GMC Yukon XL Complaints

2,896 consumer complaints on file.

#11727406March 27, 2026
ENGINE AND ENGINE COOLING
The contact owns a 2023 GMC Yukon XL. The contact stated that the vehicle was losing oil, and the engine was running rough. There was an abnormal burning odor after driving the vehicle. The vehicle received an oil change; however, two weeks later, the oil warning light illuminated. The vehicle was towed to the local dealer, where it was determined the oil level was approximately 2 quarts low, and another oil change was performed. The vehicle was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was approximately 70,000.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11727058March 25, 2026
EXTERIOR LIGHTING
Yes, that case number would be 91762225 (With GM). You are most welcome. Thank you for contacting Chevrolet Customer Assistance and have a nice day! Please don’t hesitate to reach out if you need anything else. VIN1GKS2HKC8FR165487 Special Coverage Adjustment N182180270 Tail Lamps Inoperative Having issues described by NTSA and vehicle has 62,000 miles but falls after the expiration date. I contacted GM and they were very nice but they were unwilling to help in any way. Any help would be appreciated.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11727109March 25, 2026
ENGINE
I am submitting this complaint to report what I believe to be a serious and systemic safety defect involving GM 6.2L engines equipped with fuel efficiency systems such as Active Fuel Management (AFM) or Dynamic Fuel Management (DFM). I have experienced catastrophic engine failure in two separate GMC Yukon Denali vehicles with nearly identical symptoms, which strongly suggests a broader design defect rather than isolated mechanical issues. My first vehicle, a 2015 GMC Yukon Denali XL, developed significant engine performance problems consistent with known lifter and camshaft failures widely reported in GM vehicles using these fuel efficiency systems. Due to ongoing reliability concerns and the financial burden of potential repair, I was forced to trade this vehicle at a loss. My second vehicle, a 2016 GMC Yukon Denali XL equipped with the same engine platform, suffered sudden and catastrophic engine failure in February 2026. This failure occurred abruptly and without meaningful prior warning, rendering the vehicle inoperable and creating a potentially hazardous situation. Sudden engine failure of this nature presents a significant safety risk, particularly if it occurs at highway speeds or in heavy traffic. An oil service had been performed on this vehicle in December 2025 at a Jiffy Lube franchise. After the failure, an independent service provider documented that the oil fill cap had been left loose. However, the Jiffy Lube franchise and its insurance carrier have denied responsibility, asserting that the engine failure is attributable to known defects and reliability issues associated with GM’s fuel efficiency engine systems. As a result, both the manufacturer and the service provider are denying responsibility for a catastrophic mechanical failure that has serious safety implications. This leaves consumers exposed to sudden engine failure risk with no meaningful recourse. Based on my direct experience with two separate vehicles exhibiting similar catastroph
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11727117March 25, 2026
ENGINE
2021 Yukon Denali 6.2L V8, 137k miles- engine failure—driving down road 55mph and engine light came on, along with check esc and check traction warnings, vehicle began to rough idle and shake, motor knocking. Personally feel this is related to recall but my vin not included says dealership- I feel this recall is affecting way more vehicles than vin’s included. Dealership charged 220$ to plug it in, codes weren’t specific for problem. They are stating “lifter is bad and possibly cam, won’t know if the lifters scarred the cam until they take it apart” and charge me at least 6k is price quoted. No warnings at all before this happened. 137k miles so out of warranty. This put myself and kids in dangerous riding condition as I had to stop and have vehicle towed to dealership.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11727105March 25, 2026
ENGINE
2023 Yukon XL Denali passed the pico scope changed to 0W40 and 3 months later stopped working in the middle of driving just completely shut down. Engine started to smoke had it towed to dealership and they removed my oil filter and found crankshaft bearings in the filter. Needs a new engine now. Bought it brand new only has 45,000 miles on it currently.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11726283March 23, 2026
SERVICE BRAKES, HYDRAULIC, ENGINE
