BMW 325xi Service Bulletins
123 manufacturer communications on file.
- May 1, 2016•Document ID: 10151300Service Bulletin/Repair InstructionsENGINE; EQUIPMENT
- Mfr Comm. #:
- B110616
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryN51, N52, N52K and N52T Engines: Various Eccentric Shaft Sensor Faults stored in the DME - Diagnostic Hints This Service Information bulletin and attachment supersedes SI B11 06 16 dated April 2016.. The customer may complain about one of the following: Rough engine running Engine cannot be started (crank no start) Check Engine Light illuminated One or more of the following faults may be stored in the DME: 2A37 - Valvetronic, eccentric shaft sensor plausibility 2A47 - Valvetronic, eccentric shaft, signal plausibility 134E08 - Eccentric shaft plausibility (on F10, F25 vehicles only) CAUSE The VVT eccentric shaft sensor connector, and/or DME connector may have oil contamination due to oil leakage at the VVT sensor gasket.
Associated Products (50)Associated Documents - April 1, 2016•Document ID: 10151255Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EQUIPMENT
- Mfr Comm. #:
- B121116
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryISTA/P Cannot Program an E-Series N55 Replacement DME. ISTA/P fails when attempting to program a replacement DME (MEVD172) on BN2000 E-Series vehicles with the Continental HPP. Part number: 12 14 8 618 483. DME logistic error between the replacement hardware and basic software prevents correct programming with ISTA/P.
Associated Products (45)Associated Documents - April 1, 2016•Document ID: 10151247Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- B110616
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryN51, N52, N52K and N52T Engines: Various Eccentric Shaft Sensor Faults stored in the DME - Diagnostic Hints. The customer may complain about one of the following: Rough engine running Engine cannot be started (crank no start) Check Engine Light illuminated One or more of the following faults may be stored in the DME: 2A37 - Valvetronic, eccentric shaft sensor plausibility 2A47 - Valvetronic, eccentric shaft, signal plausibility 134E08 - Eccentric shaft plausibility (on F10, F25 vehicles only) CAUSE The VVT eccentric shaft sensor connector, and/or DME connector may have oil contamination due to oil leakage at the VVT sensor gasket.
Associated Products (50)Associated Documents - March 1, 2016•Document ID: 10151170Service Bulletin/Repair InstructionsENGINE; FUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- B122110
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryN51 Engine: Service Engine Soon Lamp Illuminated - Loss of Power and Various Faults Stored in the DME. The customer complains that the Service Engine Soon lamp is illuminated. The vehicle has lost power; the engine cranks but will not start; and various faults are stored in the DME for engine misfire and/or mixture adaptations. CAUSE The vehicle has lost fuel system delivery pressure due to a loose or split fuel line inside the fuel tank. The failure is related to an unfavorable stacking of tolerances between the rubber fuel hose and the plastic regulator nipple or deterioration of the rubber hose construction material.
Associated Products (44)Associated Documents - February 1, 2016•Document ID: 10151079Service Bulletin/Repair InstructionsEQUIPMENT; FUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- B130315
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummarySI B13 03 15 February 2016 Fuel Systems Technical Service This Service Information bulletin supersedes SI B13 03 15 dated March 2015 and replaces SI B13 04 13 dated March 2014. SUBJECT N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
Associated Products (213)Associated Documents - February 1, 2016•Document ID: 10151068Service Bulletin/Repair InstructionsSTEERING; ELECTRICAL SYSTEM; EQUIPMENT; ENGINE
- Mfr Comm. #:
- B070314
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryThis Service Information bulletin supersedes SI B07 03 14 dated October 2015. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Associated Products (206)Associated Documents - January 1, 2016•Document ID: 10151028Service Bulletin/Repair InstructionsAIR BAGS; EQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- B656906
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary"This Service Information bulletin supersedes SI B65 69 06 dated June 2008. designates changes to this revision SUBJECT Airbag Warning Lamp Illuminated, FC 93EB or FC 55 . The red airbag warning lamp (AWL) in the instrument cluster is illuminated and a fault code for ""Emergency call function..."" is stored in the MRS5 (Multiple Restraint System) control module. The fault code is FC 93EB for the E90 and E91 or FC 55 for the X3. The fault occurs regardless of whether the vehicle has a TCU (Telematics Control Unit) or not. Internal varistor fault within the MRS control module."
