Ford F-150 Complaints
39,812 consumer complaints on file.
- #11754376August 3, 2026POWER TRAIN
The vehicle experienced an uncommanded, severe downshift from 5th gear directly into 1st gear while traveling at approximately 45 mph on a public road. This caused sudden, violent engine braking and an immediate drop in speed, creating an extreme rear-end collision hazard and potential loss of vehicle control. This vehicle previously received the PCM software update under Ford Safety Recall 24S37 (NHTSA Campaign 24V444). The software update failed to prevent the sudden downshift event caused by the failing Output Shaft Speed (OSS) sensor on the transmission molded lead frame. When contacting Ford Corporate Customer Service and local dealerships, Ford refused to cover diagnostic scanning or hardware replacement, claiming the recall is marked "completed" in their database because the software patch was installed more than 12 months ago. A software update that fails to prevent a 5th-to-1st downshift leaves a defective physical sensor on the road. Ford is refusing to evaluate or remedy a persistent, life-threatening recall failure on a 6R80 transmission.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11754442August 3, 2026SERVICE BRAKES
While driving, brakes pushed to floor, and vehicle alarm beeped showing Low brake fluid sensor had tripped. Brakes not working properly, pedal goes to floor, brake fluid added to refill and fluid emptied out of master cylinder reservior two more times, vehicle inoperable to drive with no brake pressure. Open safety recalls for Ford F150 models 2013-2014 #16S24, and for F150 Models 2014-2017 #20S31, both specifically for the 3.5LV6 Ecoboost engine, which I have, but Ford is saying that mine is not covered for the same brake master cylinder / brake booster issue.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11754496August 3, 2026ENGINE
The contact owns a 2015 Ford F-150. The contact was notified that the VIN was included in an unknown recall, and the vehicle was repaired under the recall; however, while stopped at a red light, the vehicle stalled. The check engine warning light was illuminated. The vehicle was taken to a dealer where it was diagnosed and determined that the valve body and several other unknown components needed to be replaced. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 120,000.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11754497August 3, 2026POWER TRAIN, SERVICE BRAKES, VEHICLE SPEED CONTROL
I am reporting a safety-related transmission problem I experienced with my 2023 Ford F-150 equipped with the 10R80 automatic transmission. While driving normally, the transmission suddenly does not accelerate for up to 3 seconds while pressing the gas pedal, brakes either harshly or too soft at varying times, and very irregularly. This occurred while accelerating onto the highway, and almost every time I am braking at a stop sign or light, creating a potentially dangerous situation because the truck did not respond as expected when I needed predictable acceleration, propulsion, or deceleration. I believe this incident may be related to the known 10R80 CDF clutch-cylinder/sleeve problem. Ford technical information identifies axial movement of the CDF sleeve that can cause hydraulic-circuit leaks and harsh or delayed engagement and shifting. This condition can result in slipping, RPM flares, delayed engagement, unexpected gear changes, harsh downshifts, lurching, or loss of propulsion. This is a safety concern, not merely a transmission quality or reliability issue. Unexpected loss of propulsion or unpredictable shifting while merging, accelerating into traffic, crossing an intersection, turning, traveling at highway speeds, slowing down, and stopping, can create a collision hazard. Because I personally experienced this unexpected transmission event, I request that NHTSA investigate the 10R80 CDF clutch-cylinder/sleeve condition in Ford F-150s. Please review Ford warranty claims, dealer repair records, transmission replacements, consumer complaints, and field-failure data to determine whether this is a safety defect requiring a recall. I believe owners should not have to wait for a potentially dangerous transmission failure before this known condition is addressed.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11754506August 3, 2026POWER TRAIN, UNKNOWN OR OTHER
