Mercedes-Benz G-Class Service Bulletins

325 manufacturer communications on file.

• December 11, 2025•Document ID: 11026611

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.65-P-080132

  Date Added:

  December 15, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

  Associated Products (116)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLS-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class+ 96 more
  Associated Documents

  • DownloadMC-11026611-0001.pdf↗
• December 3, 2025•Document ID: 11026127

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.85-P-080094

  Date Added:

  December 4, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Displayed Message: “Driver camera not functioning, see Operator’s Manual” Cause Interior temperature too high due to: • Summer heat • Direct sunlight • Lack of air conditioning or ventilation Camera enters self-protection mode to prevent overheating. Remedy Do NOT replace any parts. The driver camera (NTG7: MDC295; CIVIC.i2: CIVIC206) is operating as designed. Allow the interior to cool down. If the message remains after cooling: • Run XENTRY Diagnosis • Check latest software for Actuation of Driver Camera (A26/17) No TIPS case required.

  Associated Products (54)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class+ 34 more
  Associated Documents

  • DownloadMC-11026127-0001.pdf↗
• November 18, 2025•Document ID: 11025646

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI68.20-P-080012

  Date Added:

  November 19, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint USB port not functioning properly. Cause Most reported USB port issues are due to improper use or contamination. Note: Any repair costs must be discussed with the customer beforehand. Common external factors identified include: • Fluid intrusion • Broken bushings or physical damage See attachments. Remedy If a component needs replacement but shows no visible external damage, submit a detailed TIPS case only when technical support is required. Include details of all connected external devices (such as charging cables, USB drives, and hard drives). If diagnostic results directly indicate component replacement, a TIPS case is not necessary.

  Associated Products (45)

  2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLC-Class2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz S-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLC-Class+ 25 more
  Associated Documents

  • DownloadMC-11025646-0001.pdf↗
• November 10, 2025•Document ID: 11025471

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI27.35-P-079971

  Date Added:

  November 11, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Possible complaints about shift quality, issues with learning the park lock, and slipping/rinse entries in the EEPROM or Transmission Health system following the replacement of the below components: - The electrohydraulic control unit (EHS valve body) in transmission 725.0/725.1 - The repair kit for the control unit (VGS) in transmission 725.0 Cause Missing, incorrectly installed, or damaged guide tubes on the EHS valve body. Remedy Check for the correct installation of the guide tubes (refer to attachments under “Cause”), correct installation if necessary. Parts Catalog References: NAG3M 725.1 AND NAG3C 725.0 (AMG only): Part numbers 100, 120, 150, 160 NAG3C 725.0 (Non AMG): Part numbers 280, 290, 330, 340 NOTE: If any of these guide tubes are not installed and the vehicle is driven, it will create several rinse and slipping events in the EEPROM data. These values caused by incorrect installation need to be erased to prevent future misdiagnosis. Submit a TIPS case to the Powertrain inbox with the following to receive the necessary reset password: - Initial Quick Test w/ Freeze frame data - VGS Control Unit Log - IPR Result - Initial EEPROM data (before repairs) - Latest EEPROM data - Photo of oil level ultrasonic measurement next to XENTRY specifications Please provide detail regarding the reasoning for the initial replacement in your workshop findings and measures performed. (This topic was covered in the July 2022 and July 2024 Passenger Car Tech Topics)

  Associated Products (94)

  2026 Mercedes-Benz AMG GT2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class+ 74 more
  Associated Documents

  • DownloadMC-11025471-0001.pdf↗
• November 6, 2025•Document ID: 11025544

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI68.20-P-080012

  Date Added:

  November 14, 2025

  Manufacturer:

  MERCEDES BENZ

  Summary

  Complaint USB port not functioning properly. Cause Most reported USB port issues are due to improper use or contamination. Note: Any repair costs must be discussed with the customer beforehand. Common external factors identified include: • Fluid intrusion • Broken bushings or physical damage See attachments. Remedy If a component needs replacement without visible external damage, submit a detailed TIPS case. Include information on all connected external devices (e.g., charging cables, USB drives, hard drives).

