Jeep Wrangler Complaints

18,838 consumer complaints on file.

#11756826August 13, 2026
FUEL/PROPULSION SYSTEM, ENGINE, UNKNOWN OR OTHER
"My vehicle [XXX] is subject to open Safety Recall for a high-voltage battery fire risk. The manufacturer has issued a 'Do Not Drive' / 'Park Outside' advisory, deeming the vehicle unsafe for operation. The Safety Defect: The vehicle poses an immediate fire hazard while charging or driving due to battery failure. Manufacturer Failure: Despite acknowledging the safety defect, Stellantis (Jeep) and the authorized dealer (Jerry V's Windward Hawaii Kaneohe Jeep) have refused to provide a loaner vehicle or direct-bill rental coverage. They insist on out-of-pocket reimbursement only, which I cannot afford. Impact: I am left without safe transportation for a known life-safety defect. The manufacturer is failing to remedy the safety issue within a reasonable time as required by federal law, leaving me stranded and at risk. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11756483August 12, 2026
ELECTRICAL SYSTEM
The 3.5-inch Instrument Panel Cluster went completely black while operating the vehicle, causing a total loss of speedometer and critical safety indicators (violating FMVSS 101). Concurrently, the engine computer limited vehicle performance to 3,000 RPM (limp mode). The vehicle exhibits the exact failure mode detailed in NHTSA Campaign 24V-652 (Jeep Recall 30B), but the manufacturer has not yet added this VIN to the recall population.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11756488August 12, 2026
SERVICE BRAKES
ABS pump and module combination is making brake calipers to not released. It’s been two times in 6 months my brakes are used up and calipers locked. Jeep knows this issue across its brand of vehicles but not called for a recall. Parts are also in back order that says lot of vehicles has issues. Confirmed with local dealership.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11756568August 12, 2026
ELECTRICAL SYSTEM
The contact owns a 2018 Jeep Wrangler. The contact stated that while the vehicle was parked with her son inside the vehicle, the instrument panel went blank. No warning light was illuminated. A dealer was contacted. The vehicle was taken to a dealer where it was diagnosed and determined that the instrument cluster needed to be replaced. The vehicle was not repaired. The failure had occurred several times. The contact associated the failure with NHTSA Campaign Number: 24V652000 (ELECTRICAL SYSTEM); however, the VIN was not included in the recall. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline to report the failure. The approximate failure mileage was 106,000.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11756438August 12, 2026
FUEL/PROPULSION SYSTEM
When in electric mode - and this happens at all different battery percentages - it will drive normally for a bit and I've watched the screen and seen the KW go up and down normally for electric and it seems perhaps once the battery has heated up (my assumption) it throttles electric power at 46 or 48KW, and then does not accelerate anymore and instead will lose power/speed (which is dangerous in traffic) and eventually switch over to Hybrid and a message about Electric mode temporarily unavailable. While waiting for hybrid to kick on my speed decreases by about 15mph. This has also happened when trying to take off from a complete stop. So you can only accelerate and very slowly to perhaps 20-25mph then no more speed , nothing then hybrid clicks on and electric mode temporarily unavailable. It is basically making electric mode useless and dangerous. It occurs almost every time I drive it now, originally it was sporadic and has started to be more.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11756228August 11, 2026
SERVICE BRAKES
I am contacting you to report a serious safety and parts availability issue involving my 2015 Jeep Rubicon. Jeep is no longer making the ABS module for my vehicle available and I have been unable to obtain a replacement module anywhere else. This has been an ongoing issue for several years now. The ABS system is an important safety component, and without a functioning ABS module, the vehicle can not be driven safely. What is particularly concerning is that Jeep has effectively left owners with no reasonable way to repair this critical safety system. This is not a consmetic or convenience related part. The ABS system directly affects the vehicle's ability to brake safely, particularly during emergency braking or when traction is compromised. I would like NHTSA to investigate whether Jeep's failure to make replacement ABS modules available for these vehicles creates an unreasonable safety risk for owners. I also believe NHTSA should determine whether Jeep should be required to provide a remedy, replacement parts or other means of restoring the ABS system to safe operating conditions. Please let me know what additional information is needed to formally document this saftety complaint. Concerned for my safety and the safety of my family, [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11756283August 11, 2026
ELECTRICAL SYSTEM, POWER TRAIN, ENGINE
While driving on the highway, the check engine light illuminated. Approximately 5 to 10 minutes later, the battery warning light came on. Upon exiting the highway and coming to a stop at an intersection, the automatic engine Start/Stop system engaged and shut down the engine. When attempting to safely proceed, the vehicle suffered a complete electrical failure due to the 48V mild-hybrid eTorque system failing to restart the engine. The vehicle refused to crank, would not shift, and became entirely disabled and stranded in the middle of a live intersection, creating an extreme safety and collision hazard. The vehicle was towed to an authorized dealership, where technicians officially confirmed the failure. The dealer diagnosed the root cause as an internal electrical failure of the Motor Generator Unit (MGU / Belt-Driven Hybrid Starter Generator Assembly), which completely disabled the vehicle's charging and hybrid restart capabilities. The failed component is available for inspection.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11756358August 11, 2026