Vehicle Information: Year: 2014 Make: Ford Model: F-150 Component: Power Train (Transmission / Powertrain Control Module) Dealership Involved:Midway Motors Ford, 2075 E Kansas Ave, McPherson, KS 67460 Complaint Description:I am filing a formal safety complaint against Ford Motor Company and Midway Motors Ford in McPherson, KS, for failing to provide a free remedy under active federal safety recall 24S37 (NHTSA Campaign 24V444).My 2014 Ford F-150 was brought to the dealership to complete safety recall 24S37, which addresses severe, sudden transmission downshifts. The dealership performed a software update to the Powertrain Control Module (PCM). Immediately following this update, the truck's drivability severely deteriorated, and the transmission began violently slamming into 3rd gear, locking itself into a dangerous transmission fault "limp mode." The diagnostic scans post-update indicate a failure of the molded lead frame/speed sensor. According to Ford's official technical service bulletin for recall 24S37, physical replacement of the molded lead frame is an explicitly authorized remedy when diagnostic codes appear following the software flash. However, both the local servicing dealership (Midway Motors Ford) and Ford Corporate Customer Service are actively refusing to perform this physical safety repair free of charge. They are wrongfully claiming that because my vehicle has over 200,000 miles, it is disqualified from financial assistance. They are confusing a federal, non-expiring safety recall with an older, expired warranty extension program (19N01).By refusing to replace the defective lead frame that their own software update triggered into an active failure state, the manufacturer and dealer are leaving my vehicle in an unsafe, undrivable condition and violating federal recall mandates. I request that NHTSA intervene to compel Ford to complete the mandatory safety recall remedy at zero cost to me.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11754518August 3, 2026STRUCTURE:BODY
The dealership sold this vehicle to me with a rusted frame
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11754544August 3, 2026POWER TRAIN
The contact owns a 2015 Ford F-150. The contact stated that while driving at an undisclosed speed, the transmission unexpectedly downshifted. The transmission warning light was illuminated. The contact used a fluid cleaner, and the light turned off. The contact received notification of NHTSA Campaign Number: 26V237000 (Power Train). The contact called the local dealer, and it was confirmed that the part was on back order. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The approximate failure mileage was 153,000.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11754598August 3, 2026POWER TRAIN
I am filing a safety complaint regarding a recurring, hazardous transmission failure during highway and incline driving (specifically experienced on mountain highway passes in Arkansas). While driving at highway speeds on uphill inclines, the transmission severely hesitates and struggles to downshift under load. When it finally engages, it violently slams into gear. During these episodes, the truck experiences a sudden loss of motive power and acceleration lag, accompanied by an engine RPM flare of over 400+ RPM. And most recently, I have Live diagnostic data captured during operation revealed a downshift delay of over 3 seconds where the powertrain control module commanded 8th gear, but the transmission physically remained stuck in 10th gear due to severe internal hydraulic pressure loss. This defect presents a severe safety risk on high-speed roadways. Sudden, unexpected loss of power while climbing grades or merging into traffic creates an immediate risk of rear-end collisions from surrounding vehicles. This issue directly correlates with Ford Technical Service Bulletin TSB 26-2287, which identifies axial movement/slippage of the CDF clutch cylinder sleeve as the root cause of internal fluid leaks and gear failure. Because this internal hardware failure causes unpredictable power delivery and driveability loss at highway speeds, I request that the NHTSA investigate the 10R80/10R80-MHT transmission CDF drum sleeve defect as a critical safety hazard. Finally, Ford motor company, and most cases refuses to repair this known defect under warranty, many owners are experiencing this dealership pushback leaving them with a critical safety issue.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11754600August 3, 2026SERVICE BRAKES
Right front brake continuously freezes up making impossible to drive safely. ABS does not show any default or warnings. Truck shakes all over. Had rotors, calibers, and brake pads replied, but right side brake continues to freeze up. Brake lines checked and show no signs of collapse.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11754603August 3, 2026POWER TRAIN
Complete transmission failure at 76,000 miles.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11754607August 3, 2026SEAT BELTS
While removing child care seats from the back-right passenger seat, I noticed an unusually loud tingling sound from the lower anchor point of the seat belt. Upon inspecting it, I noticed that the bolt anchoring the bottom part of the seat belt was completely unscrewed and was only being held on by the tension of the seat belt. Once unbuckeled, the bottom anchor of the seat belt came out completely. There were no special circumstances to cause the seat belt bottom anchor to come unscrewed beyond normal use. Component is available for inspection upon request. The issue has not been brought to the attention of the dealer or manufacturer. The vehicle has not been inspected by anyone other than the owner. The unscrewing of a bolt that is critical to the proper function of a seat bealt through normal use and without any indicators or warnings creates serious unsafe conditions that could result in harm to oneself or others.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11754626August 3, 2026POWER TRAIN, VEHICLE SPEED CONTROL