  Associated Products (67)

  2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz S-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class+ 47 more
  Associated Documents

  • DownloadMC-11025544-0001.pdf↗
• November 3, 2025•Document ID: 11025100

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI27.10-P-075869

  Date Added:

  November 6, 2025

  Manufacturer:

  MERCEDES-MAYBACH

  Summary

  Complaint Only vehicles with a variable transfer case are affected. This can be identified through control unit N45 or N15/7 in the quick test. When accelerating with light load, vibrations or jolting sensation may come from the drivetrain. It may be mistaken for a harsh shift. Cause Modified oil quality of the transfer case over time Remedy 1. Check initial quick test for faults in the following control units. N45 or N15/7 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present: Process them as per the guided test in Xentry. If no faults are present: 2. Check the transmission oil level If the oil level is correct: 3. Unplug the connector for the transfer cases control unit and reassess the vehicle on a subsequent test drive If the complaint no longer occurs with the control unit disconnected: 4. Perform an oil change of the transfer case according to WIS specifications - Collect an oil sample of the original fluid 5. Complete all transfer case Tech-in processes located under VG Control Unit > Adaptations - Resetting the oil service data - Calibration of N15/7 5. Perform road test of vehicle to bring transmission to operating temperature ( >60C ) 6. Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right 7. Perform an extended 200mi road test to ensure the clutches are properly conditioned with the new oil. 8. Reassess the concern and release the vehicle if no longer present. If the concern continues to occur with the control unit disconnected or after the above steps have been performed, please submit a TIPS case to the Powertrain inbox with the following information: - Initial quick test with fault freeze frame data - Initial transmission EEPROM data - VGS and Transfer Case Control Unit Log (N45 or N15/7) - Photo of the original oil condition - What color was the fluid drained from the transfer case before the oil change? - Was an oil sample collected, and can you provide a photo of the original fluid? - What color and part number fluid was used during the oil change? - How far was the vehicle driven after?

  Associated Products (103)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz GLC-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class+ 83 more
  Associated Documents

  • DownloadMC-11025100-0001.pdf↗
• October 29, 2025•Document ID: 11024620

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.71-P-078112

  Date Added:

  October 29, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint The concern is characterized by BOTH of the following. 1. "Active Distance Assist currently unavailable" and "Active Brake Assist functions currently limited" are shown on the instrument cluster during startup or while driving AND 2. Stored DTC in quick test U0416FE - "Implausible data were received from control unit Traction system" in A108/1 (Distronic). Cause Missing wire between Drive Unit (N145) and Supercap (C8). Remedy Please reference the following attachments prior to starting work to familiarize and verify the locations of the components: • Drive Unit (N145) - See attachment "Location of Drive Unit in the vehicle". • Supercap (C8) - See attachment "Location of Supercap C8 in the vehicle". Professionally create a new connection by: • Using a red/white cable with cross-section 0.35 mm² and overall length of approximately 2m. • Connect Drive Unit (N145) plug A pin 18 to the 3-pin plug of the Supercap (C8) terminal 15 pin 2. Reference the new wire routing location as shown by the red line in "Picture 1 - Connection from Supercap to Drive Unit". • The new wire should be added to the existing wiring harness as shown by the red line "Picture 1 - Connection from Supercap to Drive Unit". • Z-Splice is the preferred method using A 000 982 91 10 for the Supercap (C8) connection. NOTE: All WIS instructions must be followed for wiring modifications. Damage code: 0 - 51422 - ** - 7 (for ** please state the following: "missing connection ex factory"). If the vehicle has had the modification completed and returns with an exact matching "complaint", please open a TIPS case.

  Associated Products (9)

  2023 Mercedes-Benz G-Class2022 Mercedes-Benz G-Class2018 Mercedes-Benz G-Class2017 Mercedes-Benz G-Class2016 Mercedes-Benz G-Class2015 Mercedes-Benz G-Class2014 Mercedes-Benz G-Class2004 Mercedes-Benz G-Class2003 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11024620-0001.pdf↗
• October 20, 2025•Document ID: 11024406

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.70-P-079903

  Date Added:

  October 21, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Noise interference occurs during hands-free phone calls. Cause The interference is due to electromagnetic compatibility (EMC) faults affecting the microphone wiring. This disrupts signal integrity and degrades voice quality. Severity may vary by vehicle configuration. Remedy A corrective measure involving modified wiring harnesses and revised microphone connections is in development. The updated solution is scheduled for release in December 2025. Once the measure is implemented, this bulletin will be updated and versioned accordingly.

