Nissan Murano Service Bulletins
113 manufacturer communications on file.
- May 1, 2026•Document ID: 11033026Service Bulletin/Repair InstructionsFUEL/PROPULSION SYSTEM
- Mfr Comm. #:
- NTB26-006A
- Date Added:
- May 30, 2026
- Manufacturer:
- NISSAN
SummaryFUEL FILLER TUBE LOWER SEAL IS LEAKING AND DTC P0456 IS STORED IN THE ECM This bulletin is no longer active. Please discard previous versions of NTB26-006.
Associated Products (14)Associated Documents - April 15, 2026•Document ID: 11031721Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- NTB26-019
- Date Added:
- April 29, 2026
- Manufacturer:
- NISSAN
SummaryMIL ON WITH DTC P0181 STORED IN THE ECM IF YOU CONFIRM The customer states the MIL is ON but the vehicle does not have any drivability concerns or reduced power message in the combination meter, AND DTC P0181 for “Fuel Tank Temperature” is stored in either “Past” or “Current” in the ECM. ACTION Follow the SERVICE PROCEDURE in this bulletin to: 1. Replace the fuel temperature sensor. 2. Erase all the DTCs.
Associated Products (7)Associated Documents - April 13, 2026•Document ID: 11031705Service Bulletin/Repair InstructionsSTRUCTURE:BODY
- Mfr Comm. #:
- NTB09-131C
- Date Added:
- April 29, 2026
- Manufacturer:
- NISSAN
SummaryCERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
Associated Products (72)2026 Nissan Altima2026 Nissan Armada2026 Nissan Frontier2026 Nissan Leaf2026 Nissan Murano2026 Nissan Pathfinder2026 Nissan Rogue2026 Nissan Sentra2025 Nissan Altima2025 Nissan Armada2025 Nissan Frontier2025 Nissan Leaf2025 Nissan Murano2025 Nissan Pathfinder2025 Nissan Rogue2025 Nissan Sentra2025 Nissan Versa2024 Nissan Altima2024 Nissan Armada2024 Nissan Frontier+ 52 moreAssociated Documents - April 13, 2026•Document ID: 11031704Service Bulletin/Repair InstructionsSTRUCTURE:BODY
- Mfr Comm. #:
- NTB09-131C
- Date Added:
- April 29, 2026
- Manufacturer:
- NISSAN
SummaryCERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
Associated Products (72)2026 Nissan Altima2026 Nissan Armada2026 Nissan Frontier2026 Nissan Leaf2026 Nissan Murano2026 Nissan Pathfinder2026 Nissan Rogue2026 Nissan Sentra2025 Nissan Altima2025 Nissan Armada2025 Nissan Frontier2025 Nissan Leaf2025 Nissan Murano2025 Nissan Pathfinder2025 Nissan Rogue2025 Nissan Sentra2025 Nissan Versa2024 Nissan Altima2024 Nissan Armada2024 Nissan Frontier+ 52 moreAssociated Documents - April 9, 2026•Document ID: 11031702Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- NTB26-017
- Date Added:
- April 29, 2026
- Manufacturer:
- NISSAN
SummaryENGINE NO START WITH KEY SYSTEM ERROR AND DTC B2C20-24 STORED IN THE BCM IF YOU CONFIRM The customer states the engine will not start and “Key System Error” warning is displaying in the Information Display (Combination Meter) (Figure 1), AND DTC B2C20-24 for "STARTER CONTROL RELAY" is stored in the BCM. Figure 1 HINT: This DTC and warning message (Figure 1) may occur if the customer does not place the vehicle in Park Gear according to the Owner’s Manual for shifter operation. ACTION 1. Confirm the current ECM part number. 2. Confirm the current TCM part number. 3. Reprogram the ECM, and then the TCM, if applicable. 4. Erase the DTCs. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
Associated Products (1)Associated Documents - March 30, 2026•Document ID: 11031699Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- NTB15-049CC
- Date Added:
- April 29, 2026
- Manufacturer:
- NISSAN
SummaryTELEMATICS SERVICE INFORMATION HINT: This bulletin applies to vehicles equipped with a 4G network compatible TCU. TCUs compatible with 3G network only are no longer supported. SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnect® Services subscription, the TCU communicates with the NissanConnect® Services Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the APPLIED VEHICLES. · A table has been provided on the next page that lists the steps required to successfully configure a TCU after it has been replaced. · A CHECK-OFF SHEET has been provided on page 20 to print and check off steps as they are performed. Staple the completed CHECK-OFF SHEET to the repair order.