My truck has shown wrench on dash multiple times, dropped gear several times suddenly. Less than 10 years old but over 150,000 miles so Ford has agreed to a fix under extended warranty program 26N04. Unfortunately they were allowed to add the phrase whichever comes first. This eliminates me from getting them to fix the cause which is the lead frame module. A PCM will not fix a bad part. This is a dangerous safety issue that should be fixed by Ford. Please save lives and get them to replace all lead frame modules if code finds it bad. It could affect anyone’s family member if an accident results.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11754597August 3, 2026POWER TRAIN
My vehicle is having bad shifting and jerking from 1st to 2nd. It has now gotten worse and does the jerking through all gears at 81,000 miles. A certified Ford dealer is doing a diagnosis on it. But Ford wont cover anything as the transmission it has is widely know issue. The CDF drum is only a bulletin no full recall. This issues occures while driving and will shoot up to gear 8 and try to shift its self to 1st gear at 5 miles per hour struggling.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11754535August 3, 2026TIRES:TREAD/BELT
275/50 R22 I was driving on a major interstate approximately 65 mph when a strong vibration was felt. As I started to move to the shoulder and slow down, the tread detached from the tire. The tire remained on the vehicle but the tread delaminated and was in the middle of the highway. This caused significant (>$11k) damages to the truck. I sent the tire to Continental and they declined taking liability for the tire failure. However, this happened to another owner a week or two after my issue and they had the same tire with only 30k miles. Additionally, there is already a recall on the same type of tire (different size) from last year due to tire delamination. This is a serious safety issue that could result in fatalities.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11754519August 3, 2026POWER TRAIN
The contact owns a 2021 Ford F-150. The contact stated that while driving at various speeds, there was an abnormal clicking sound coming from the vehicle. The local dealer was made aware of the issue and upon inspection of the rear passenger’s side wheel end hub bolt, the dealer discovered the bolt was fractured. The contact later received notification of NHTSA Campaign Number: 23V896000 (Power Train); however, the part to do the recall repair was not yet available. The contact was advised that the vehicle should not be driven until the vehicle was repaired under the recall. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue but confirmed that parts were not yet available. The contact was provided a case number. The failure mileage was approximately 52,000.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11754406August 3, 2026STEERING
The contact owns a 2021 Ford F-150. The contact stated that while parking the vehicle, the vehicle unexpectedly lost power steering functionality. The contact opened and closed the driver's side door to reset the vehicle, and the power steering function was restored; however, the failure recurred while driving. The vehicle was towed to an independent mechanic, where it was diagnosed with a PSCM internal failure and steering mechanism ball retainer failure. The mechanic determined that the failure was associated with NHTSA Campaign Number: 21V407000 (Steering) and referred the contact to the dealer for assistance. The vehicle was towed to the dealer, and the issue was confirmed after a diagnostic test, but the contact was informed that parts were not yet available. The vehicle was not repaired. The manufacturer was notified of the failure, and a case was filed. The failure mileage was approximately 79,000.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11754379August 3, 2026POWER TRAIN
I am reporting a safety-related transmission problem I experienced with my 2021 Ford F-150 equipped with the 10R80 automatic transmission. While driving normally, the transmission suddenly downshifted hard, with a jolt that shook the whole truck, then went into emergency limp mode, where I had to pull over to the shoulder, on Interstate 240 in heavy traffic. I was attempting to accelerate to merge into merging traffic. Because of this it created a dangerous situation because the truck did not respond as expected when I needed predictable acceleration or propulsion. Other times I have had hard shifting, but did not result going into limp mode. I believe this incident may be related to the known 10R80 CDF clutch-cylinder/sleeve problem. Ford technical information identifies axial movement of the CDF sleeve that can cause hydraulic-circuit leaks and harsh or delayed engagement and