MINI · Model Report
Showing safety data for the 2014 model year only.
BMW of North America, LLC (BMW) is recalling certain 2008-2014 MINI Clubman Cooper, Clubman Cooper S, Clubman John Cooper Works, and 2007-2013 MINI Hardtop 2-Door Cooper, Cooper S, and John Cooper Works vehicles sold, or ever registered, in Alaska, Colorado, Connecticut, Delaware, Illinois, Indiana, Iowa, Kansas, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, Nebraska, New Hampshire, New Jersey, New York, North Dakota, Ohio, Pennsylvania, Rhode Island, South Dakota, Utah, Vermont, Virginia, West Virginia, Washington D.C., and Wisconsin. The electronic control module in the driver's side footwell area may short-circuit, due to corrosion from water and road salt.
BMW of North America, LLC (BMW) is recalling certain model year 2014-2015 MINI Cooper Hardtop 2 door vehicles manufactured February 25, 2014, to May 16, 2015, 2014-2015 MINI Cooper S Hardtop 2 door vehicles manufactured March 28, 2014, to May 9, 2015, 2015 MINI Cooper Hardtop 4 door vehicles manufactured October 17, 2014, to June 2, 2015, and 2015 MINI Cooper S Hardtop 4 door vehicles manufactured November 24, 2014, to June 11, 2015. During a service appointment, the affected vehicles received replacement front passenger seat cushions (which contain integral Capacitive Interior Sensing (CIS) functions). The CIS functions may have been incorrectly calibrated, and if so, would cause impaired occupant classification and thus inappropriate air bag activation/deactivation.
BMW of North America, LLC (BMW) is recalling certain model year 2014-2016 MINI Cooper S and MINI Cooper two-door vehicles, 2015-2016 MINI John Cooper Works and MINI Cooper S and MINI Cooper four-door vehicles and 2014-2015 BMW i3 vehicles. Due to a manufacturing error, the passenger frontal air bag may not deploy properly in a low speed crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 208, "Occupant Crash Protection."
BMW of North America, LLC (BMW) is recalling certain model year 2014-2015 MINI Cooper and MINI Cooper S Hardtop 2 Door vehicles and 2015 MINI John Cooper Works Hardtop 2 Door vehicles. The affected vehicles do not meet the side impact performance requirements for the rear seat passengers. As such, these vehicles fail to comply with Federal Motor Vehicle Safety Standard (FMVSS) number 214, "Side Impact Protection."
BMW of North America, LLC (BMW) is recalling certain model year 2014-2015 MINI Cooper Hardtop two door vehicles manufactured December 1, 2013, to December 14, 2014. The affected vehicles may have been manufactured with an incorrect maximum capacity weight stated on the Tire Information Placard. Thus, these vehicles fail to comply with Federal Motor Vehicle Safety Standard (FMVSS) No. 110, "Tire Selection and Rims and Motor Home/Recreation Vehicle Trailer Load Carrying Capacity Information for Motor Vehicles with a GVWR of 4,536 kilograms (10,000 pounds) or less."
The "Passenger Airbag Off" light is illuminated, meaning the primary safety restraint system is disabled. The failed component is the "Occupancy Classification System (OCS) / OC3 Sensor Mat." I purchased a very well-maintained 2014 MINI in March 2026 and the failure occurred shortly after the 10-year warranty window expired. BMW Group has similar BMW models using the very same technology, and they received 15-year extensions, not 10. BMW Coverage: Has extended the warranty for the OC3 mat to 15 years/Unlimited miles for specific "eligible US-specification" models like the 3 Series, 5 Series, and Z4. MINI Coverage: Currently caps the warranty extension at 10 years/120,000 miles for its eligible vehicles.
No injuries · No fire · No crash
The contact owns a 2014 Mini Cooper. The contact stated that the front driver's side and passenger’s side doors and windows failed to properly close. The vehicle was taken to the local mechanic who diagnosed the vehicle and determined that the failure was caused by a faulty foot well module which caused the electrical power windows to malfunction and the doors to not properly close. The vehicle was not yet repaired. The manufacturer and local dealer were notified of the failure, but no assistance was offered. The contact was informed that the VIN was not included in NHTSA Campaign Number: 23V337000 (ELECTRICAL SYSTEM). The contact stated that the vehicle had experienced the failure listed in the recall. The failure mileage was 80,000.
No injuries · No fire · No crash
Engine motor mount sheared, allowing motor to interact with and bounce directly on the frame, and stressing the other connections and components. Dealer indicated this is a very common problem for this car model and is likely a design issue, and even had another example of a sheared mount on display in order to show others with the same issue.
No injuries · No fire · No crash
The contact owns a 2014 Mini Cooper Clubman. The contact received notification of NHTSA Campaign Number: 23V337000 (Electrical System) however, the part to do the recall repair was not yet available. The local dealer was contacted, and the contact was informed that the part for the recall repair was not yet available. The contact stated that the manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
No injuries · No fire · No crash
The fuse box JBE module has a Quality Assurance problem with a solder connection to the NEC low pressure fuel relay. This is a known issue with BMW/Mini. The car suddenly stalls without warning. If the driver is not keen or if traffic patterns do not allow, the car can be left in very dangerous situations on the highway or in the middle of intersection. The repair for this problem is widely distributed online via blogs and YouTube, but replacement modules are $1500 (part only) and these modules are not available until at least October 2023. There are no warning lights or other warnings prior to the incident. While I am not aware of any serious injuries, it is only a matter of time before someone is t-boned at an intersections. This part MUST be immediately recalled due to the safety risk. The images below show the JBE fuse box housing as well as the PCB where the cold solder joint can be seen. I have circled the cold solder joint in the close up picture.
No injuries · No fire · No crash