Associated Products (16)Associated Documents - February 2, 2026•Document ID: 11028683Service Bulletin/Repair InstructionsFUEL/PROPULSION SYSTEM
- Mfr Comm. #:
- NTB26-006
- Date Added:
- February 10, 2026
- Manufacturer:
- NISSAN
SummaryFUEL FILLER TUBE LOWER SEAL IS LEAKING AND DTC P0456 IS STORED IN THE ECM IF YOU CONFIRM The vehicle has a visible leak with a smoke machine test coming from the fuel filler tube lower seal, AND DTC P0456 is stored as “Active”, “Past”, or “Pending” in the ECM. ACTION 1. Remove the supplied funnel from the rear of the vehicle or trunk. 2. Insert the funnel completely in the fuel filler tube and remove completely five (5) times. 3. Re-check the fuel filler tube lower seal with a smoke machine to determine visually if any leak is present. 4. If the fuel filler lower seal continues to leak, replace the fuel filler tube. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
Associated Products (14)Associated Documents - January 7, 2026•Document ID: 11028691Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- NTB25-063
- Date Added:
- February 10, 2026
- Manufacturer:
- NISSAN
SummaryVENT CONTROL VALVE IN ACTIVE TEST INOPERATIVE IN CONSULT 4 SERVICE INFORMATION An issue in CONSULT 4 has been identified in “EVAP system close” in Work support. · After selecting the "EVAP system close" in Work support, the “VENT CONTROL/V” in Active test becomes non-functional temporarily. · When selecting “EVAP system close” operation in Work support, wait 10 minutes before starting “VENT CONTROL/V” Active test or cycle the IGN switch ON/OFF for “VENT CONTROL/V” Active test to be operational. HINT: This bulletin applies to model years that use CONSULT 4 only.
Associated Products (8)Associated Documents - October 1, 2025•Document ID: 11024391Service Bulletin/Repair InstructionsSTRUCTURE:BODY
- Mfr Comm. #:
- NPSB 15-460
- Date Added:
- October 21, 2025
- Manufacturer:
- NISSAN
SummaryACTION Date: October 2, 2025 To: FOMs, DOMs, RAMs, & RGMs Subject: LAUNCH PD172 PMA55 Multi Model Monroney Bumper Label – QA – Dealer Announcement and Procedure ACTION: FOMs & DOMs are asked to ensure that dealers are aware of this new campaign information. Dealer Announcement: To ensure continued customer satisfaction and confidence, Nissan is conducting a quality action on certain specific model year 2025 ARIYA, 2024-2025 Pathfinder, 2024-2026 Rogue, 2024-2025 Murano and 2025-2026 Kicks vehicles, as identified in Service Comm and DBS National Service History. This action updates the Monroney labels to reflect corrected bumper labeling requirements for California and Hawaii. Dealers will replace original Monroney labels with corrected Monroney labels. Nissan will send VIN-specific corrected labels to address affected vehicles in dealer inventory. New labels will begin shipping via Federal Express Wednesday, October 1, 2025. Dealers will replace original Monroney labels with corrected Monroney labels. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. What Dealers Should Do: PLEASE FOLLOW THE ATTACHED INSTRUCTIONS: 1.Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History – Open Campaigns I.D. PD172 & PMA55 •New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). Refer to NPSB 15-460 for additional information •Some vehicles may still be in transit. Please continue to check newly arriving inventory for applicability. 2.Please do not drive, loan, sell or trade the specific vehicles in dealer inventory subject to this quality action. 3.Use the attached procedure to remedy any vehicles affected by this quality action prior to sale. 4.If you have exchanged or traded one of the affected vehicles to another Nissan dealer, please forward the corrected Monroney label to the current dealer upon receipt so it can be attached to the vehicle. •If a vehicle has been retailed, dispose of the corrected Monroney label using the same procedure as for destroying the original Monroney label. 5.The service department should submit the applicable warranty claim for the action performed to close the campaign in Service Comm and release the vehicle.