shifting. This condition can result in slipping, RPM flares, delayed engagement, unexpected gear changes, harsh downshifts, lurching, or loss of propulsion. This is a safety concern, not merely a transmission quality or reliability issue. Unexpected loss of propulsion or unpredictable shifting while merging, accelerating into traffic, crossing an intersection, turning, or traveling at highway speed can create a collision hazard. Because I personally experienced this unexpected transmission event, I request that NHTSA investigate the 10R80 CDF clutch-cylinder/sleeve condition in Ford F-150s. Please review Ford warranty claims, dealer repair records, transmission replacements, consumer complaints, and field-failure data to determine whether this is a safety defect requiring a recall. I believe owners should not have to wait for a potentially dangerous transmission failure before this known condition is addressed.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11754342August 3, 2026FUEL/PROPULSION SYSTEM, ENGINE
I purchased a 2022 Ford F150 in September 2024. I began to notice occasional sluggishness when accelerating as the weather warmed up around March 2025. I contacted my local Ford dealership sharing the issue. The service manager suggested I consistently use a high octane fuel, which I consistently do, explaining I may just have "bad gas". The problem continued primarily when I was in heavy traffic with high temperatures. The truck acted as if it had a clogged fuel injector, sluggishness from start, low idle reducing below 1,000 RPM. I contacted a privately owned mechanic shop advising of my idle issues. The mechanic stated he doesn't believe a fuel injector would clog at 50,000 miles. In June 2025 received notification of a recall for my vehicle which I confirmed by VIN. The recall (#25V455) summarized the vehicle could sustain a loss of fuel pressure and flow from the fuel tank due to fuel pump failure. The letter continued, I may experience poor engine performance, rough idle or reduction in power, the same issues I had been complaining about. I contacted the Ford dealership and they explained Ford had not determined how to remedy the problem. Fast forwarding to present, 3 August 2026, over a year since the recall letter and Ford has yet to remedy the problem. What's the hold up? Will Ford finally determine the remedy when my family is killed on the interstate because the vehicles fuel pump fails and it stalls? It appears to be apparent Ford does not want to take the financial hit of such a recall. This is unacceptable and needs to be looked into by the NTSB.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11754238August 2, 2026POWER TRAIN
I am reporting a safety-related transmission problem I experienced with my 2021 Ford F-150 equipped with the 10R80 automatic transmission. While driving normally, the transmission suddenly has lost propulsion and RPMs flare while driving steadily uphill. This occurred while merging onto a fast moving highway and while traveling at a steady speed going uphill, creating a potentially dangerous situation because the truck did not respond as expected when I needed predictable acceleration or propulsion. I believe this incident may be related to the known 10R80 CDF clutch-cylinder/sleeve problem. Ford technical information identifies axial movement of the CDF sleeve that can cause hydraulic-circuit leaks and harsh or delayed engagement and shifting. This condition can result in slipping, RPM flares, delayed engagement, unexpected gear changes, harsh downshifts, lurching, or loss of propulsion. This is a safety concern, not merely a transmission quality or reliability issue. Unexpected loss of propulsion or unpredictable shifting while merging, accelerating into traffic, crossing an intersection, turning, or traveling at highway speed can create a collision hazard. Because I personally experienced this unexpected transmission event, I request that NHTSA investigate the 10R80 CDF clutch-cylinder/sleeve condition in Ford F-150s. Please review Ford warranty claims, dealer repair records, transmission replacements, consumer complaints, and field-failure data to determine whether this is a safety defect requiring a recall. I believe owners should not have to wait for a potentially dangerous transmission failure before this known condition is addressed.
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0
- #11754246August 2, 2026POWER TRAIN, FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL
Ive noticed that the electric motor sometimes doesnt want to disengage quickly when I step on the brakes. In this incident I had to make a hard brake because someone pulled out in front of me. I had the cruise control on. When I slammed on the brakes the vehicle did not stop fast the vehicle felt as if it was still being pushed by something. Then a small jolt was felt and then the vehicle finally slowed. Had I been going faster or had the car that pulled been closer. This fault would have resulted in an incident
- Crash:
- No
- Fire:
- No
- Injuries:
- 0
- Deaths:
- 0