  Associated Products (1)

  2025 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11024406-0001.pdf↗
• October 20, 2025•Document ID: 11024405

  Service Bulletin/Repair Instructions
  SERVICE BRAKES

  Mfr Comm. #:

  LI42.10-P-079904

  Date Added:

  October 21, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint At low speeds and light brake pressure, brakes will make a groaning or honking noise. Cause Frictional vibrations with very light brake pressure/modulations. Remedy This condition can be duplicated on most vehicles. To validate, use a like for like reference vehicle. The noise is normal behavior under the conditions listed. With very light brake pressure this noise can be induced/caused due to normal brake pad and brake rotor vibrations. Exchanging brake components will not rectify.

  Associated Products (98)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class+ 78 more
  Associated Documents

  • DownloadMC-11024405-0001.pdf↗
• October 10, 2025•Document ID: 11024274

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.62-P-078631

  Date Added:

  October 14, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Note: In this case, do not use the damage codes for the speakers in the warranty claim.

  Associated Products (53)

  2026 Mercedes-Benz CLA-Class2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class+ 33 more
  Associated Documents

  • DownloadMC-11024274-0001.pdf↗
• September 25, 2025•Document ID: 11023347

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.10-P-071499

  Date Added:

  September 25, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint The result from the XENTRY battery test does not match the current state of the battery. Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy 1) If the battery is discharged, charge the battery. Review WS54.00-P-0037B for minimum charger specifications. • Note the amperage difference between trickle (maintainer) chargers of at least 16A and quick chargers of at least 30A. • Review AP54.10-P-5449U. Note when battery is sufficiently charged the charger current is less 5A. 2) While charging the battery, analyze the vehicle data to determine root cause of discharge using the following data points: • NOTE: For guidance on use of the on-board electrical data please review the AKUBIS video titled "New onboard electrical system diagnosis shown on BR 166". The video can be accessed through WIS by following the path WSM--> content by model series --> passenger cars --> ML-Class --> Model 166 --> group 54 --> New onboard electrical system diagnosis. • Refer to the March 2023 PCTT for the video walkthrough of analysis as well as the attachment of the slides to this Li. • Review GF54.10-P-1012A regarding what can cause deep discharge protection to not end a battery draw. • Review SI54.10-P-0024A for proper maintenance of the vehicle. For Star 2 vehicles: -Review FSAM on-board electrical data conspicuous records • NOTE: This data can be found via FSAM N10/6 -> Actual Values -> On-board electrical system -> On-board electrical system data For Star 3 vehicles: -Review N73/3 EZS on-board electrical data conspicuous records • NOTE: This data can be found via EZS N73/3 -> Actual Values -> On-board electrical system -> On-board electrical system data 3) Determine if root cause is due to: • vehicle technical issue? • customer behavior? NOTE: Recommend using battery analysis sheet found in XiW -> Local Contents -> Diagnostic info -> Battery Discharge Worksheet 4) If battery still does not accept charge AND the vehicle does not fall within the parameters of improper maintenance, then create a TIPS case. *IMPORTANT* - If the improper maintenance/use is found during diagnosis, DO NOT open a TIPS case. If a TIPS case is opened, it will be marked 1 star and directed to your assigned FSE for review. TIPS Case must include with the case: • Amperage setting of charger and time battery was on charger • XENTRY Battery Tester results • Voltage of battery taken with multimeter: Do not connect charger while taking measurements • N10/6 FSAM, (N73 or N73/3) and (N73*1 or N73/3*1) • Workshop analysis of conspicuous data • Root cause analysis for battery discharge based on the above documents (technical, customer, etc.) • NOTE: For expedited results when creating a case write customer complaint as "XENTRY Battery Tester implausible".

  Associated Products (114)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLC-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE+ 94 more
  Associated Documents

  • DownloadMC-11023347-0001.pdf↗
• September 17, 2025•Document ID: 11023193

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI27.19-P-072588

  Date Added:

  September 18, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy For vehicles with 722.9 transmission: Ensure LI54.15-P-057373 is performed before replacing any component parts. After processing and complying with the above document(s): 1. Perform an ignition reset on Y3/8n4 (VGS) 2. Inspect transmission connector for loose connections, damaged wiring or pins and any other concerns If communication with the VGS cannot be established, the complete valve body ('electrohydraulic controller unit (EHS)') must be replaced. Installation of a VGS repair kit is not permitted in this case as it is not possible to transfer the necessary valve characteristics without communication with the original control unit.