ELECTRICAL SYSTEM
The dashboard is completely out. I cannot see my speed,know if my lights are working, cannot not know if there is an issue with the car, cannot see gas. Completely unsafe. Year, make, and model are under the recall # 30B but because my vin is not bringing it up it is not covered despite matching everything else and it is a safety issue.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11755934August 10, 2026
ELECTRICAL SYSTEM
When driving or upon start up the instrument panel cluster goes black not being able to see speedometer or gas gauge.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11755958August 10, 2026
SERVICE BRAKES, HYDRAULIC
The contact owns a 2016 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, the vehicle experienced an ABS module failure. The ABS and traction control warning lights were illuminated. The dealer was contacted and diagnosed the vehicle with ABS control module failure; however, the part to repair the vehicle was not available. The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time to provide the parts for the repair. The manufacturer was made aware of the failure but was unable to determine when parts for the repair would be available. The failure mileage was approximately 80,000.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11756089August 10, 2026
SERVICE BRAKES
Have had this issue since I believe 2020 or 2021. Either way a long time. This issue concerns the ABS control module failure. The warning lights (Brake, ABS and traction control) are lit showing unavailable / issue. The computer is throwing code C2200. The parts to repair are not available. Online forums show this is a big issue within the Jeep Wrangler community. It has been reported that Internally, Jeep has acknowledged the issue by placing new inventory on an "engineering review" hold after admitting that a massive batch of newly manufactured replacement parts had fatal software flaws.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11755832August 10, 2026
STEERING
The steering column mechanically disconnected, causing a complete loss of steering control while traveling approximately 70 mph on a highway. I was in the right lane when steering control was lost without any warning signs, including noises, vibrations, warning lights, or increased steering resistance. I immediately activated the hazard lights, informed my passenger, checked surrounding traffic, and applied the brakes. The vehicle pulled to the left under braking, crossed into the left lane, and entered the grassy median. The vehicle continued through a steep V-shaped median and came to a stop before entering opposing traffic. A collision was narrowly avoided.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11756070August 10, 2026
STEERING
Our Jeep has a death wobble that has almost caused me to have three wrecks where it is taking me out of my lane of travel and put me in Lanes where other people are had to get to the side of the road and try to get it to stop wobbling it. Every time I hit a pothole or a bump it throws me into a death wobble. I'm worried that this might cause me to get into an accident or cause me to die this happens every time I drive it. I cannot go above 40 mph without causing a death wobble so now I have no use of my Jeep. It just sits
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11755952August 10, 2026
BACK OVER PREVENTION
The contact owns a 2024 Jeep Wrangler. The contact stated that while reversing, the rear-view camera intermittently displayed a distorted image. The dealer was contacted and advised the contact to take the vehicle for a diagnostic test. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 51,000.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11755697August 9, 2026
ENGINE, POWER TRAIN
VEHICLE & INCIDENT: 2019 Jeep Wrangler JL 2.0L Turbo. While climbing an extended grade on Hwy 87, vehicle experienced a sudden sluggish throttle anomaly and rapid coolant temperature spike from ~215F to 255F under load. Vehicle was pulled off and shut down within ~20 seconds. SUSPECTED FAILURE MODE & UNDERHOOD FIRE: Upon opening the hood, pressurized coolant had sprayed across the engine bay from a split in the smaller rubber hose branch of the engine coolant outlet assembly (Mopar PN 68280797AC). The hose split longitudinally ~13mm with the center ~32mm from the hose end. The vehicle is equipped with a Baja Designs T-Fitting to replace 68280784A The hot, pressurized coolant sprayed directly onto the exposed, center section of the turbocharger between the compressor and turbine sections and on the turbine section itself. The coolant is suspected to have flash-ignited on contact with the turbo, creating an active under hood fire that began spreading to the hood insulation liner. The fire was successfully doused roadside with water, preventing a total vehicle burn-down. No other fuel sources were noted and the lines to the turbocharger were intact and did not show evidence of a leak. SAFETY CONCERN / HAZARD FOR NHTSA: 1. FIRE HAZARD: Pressurized factory coolant hoses and plastic junctions on the 2.0T GMET4 are routed in close proximity to the unshielded turbine housing. A hose rupture under normal grade-climbing thermal loads results in high-pressure atomized coolant hitting an ignition source well above its auto-ignition point. 2. COMPONENT DEGRADATION: Rubber lines near the engine outlet appear susceptible to heat-fatigue failure under high ambient/high load conditions, posing a sudden fire hazard at highway speeds. REPAIR: Roadside trim/re-clamp of the split hose allowed temporary transit. Replacing full hose assembly (68280797AC), upgrading radiator lines, and performing a full OAT coolant flush/vacuum refill. No oil contamination was noted after the incident.