Associated Products (6)Associated Documents - June 16, 2025•Document ID: 11019712Service Bulletin/Repair InstructionsSTRUCTURE:BODY
- Mfr Comm. #:
- NTB25-031
- Date Added:
- June 25, 2025
- Manufacturer:
- NISSAN
SummaryCLICKING NOISE WHEN OPENING DRIVER DOOR SERVICE INFORMATION If a popping / clicking noise is present from one or more of the Door Check Links (Figure 1) when opening the associated door: First confirm that the torque of the door side mounting bolts of the related Door Check Link is at the correct specification, and then retest for popping / clicking before considering replacing the Door Check Link. • Refer to the ESM: BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY - DOOR & LOCK - REMOVAL AND INSTALLATION - DOOR - DOOR CHECK LINK • There are two (2) door side mounting bolts per door and a total of eight (8) per vehicle.
Associated Products (1)Associated Documents - February 26, 2025•Document ID: 11015916Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- NTB25-013
- Date Added:
- March 25, 2025
- Manufacturer:
- NISSAN
SummaryECM REPLACEMENT PROCEDURE REQUIRED FOR RES EQUIPPED VEHICLES SERVICE INFORMATION If any of the APPLIED VEHICLES equipped with Remote Engine Start (RES) requires Engine Control Module (ECM) replacement, the Body Control Module (BCM) must be replaced also at the same time. If you are not familiar with the Re/programming, Configuration procedure, refer to the Electronic Service Manual (ESM) and the CONSULT Operation Manual to reprogram the Electronic Control Unit (ECU). Follow all precautions in both manuals to prevent possible personal injury or death and/or damage to the ECU. This procedure will go back and forth between the ECM and BCM steps as found in the ESM. Damage will occur requiring the ECM and the BCM to be replaced a second time if the following SERVICE PROCEDURE is not followed. Perform the following steps from the Electronic Service Manual (ESM) in this order: A. Perform “Work Procedure (Before Replacing ECM)” to save the ECM data. B. Remove the ECM. C. Remove the BCM. D. Install the new BCM and then perform “Additional Service When Replacing BCM - Work Procedure” up to and including “Register of Vehicle Identification Number”. E. Install the new ECM and then perform “Additional Service When Replacing ECM - Work Procedure (After Replacing ECM)” up to and including “Writing MAC Key for ECM”. F. Complete the “Additional Service When Replacing BCM - Work Procedure”. G. Complete the “Additional Service When Replacing ECM - Work Procedure (After Replacing ECM)”.
Associated Products (2)Associated Documents - February 20, 2025•Document ID: 11014472Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING; SERVICE BRAKES
- Mfr Comm. #:
- NTB19-042F
- Date Added:
- February 25, 2025
- Manufacturer:
- NISSAN
SummaryAUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera (see Figure 1) SERVICE INFORMATION If the Automatic Emergency Braking (AEB) warning light or is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: When contamination or foreign material adhere to the lane camera viewing window on the windshield. When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield. When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information: Refer to the following pages. Use the search keyword “blinking” in the ESM.
Associated Products (46)2024 Nissan Altima2024 Nissan Armada2024 Nissan Frontier2024 Nissan Kicks2024 Nissan Leaf2024 Nissan Murano2024 Nissan Pathfinder2024 Nissan Sentra2024 Nissan Titan2024 Nissan Versa2023 Nissan Altima2023 Nissan Armada2023 Nissan Frontier2023 Nissan Kicks2023 Nissan Leaf2023 Nissan Maxima2023 Nissan Murano2023 Nissan Pathfinder2023 Nissan Rogue2023 Nissan Sentra+ 26 moreAssociated Documents - February 20, 2025•Document ID: 11014471Service Bulletin/Repair InstructionsFORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL; ELECTRICAL SYSTEM; SERVICE BRAKES; FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING
- Mfr Comm. #:
- NTB19-033G
- Date Added:
- February 25, 2025
- Manufacturer:
- NISSAN
SummaryINTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
Associated Products (46)2024 Nissan Armada2024 Nissan Frontier2024 Nissan Kicks2024 Nissan Leaf2024 Nissan Murano2024 Nissan Pathfinder2024 Nissan Sentra2024 Nissan Titan2024 Nissan Versa2023 Nissan Altima2023 Nissan Armada2023 Nissan Frontier2023 Nissan Kicks2023 Nissan Leaf2023 Nissan Maxima2023 Nissan Murano2023 Nissan Pathfinder2023 Nissan Rogue2023 Nissan Sentra2023 Nissan Titan+ 26 moreAssociated Documents - February 18, 2025•Document ID: 11014475Service Bulletin/Repair InstructionsSTRUCTURE:BODY
- Mfr Comm. #:
- NTB25-011
- Date Added:
- February 25, 2025
- Manufacturer:
- NISSAN
SummaryLICENSE PLATE FRAME INTERFERENCE TO REAR BUMPER IF YOU CONFIRM A license plate frame does not sit flush and is making contact at bottom edge when installed to the Rear Bumper, as shown in Figure 1 and Figure 2. Figure 1 Figure 2 ACTION Refer to the SERVICE PROCEDURE in this bulletin to relocate the license plate mounting holes in the Rear Bumper. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
Associated Products (1)Associated Documents - October 4, 2024•Document ID: 11009069Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; LANE DEPARTURE: WARNING; LANE DEPARTURE: ASSIST
- Mfr Comm. #:
- NTB20-066C
- Date Added:
- October 22, 2024
- Manufacturer:
- NISSAN
SummaryLANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM SERVICE INFORMATION If the lane camera requires aiming, the values in Table A on page 4 must be used. For all other models/model years, consult the Electronic Service Manual (ESM).