  Associated Products (143)

  2026 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class+ 123 more
  Associated Documents

  • DownloadMC-11023193-0001.pdf↗
• September 16, 2025•Document ID: 11023154

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.10-P-079533

  Date Added:

  September 17, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint 243: Red 12V battery message, white HV warning message, warning message in the IC and if applicable for vehicles with BMS30EB02 yellow HV drive system 465: Red 12V battery message, white HV warning message, warning message in the IC If the initial warning messages are ignored in the same ignition cycle, additional warning messages, e.g. red HV warning message and yellow HV drive system warning message may be shown. The DC/DC converter has stored a combination of the following two fault code groups: 1. P0C3B00, P0E9700, P0E5400, P0C4000. 2. P1D0B00, P1CA000, U011500. In some cases, not all DTCs from one of these groups are triggered. 243: As a consequence, on vehicles with BMS30EB02, the DTC for the auxiliary assembly fuse P0E2F00 can be set. This triggers the yellow HV drive system warning message. In the ignition cycle in which the red 12 V fault message is displayed, the DC/DC converter does not support the 12 V on-board electrical system. This means the 12 V battery may be discharged in the event of longer use. Cause In individual ignition cycles, this may result in faulty wake-up behavior of the DC/DC converter. The DCDC DTCs and warning messages may appear with a time delay. When accessing the vehicle, the white (243/465) HV warning message is displayed. When the HV system is switched on (charging, 12V supports, precon, ignition on), the yellow HV drive system warning message is displayed on the 243 with BMS30EB02 (see below for details). When the vehicle is started/PT-ready (displayed in the IC), the red 12V battery warning message is displayed for 243 and 465. Since the BMS on 243 uses the HV voltage value to check the auxiliary assembly fuse, the auxiliary assembly DTC can (with BMS30EB02) be stored as a consequence and the second (yellow) HV drive system warning message can be displayed in the IC. Remedy The faulty state of the DC/DC converter can always be rectified with an ignition change with BUS idle. The fact that the red 12 V warning message does not appear again is an indication of this. On vehicles with the yellow hybrid drive system message, it is still displayed because it is not automatically reset once the faulty state is reset. Check the DC/DC converter for functionality via Xentry Diagnostics in the workshop: • Actuate BUCK mode for approx. 30 s • The output current normally jumps to a high value (e.g. 100 A) and then falls slowly to the current specified value e.g. 50 A and then only changes slowly and in small increments. 243 EB311/312 (BMS30EB01): Perform reset of the DC/DC converter, e.g. through a BUS idle or by clearing the fault memory, to exit the faulty state. 243 EB330 (BMS30EB02): Clear the fault memory, since the DTC for the auxiliary assembly fuse and the yellow hybrid drive system warning message are not automatically reset. 465: Perform reset of the DC/DC converter, e.g. through a BUS idle or by clearing the fault memory, to exit the faulty state. !!! Important note: Problems in this area do not have to be invoiced on the damage code for the DC/DC converter 54720. !!! Information: Cause analysis is still ongoing in order to determine a long-term remedy. In cases in which the fault profile occurs multiple times, replacement of the DC/DC converter can be carried out. This may help delay the fault profile from reoccurring.

  Associated Products (5)

  2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2024 Mercedes-Benz EQB-Class2023 Mercedes-Benz EQB-Class2022 Mercedes-Benz EQB-Class
  Associated Documents

  • DownloadMC-11023154-0001.pdf↗
• August 15, 2025•Document ID: 11022058

  Service Bulletin/Repair Instructions
  ENGINE

  Mfr Comm. #:

  LI09.10-P-079599

  Date Added:

  August 21, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Check engine light illuminated. Fording not available message in instrument cluster. Fault code stored - P153073 Left air flap 'Air intake" has a malfunction. Cause Flap sticking inside air duct of cold air intake Remedy Replace air duct segment of cold air intake. Clear fault codes and check for any further symptoms.