Associated Products (11)Associated Documents - January 1, 2016•Document ID: 10151023Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- B650709
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryWhistling Noise Coming from the Center Vent - A/C is Off . A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
Associated Products (289)Associated Documents - December 1, 2015•Document ID: 10147858Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- B090615
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryNew programming feature: Exclusion of Infotainment Control Units from Programming. Programming with ISTA/P 3.57.4, or a more recent update, displays a new Pop-Up window providing options for systems programming.
Associated Products (63)Associated Documents - November 1, 2015•Document ID: 10147837Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM
- Mfr Comm. #:
- B652606
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"The Disclaimer screen automatically disappears from the CID after 10 seconds. INFORMATION https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/28...12/2/2015 Page 2 of 2 An enhancement was made to the Car Communication Computer (CCC) and MASK (Multi Audio System Controller) in 2006 so the customer does not have to manually accept the ""Disclaimer"" screen each time. Older vehicles prior to the production dates listed above that are programmed with ISTA/P 2.52 or higher will also get this enhancement. WARRANTY INFORMATION Not applicable."
Associated Products (82)Associated Documents - October 1, 2015•Document ID: 10147758Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- B070314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryThis Service Information bulletin supersedes SI B07 03 14 dated May 2015. designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Associated Products (142)Associated Documents - September 1, 2015•Document ID: 10147242Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC; SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC
- Mfr Comm. #:
- B340414
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryDiagnosis of Compound Brake System Complaints in M Vehicles This Service Information bulletin supersedes SI 34 04 14 dated December 2014. Designates changes to the bulletin. INFORMATION 1.Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons.When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3.After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance.
Associated Products (100)Associated Documents - September 1, 2015•Document ID: 10147241Service Bulletin/Repair InstructionsWHEELS; POWER TRAIN:DRIVELINE
- Mfr Comm. #:
- B270415
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryShudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
Associated Products (176)Associated Documents - July 1, 2015•Document ID: 10147209Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- B640315
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryAir Conditioning Cooling is Insufficient or Inoperative. The air conditioner system refrigerant level is low or empty. CAUSE The evaporator is leaking refrigerant.
Associated Products (40)Associated Documents - June 1, 2015•Document ID: 10147724Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- B650215
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryiDrive Controller Trim Peeling. The chrome ring on the iDrive controller is peeling. Poor chrome material adhesion.
Associated Products (77)Associated Documents - May 1, 2015•Document ID: 10147136Service Bulletin/Repair InstructionsTIRES:VALVE; WHEELS
- Mfr Comm. #:
- B360215
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryValve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015
Associated Products (219)Associated Documents - May 1, 2015•Document ID: 10147123Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B070314
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryDiagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Associated Products (142)Associated Documents - April 1, 2015•Document ID: 10152314Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B620315
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
SummaryDoor Open Message Displayed, Even Though Door Is Closed. The customer complains that while driving, a CCM (check control message) indicates the doors are open, even though they are closed. Also, sometimes the gong will sound and the interior lights will go on and off. Unspecified FRM door lock status due to voltage variations
Associated Products (63)Associated Documents - February 1, 2015•Document ID: 10147090Service Bulletin/Repair InstructionsEQUIPMENT; STRUCTURE
- Mfr Comm. #:
- 650215
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummarySiDrive Controller Trim Peeling. The chrome ring on the iDrive controller is peeling. Poor chrome material adhesion
Associated Products (63)Associated Documents - February 1, 2015•Document ID: 10147067Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 070314
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryThis Service Information bulletin supersedes SI B07 03 14 dated February 2015. designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Associated Products (142)Associated Documents