The contact owns a 2015 GMC Yukon XL. The contact stated that while driving 70 MPH and exiting the highway, the brake pedal was depressed but the brake pedal was stiff and stuck, requiring that the transmission be shifted to neutral(N), and to stand on the brake pedal with both feet. The contact continuously pumped the brake pedal, but the vehicle slowly responded and almost crashed into other vehicles. There was no warning light illuminated. The contact's wife and daughter were also inside the vehicle during the failure and were frightened and concerned for their safety during the failure. The dealer was contacted and was provided a description of the failure over the phone. The dealer informed the contact that the vacuum pump and an unknown part had possibly failed. The contact was advised that the failure was possibly related to NHTSA Campaign Number: 19V645000 (Service Brakes, Hydraulic); however, the VIN was not included in the recall, and there was no warranty coverage on the vehicle for the failure. Additionally, the check engine warning light was illuminated. The vehicle was not diagnosed or repaired due to the cost. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 143,000.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11726504March 23, 2026
SERVICE BRAKES
After pressing the brake pedal 2 or 3 times the pedal becomes very hard and it is extremely hard to stop the vehicle. All new brake pads and rotors. The brake pedal is loosing vacuum.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11726556March 23, 2026
ENGINE, FUEL/PROPULSION SYSTEM, POWER TRAIN
2023 GMC Yukon XL 6.2L V8 experienced progressive engine defects starting in first year. At 7,445 mi (Jan 2023), first dealer visit for engine issues. At 10,315 mi (Apr 2023), Cyl 2 fuel injector failed (internally open), vehicle TOWED to dealer, replaced under warranty. At 14,982 mi (Aug 2023), identical Cyl 7 injector failure (internally open), replaced under warranty. Two identical failures on different cylinders within 15,000 mi indicates systemic defect. By 30,409 mi (Aug 2024), dealer performed engine decarbonization due to carbon buildup from fuel injection issues. Dealer recommended additional decarbs at 38,077 mi and 42,577 mi. At 56,028 mi (Mar 2026), engine suffered catastrophic failure: piston ring failure causing excessive oil consumption and engine destruction, requiring full engine replacement. This matches GM's known 5.3L/6.2L V8 piston ring defect (subject of $150M class action settlement). Defective injectors caused incomplete combustion, carbon buildup on piston rings, ring tension loss, and catastrophic engine failure. Vehicle also has unfixed suspension defect (camber bolt/alignment). Vehicle visited dealer 8+ times. Engine failure poses serious safety risk from sudden power loss at highway speeds. Vehicle available for inspection.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11726355March 23, 2026
ENGINE, LANE DEPARTURE: BLIND SPOT DETECTION, ELECTRICAL SYSTEM
This is a Post-Remedy Failure of Recall 25V-274 (GMC 6.2L L87 Engine). Following a full engine replacement performed by the dealer under this safety recall, the vehicle has suffered a catastrophic electrical compromise. The vehicle is currently throwing codes P2534 (Low Ignition Voltage) and U3018 (BCM Communication). Safety Hazards: The vehicle experiences sudden loss of power, engine stalling at highway speeds, and total failure of the exterior turn signals (hyper-flash). The AC system has been disabled by the Body Control Module due to low voltage, creating a hazard in high temperatures. This vehicle fits the exact profile of NHTSA Recall Query RQ26-001 and Engineering Analysis EA25-007. The manufacturer's remedy for the safety recall has failed to restore the vehicle to a safe operating condition, and the dealership is attempting to charge diagnostic fees to investigate their own defective recall workmanship.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11726253March 23, 2026
ENGINE
Im hearing ticking sounds when starting the engine and I reported it to my dealership service department and thay said thay don't see any issue
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11726127March 22, 2026
STEERING
Driving on the highway when the steering warning light came on and then I had a loss of complete steering on the highway. Somehow was able to get off the highway but not completely off the road. Back end of the vehicle was still in harms way I could not turn that wheel at all this is a complete safety issue and could have easily caused an accident and could have been deadly. There was no warning before that just went out while driving at highway speeds on the highway. Also had to wait two hours for a tow. Vehicle is currently being diagnosed at the dealer and will provide all receipts once completed. This is an issue that needs to be addressed. Huge safety concen
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11726235March 22, 2026
FUEL/PROPULSION SYSTEM