Associated Products (4)Associated Documents - September 19, 2024•Document ID: 11009068Service Bulletin/Repair InstructionsAIR BAGS
- Mfr Comm. #:
- NTB19-071D
- Date Added:
- October 22, 2024
- Manufacturer:
- NISSAN
SummaryDTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)
Associated Products (48)2024 Nissan Altima2024 Nissan Armada2024 Nissan Frontier2024 Nissan Kicks2024 Nissan Leaf2024 Nissan Murano2024 Nissan Pathfinder2024 Nissan Rogue2024 Nissan Sentra2024 Nissan Titan2024 Nissan Versa2023 Nissan Altima2023 Nissan Armada2023 Nissan Frontier2023 Nissan Kicks2023 Nissan Leaf2023 Nissan Maxima2023 Nissan Murano2023 Nissan Pathfinder2023 Nissan Rogue+ 28 moreAssociated Documents - July 17, 2024•Document ID: 11007005Service Bulletin/Repair InstructionsFORWARD COLLISION AVOIDANCE: WARNINGS; SERVICE BRAKES
- Mfr Comm. #:
- NTB24-037
- Date Added:
- September 4, 2024
- Manufacturer:
- NISSAN
SummaryFALSE ACTIVATION OF AEB OR FCW APPLIED VEHICLES: 2019-2024 Murano (Z52) APPLIED SYSTEMS: Automatic Emergency Braking/Forward Collision Warning IF YOU CONFIRM The customer states they have experienced false activation and/or unexpected braking of the Automatic Emergency Braking (AEB) or Forward Collision Warning (FCW) system, AND There are no related DTCs stored. ACTION Refer to the SERVICE PROCEDURE in this bulletin to: 1. Confirm the current ICC/ADAS 2 part number. 2. Reprogram the ICC/ADAS 2, if applicable.
Associated Products (4)Associated Documents - June 7, 2024•Document ID: 11001192Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- NTB12-103I
- Date Added:
- June 7, 2024
- Manufacturer:
- NISSAN
SummaryCVT/TCM CALIBRATION DATA “WRITE” PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Associated Products (9)Associated Documents - May 21, 2024•Document ID: 11004963Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- NTB17-127C
- Date Added:
- July 19, 2024
- Manufacturer:
- NISSAN
SummaryINTELLIGENT KEY INITIALIZATION PROCEDURE STOPS OR WILL NOT CONTINUE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
Associated Products (15)Associated Documents - May 21, 2024•Document ID: 11004962Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- NTB13-107G
- Date Added:
- July 19, 2024
- Manufacturer:
- NISSAN
SummaryVEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Associated Products (45)2025 Nissan Leaf2024 Nissan Altima2024 Nissan Armada2024 Nissan Frontier2024 Nissan GT-R2024 Nissan Kicks2024 Nissan Leaf2024 Nissan Murano2024 Nissan Titan2024 Nissan Versa2023 Nissan Altima2023 Nissan Armada2023 Nissan Frontier2023 Nissan GT-R2023 Nissan Kicks2023 Nissan Leaf2023 Nissan Maxima2023 Nissan Murano2023 Nissan Titan2023 Nissan Versa+ 25 moreAssociated Documents