  Associated Products (2)

  2025 Mercedes-Benz G-Class2024 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11022058-0001.pdf↗
• August 14, 2025•Document ID: 11021966

  Service Bulletin/Repair Instructions
  STEERING

  Mfr Comm. #:

  LI46.15-P-076223

  Date Added:

  August 18, 2025

  Manufacturer:

  MERCEDES BENZ

  Summary

  Complaint: Creaking or humming noise during adjustment of the electric steering column, see video. Cause: The noises occur due to insufficient greasing of the steering column adjustment guide. Remedy: Disassemble bellows of steering column tube module. Move steering column entirely out and entirely down. Grease steering column on green-marked positions with a suitable brush (find pictures in attachment). Move column up 1/4 of the way and grease again. Continue until upper limit stop is reached. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. If noise does not resolve, perform above procedure again. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. If noise still does not resolve, please open a TIPS case.

  Associated Products (14)

  2024 Mercedes-Benz G-Class2023 Mercedes-Benz G-Class2022 Mercedes-Benz G-Class2021 Mercedes-Benz G-Class2020 Mercedes-Benz G-Class2019 Mercedes-Benz G-Class2018 Mercedes-Benz G-Class2017 Mercedes-Benz G-Class2016 Mercedes-Benz G-Class2015 Mercedes-Benz G-Class2014 Mercedes-Benz G-Class2013 Mercedes-Benz G-Class2011 Mercedes-Benz G-Class2010 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11021966-0001.pdf↗
• August 8, 2025•Document ID: 11021800

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.10-P-079533

  Date Added:

  August 12, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint: 243: Red 12V battery message, white HV warning message, warning message in the IC ​​and if applicable for vehicles with BMS30EB02 yellow HV drive system 465: Red 12V battery message, white HV warning message, warning message in the IC If the initial warning messages are ignored, additional further warning messages (e.g. red HV warning message and yellow HV drive system warning message) are displayed. The DC/DC converter has saved the four following fault codes at most: P0C3B00, P0E9700, P0E5400, P0C4000. In some cases, not all of these DTCs are triggered. The following DTCs either be triggered additionally or, in rare cases, without the previous DTCs: P1D0B00, P1CA000, U011500. 243: As a consequence, on vehicles with BMS30EB02, the DTC for the auxiliary assembly fuse P0E2F00 can be set. That triggers the yellow HV drive system warning message. Cause: This may result in incorrect wake-up behavior of the DC/DC converter. The DCDC DTCs and warning messages may appear with a time delay. When accessing the vehicle, the white (243/465) HV warning message is displayed. When the HV system is switched on (charging, 12V supports, precon, ignition on), the yellow HV drive system warning message is displayed on the 243 with BMS30EB02 (see below for details). When the vehicle is started/PT-ready (displayed in the IC), the red 12V battery warning message is displayed for 243 and 465. Since the BMS on 243 uses the HV voltage value to check the auxiliary assembly fuse, the auxiliary assembly DTC can (with BMS30EB02) be stored and the second (yellow) HV drive system warning message can be displayed in the IC. Remedy: Check of the DC/DC converter via XENTRY Diagnosis Actuate BUCK mode for approx. 30 s The output current normally jumps to a high value (e.g. 100 A) and then falls slowly to the current specified value e.g. 50 A and then only changes slowly and in small increments. 243 EB330 (BMS30EB02):Clear the fault memory, since the DTC for the auxiliary assembly fuse and the yellow hybrid drive system warning message can only be reset in this way. 465:Perform a reset of the DC/DC converter, e.g. through a BUS idle or by clearing the fault memory, to exit the error state. Information: Cause analysis is still ongoing in order to determine a long-term remedy. In cases in which the fault profile occurs multiple times, please open a TIPS case.

  Associated Products (5)

  2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2024 Mercedes-Benz EQB-Class2023 Mercedes-Benz EQB-Class2022 Mercedes-Benz EQB-Class
  Associated Documents

  • DownloadMC-11021800-0001.pdf↗
• August 5, 2025•Document ID: 11021970

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.10-P-079533

  Date Added:

  August 19, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint: 243: Red 12V battery message, white HV warning message, warning message in the IC ​​and if applicable for vehicles with BMS30EB02 yellow HV drive system 465: Red 12V battery message, white HV warning message, warning message in the IC If the initial warning messages are ignored, additional further warning messages (e.g. red HV warning message and yellow HV drive system warning message) are displayed. The DC/DC converter has saved the four following fault codes at most: P0C3B00, P0E9700, P0E5400, P0C4000. In some cases, not all of these DTCs are triggered. The following DTCs either be triggered additionally or, in rare cases, without the previous DTCs: P1D0B00, P1CA000, U011500. 243: As a consequence, on vehicles with BMS30EB02, the DTC for the auxiliary assembly fuse P0E2F00 can be set. That triggers the yellow HV drive system warning message. Cause: This may result in incorrect wake-up behavior of the DC/DC converter. The DCDC DTCs and warning messages may appear with a time delay. When accessing the vehicle, the white (243/465) HV warning message is displayed. When the HV system is switched on (charging, 12V supports, precon, ignition on), the yellow HV drive system warning message is displayed on the 243 with BMS30EB02 (see below for details). When the vehicle is started/PT-ready (displayed in the IC), the red 12V battery warning message is displayed for 243 and 465. Since the BMS on 243 uses the HV voltage value to check the auxiliary assembly fuse, the auxiliary assembly DTC can (with BMS30EB02) be stored and the second (yellow) HV drive system warning message can be displayed in the IC. Remedy: Check of the DC/DC converter via XENTRY Diagnosis Actuate BUCK mode for approx. 30 s The output current normally jumps to a high value (e.g. 100 A) and then falls slowly to the current specified value e.g. 50 A and then only changes slowly and in small increments. 243 EB330 (BMS30EB02): Clear the fault memory, since the DTC for the auxiliary assembly fuse and the yellow hybrid drive system warning message can only be reset in this way. 465: Perform a reset of the DC/DC converter, e.g. through a BUS idle or by clearing the fault memory, to exit the error state. Information: Cause analysis is still ongoing in order to determine a long-term remedy. In cases in which the fault profile occurs multiple times, please open a TIPS case.

  Associated Products (5)

  2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2024 Mercedes-Benz EQB-Class2023 Mercedes-Benz EQB-Class2022 Mercedes-Benz EQB-Class
  Associated Documents

  • DownloadMC-11021970-0001.pdf↗
• August 5, 2025•Document ID: 11021898

  Service Bulletin/Repair Instructions
  STRUCTURE:BODY

  Mfr Comm. #:

  LI72.10-P-079446

  Date Added:

  August 15, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint: Customer complaint concerns wind/clattering noises upwards of 20mph in the area of the A-pillar, the outside mirror or at the front doors (cf. attachment). Cause: Cover trim on the underside of the outside mirror. Remedy: For troubleshooting, mask off the cover trim on the underside of the outside mirror (see attachment) and perform a test drive. If the problem can no longer be perceived, seal the cover trim with a butyl/sealing cord or replace if necessary.

  Associated Products (6)

  2024 Mercedes-Benz G-Class2023 Mercedes-Benz G-Class2022 Mercedes-Benz G-Class2021 Mercedes-Benz G-Class2020 Mercedes-Benz G-Class2019 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11021898-0001.pdf↗
• July 25, 2025•Document ID: 11021141

  Service Bulletin/Repair Instructions
  SERVICE BRAKES

  Mfr Comm. #:

  LI42.10-P-063502

  Date Added:

  August 1, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy The intent of this document is to reduce or eliminate noise from high performance AMG brakes. AMG brakes are designed for performance under high load and in certain scenarios, can emit noise. Some of the scenarios are: • Driving style • Brake pressure and application style (stop-and-go traffic with consistent low brake pressure “riding brakes” where the brakes cannot cool sufficiently between applications). • Ambient temperatures 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. Continue with applying chamfer and brake paste as instructed below. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! a) If the noises are coming from the front axle. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining backing plate, including the brake lining guide pins and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". If adhesive is already installed on backing plate, you may gently scrape off and re-apply a new adhesive. In some instances the adhesive may be very carefully removed and Molykote applied instead. 4. Chamfer edges (gently round off sharp leading edges) on brake pads. Some pads have vertical grooves, these can be gently chamfered with a triangular file as well. See picture "Chamfering Technique". 5. Apply Molykote to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 6. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle. 1. Remove brake pads of rear axle. 2. Clean all contact points on brake lining backing plate and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfering Technique". 5. Grease contact points (red areas on attachment "Rear Pad Grease Area") between brake lining and guide of brake caliper with Molykote. 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off recouperation prior to bedding in brakes. d) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. e) Finally drive approx. 3 miles to allow the system to cool. f) Reassess noise.