Crash:
No
Fire:
Yes
Injuries:
0
Deaths:
0
#11755722August 9, 2026
ELECTRICAL SYSTEM, ENGINE, POWER TRAIN
Purchased vehicle in question on 9/11/25 as a lease through the local Jeep dealership near my residence. Sometime around 4/26 to 5/26 my vehicle started to display odd operational patterns which were brought to my local dealerships attention. The first event where I was able to record any type of documentation was around 5/25/26. While driving, the vehicle would suddenly go into "limp mode" and rapidly decrease speed. Several check engine lights would appear to include: Service Electronic Throttle Control, Service Electronic Stability Control, Traction Control and the standard CEL. When this does happen, the vehicle will decrease speed suddenly without warning and becomes difficult to operate until it is pulled over and parked. Vehicle has been to my local dealership several times (4) and out of service for over 70 days with the latest stay 30+ days. According to documentation from the dealership, the listed error/issue has been recreated on their end at least one time but no data was captured with that fail. My local Jeep dealership Service Manager (CF) replied to an email of mine (7/16/26 at 1703) with the following statement: Verified customer concern of check engine light on connect to wytec and found p2173 stored in powertrain control module. Also found c121c stored in ABS module. Believe ABS code is related to PCM code, cleared codes test drove multiple times. Finally able to get customer concern to duplicate but no data was captured on this failure. We are continuing to drive the vehicle while monitoring data to catch freeze frame data while concern occurs but have not been able to do so far at this time. The condition, when it occurs presents a serious safety concern for the driver and other drivers as it will cause a sever throttle limitation and can cause the vehicle to slow down rapidly. As of 8/9/26, no fix confirmed for my vehicle and the dealership and manufacture are pushing to return my vehicle with confirmed fix. Jeep case number 97378351
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11755717August 9, 2026
ELECTRICAL SYSTEM, UNKNOWN OR OTHER
I purchased my vehicle in March 2026 from the.dealership with a known active recall from November 2025 with fire risk, now there is an additional fire hazard recall and my vehicle is currently undriveable due to these recalls.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11755687August 8, 2026
SERVICE BRAKES
The vehicle experienced repeated braking system failures that caused the front brakes to lock up while driving, overheat, and begin smoking. The front brake calipers, rotors, and pads were replaced multiple times,not lasting more than 3weeks before failing again. the problem continued to occur. The brake booster brake line and brake fluid were also replaced while attempting to diagnose the problem. Warning lights/messages appeared, including the ABS/traction control warning and “Service Electronic Stability Control.” The vehicle would also randomly turn off at stop lights and refuse to turn back on. An independent mechanic ultimately diagnosed a failure of the ABS control module. Showing a code “c2200” The vehicle is currently at the repair facility and is available for inspection. This failure created a serious safety risk because the brakes could engage/lock unexpectedly while the vehicle was being driven and the braking system became severely overheated and damaged multiple times. The vehicle is currently considered unsafe to drive unless I redo the whole braking system again and unplug the ABS module. I was informed that the required replacement ABS module is on national backorder with no reliable availability date and reliable refurbishes are also unable to do the repairs now. . I was also informed that obtaining a new replacement module may take an extended period of time. Because this is a safety-critical braking component, I am concerned that other vehicles with the same failure could experience unexpected brake malfunction or loss of safe braking control
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11755688August 8, 2026
AIR BAGS
Faulty Clockspring Diagnosed by independent dealer. The occupant restraint system came on my dash about a 2 weeks ago without any warning. The clockspring controls the airbags and puts me and my family at risk for injury.The code reads: Driver Airbag Squib 2 circuit open
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11755446August 7, 2026
ELECTRICAL SYSTEM
I have a 2018 Jeep Wrangler JL. Both digital and analog dash gauges have stopped working. I am unable to read odometer, speedometer, gas level, RPM, temperature gauge, etc. This poses a significant risk to my safety while driving.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0

← Back to Jeep Wrangler