Engine stalling, a rough-running engine, reduced power mode (sluggish acceleration), a "Check Engine" light, or the vehicle failing to start. It started puttering really bad and died in the middle of the intersection. Check engine light came on. I got it to start, was really hard start and puttered bad then it died again and then I got it to start again, was a really hard start and puttered and died again. I was able to start it again get in the driveway but couldn’t go very fast. Check engine codes present are P2635 and P018B
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11726046March 21, 2026
ENGINE
Lifters broke and destroyed the camshaft at 99,000 miles. Total repair cost $8,200.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11726102March 21, 2026
ENGINE
Engine failed, no check engine lights turned on. Needed to have the truck towed to a dealer
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11725724March 19, 2026
POWER TRAIN
Transfercase was casuing the Yukon to serge when in auto mode. No codes warning lights were presented. The dealer did not find any codes but when the transfer case was removed the oil was drained to which metal shavings were found in the oil. After getting the Yukon back the transmission began to exibit the same type of issues. Currently the Yukon is back in the shop.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11725722March 19, 2026
POWER TRAIN, FUEL/PROPULSION SYSTEM
High pressure fuel pump housing failed and filled the cabin with fumes. Rendered the the Yukon unsafe to drive with fuel flooding the engine compartment. Took the dealer 57 days to repair the car. No warning lights, only indication was the fumes in the cabin.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11725570March 19, 2026
ENGINE
engine failure from the connecting rod and/or crankshaft. There is a current recall for this and my vehicle should be a part of it. I broke down on the side of a highway and had the vehicle towed to GMC dealership. There are now warning lights on with code P0016 and P0324
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11725564March 19, 2026
ENGINE
2026 GMC Yukon XL Denali, VIN [XXX] , 6.2L V8 L87 engine. At 3,168 miles, vehicle developed rough idle and knocking noise. Delivered to Sewell Buick GMC Dallas on 3/2/26. Dealer diagnosed crankshaft thrust bearing spun. Tech pinpointed bottom-end noise via stethoscope, found excessive metal debris in oil and oil filter. Engine teardown confirmed thrust bearing failure. Required complete engine replacement (GM #xxx), plus oil cooler/radiator, oil cooler lines, torque converter bolts, and all one-time-use parts due to metal contamination. Old engine serial [XXX] , new engine [XXX] . Repaired under warranty 3/9/26, RO #XXX. This is the identical failure mode that caused NHTSA Recall 25V-274 covering ~597,630 L87-equipped vehicles (MY 2021-2024). GM stated manufacturing improvements were completed by 6/1/24 and 2025+ models were not affected. My 2026 model year failure directly contradicts this claim and suggests the defect persists in current production. SAFETY CONCERN: Bearing failure causes sudden complete loss of propulsion at any speed. NHTSA investigation PE25001 notes most failures occur without warning. Loss of power at highway speed creates serious crash risk due to loss of ability to accelerate and reduced power braking/steering. Had this failure progressed further while driving with my family, consequences could have been severe. No crash or injury occurred in this instance. This 2026 model year failure indicates NHTSA's investigation scope should expand to include current production vehicles. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11725128March 18, 2026
ENGINE
P0304 and P0306 misfiring and compression on both cylinders is 0. Both lifters have broke and collapsed. It started with a noise, once checked by the mechanic, we were told the lifter was going bad, before we could get it repaired it completely broke and that is when the check engine light came on and went off repeated times. At this time it is pouring out black smoke when driving and must have a complete engine replacement. The replacement work has been quoted for $10479.57.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11725011March 17, 2026
ENGINE
After getting the engine recall done on my vehicle over 6 months ago, I was driving down the highway at 70 mph last Saturday and without warning "Press Start" began flashing on my dashboard and I immediately began decelerating and my car put itself in Neutral. I was able to get to the side of the road safely. I was then able to turn the car off and back on. I was able to again accelerate into the road but once I reached 3/4th gear my car again began beeping with the "Press Start" warning and put itself into neutral. I was again able to coast on the side of the road to a stop where I called a tow truck to drop at my local GMC dealer. When roadside assistance showed up the car wouldn't even turn on anymore and I'm now being told that I need a full engine replacement even though I correctly completed the recall previously.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0

← Back to GMC Yukon XL