  Associated Products (122)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class+ 102 more
  Associated Documents

  • DownloadMC-11021141-0001.pdf↗
• July 16, 2025•Document ID: 11020872

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI27.19-P-074985

  Date Added:

  July 24, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Commissioning not possible after replacement of TRANSMISSION 722.9 or of electrohydraulic controller unit (EHS) or of repair kit controller unit (VGS). Cause The wrong older A-code ("Generation EHS") is documented in VeDoc for the newly installed transmission or the newly installed electrohydraulic controller unit (EHS)/repair kit controller unit (VGS). Old VGS2 hardware A0335457332 (from quick test) New VGS3 hardware A0034460310 or A0009018008 (from quick test) Remedy Delete the old A-code and redocument the new A-code in VeDoc, then perform commissioning. A. If Diagnosis at the vehicle is possible: To determine the correct EHS item number, the currently installed EHS/VGS hardware should be read out first: In XENTRY Diagnostics via the tab "Control unit view" - "Current quick test" - "Fully integrated transmission control" - "EHS part number". Order the new EHS with this read-off item number. DAS: "Quick test" - "EGS - Electronic transmission control serial number". Order the new EHS with this read-off serial number. B. If Diagnosis at the vehicle is no longer possible, The number must be read off directly from the EHS, and the ordering process must be initiated using this number. Exception: For engine 629 with transmission 722.9, EHS A220 270 24 06 must be installed. Read-off part number is A 220 270 12 06 In this case, the following must be observed for making a correct order: Exclusively for model 219.356, 171.456 with transmission 722.906 up to and including model year 2005 (code 805) A 220 270 12 06 is no longer available --> Please install EHS A220 270 27 06 and document A92 in Vedoc If this does not work, please open a TIPS case and provide both the original EHS part number/A code and new EHS part number/A code Read-off part number + old A-code in VeDoc --> EHS item number and new A-code ("Generation EHS") J valve body plate with VGS3 old A-code A28/A29: A2202701306 + code A28/A29 --> A2202702706, delete code A28/A29 and document A92 in VeDoc A2202701406 + code A28/A29 --> A2202702706, delete code A28/A29 and document A92 in VeDoc A2202701206 + code A28/A29 --> A2202702706 delete code A28/A29 and document A92 in VeDoc O valve body plate with VGS3 old A-code A45: A2202701206 + code A45 --> A2202702906, delete code A45 and document A94 in VeDoc A2202701406 + code A45 --> A2202702906, delete code A45 and document A94 in VeDoc A2202702106 + code A45 --> A2202702906, delete code A45 and document A94 in VeDoc P valve body plate with VGS3 old A-code A46: A2202701906 + code A46 --> A2202703006, delete code A46 and document A97 in VeDoc A2202702206 + code A46 --> A2202703006, delete code A46 and document A97 in VeDoc N valve body plate with VGS3 old A-code A39: A2202701206 + code A39 --> A2202703106, delete code A39 and document A95 in VeDoc A2202701406 + code A39 --> A2202703106, delete code A39 and document A95 in VeDoc A2202701806 + code A39 --> A2202703106, delete code A39 and document A95 in VeDoc M valve body plate with VGS3 old A-code A38: A2202701406 + code A38 --> A2202703206, delete code A38 and document A96 in VeDoc A2202701906 + code A38 --> A2202703206, delete code A38 and document A96 in VeDoc K valve body plate VGS3 with old A-code A30: Old A-code A30 --> delete code A30 and document A93 in VeDoc N valve body plate VGS3 with old A-code A27: Old A-code A27 --> delete code A27 and document A95 in VeDoc

  Associated Products (83)

  2020 Mercedes-Benz S-Class2019 Mercedes-Benz GLE-Class2019 Mercedes-Benz GLS-Class2019 Mercedes-Benz S-Class2019 Mercedes-Benz SL-Class2018 Mercedes-Benz C-Class2018 Mercedes-Benz G-Class2018 Mercedes-Benz GLE-Class2018 Mercedes-Benz GLS-Class2018 Mercedes-Benz S-Class2018 Mercedes-Benz SL-Class2017 Mercedes-Benz C-Class2017 Mercedes-Benz E-Class2017 Mercedes-Benz G-Class2017 Mercedes-Benz GLE-Class2017 Mercedes-Benz GLS-Class2017 Mercedes-Benz S-Class2017 Mercedes-Benz SL-Class2016 Mercedes-Benz C-Class2016 Mercedes-Benz CLS-Class+ 63 more
  Associated Documents

  • DownloadMC-11020872-0001.pdf↗