple times and is consistent with the known Wrangler “death wobble” condition for which a class action settlement exists on prior MY vehicles. Context: The wobble occurred several times during 2025, always on the highway. The violent oscillation (which seemed harmonic in nature) occurred when driving 65-70mph after running on a bumpy stretch of road (which basically describes most of Michigan right now). The only remedy was for the driver to immediately hit the warning lights, brake and slow down to around 20-25mph to reduce the oscillation, thereby regaining control. The Jeep service shop replaced all four shocks and the steering stabilizer, in addition to checking wheel alignment/balance etc. Additional Technical Context: I believe the Wrangler 4xe’s unique mass distribution may be contributing to the oscillation behavior, likely resulting in it acting differently to gas-powered Wranglers, The 4xe uses the same solid axle front suspension architecture as the gas powered Wrangler, but the hybrid model carries approximately 500–800 lbs of additional mass, much of it located low in the chassis and near the axle line. This added mass increases the effective unsprung and “near unsprung” inertia the suspension must control when the axle encounters a road disturbance. This higher inertia increases the energy transmitted into the track bar, tie rod ends, ball joints, and steering damper, reducing the system’s tolerance for even minor compliance, wear, or alignment deviation. It is my belief that the 4xe’s additional mass can amplify oscillation behavior after a bump, making the vehicle more susceptible to steering shimmy or ‘death wobble’ if any component is marginal.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0

← Back to Jeep Wrangler