Nissan Altima Service Bulletins
1,075 manufacturer communications on file.
- October 21, 2016•Document ID: 10109141Service Bulletin/Repair InstructionsSTRUCTURE:BODY
- Mfr Comm. #:
- Update - PC497 -
- Date Added:
- August 1, 2017
- Manufacturer:
- NISSAN
SummaryFront Member Welds - Quality Assurance Hold ***** Detailed Information ***** On October 14th, 2016, Nissan announced a Quality Assurance (QA) Hold on certain MY2017 Nissan Altima and Maxima vehicles identified in Service Comm as a precaution. Further investigation by Nissan confirmed the subject vehicles meet Nissan's standards and applicable regulations and require no further action. Accordingly, the Quality Assurance Hold is rescinded. IMPORTANT: Effective immediately, the Quality Assurance Hold is rescinded and the subject vehicles may be released for sale. ***** What Dealers Should Do ***** 1. Effective immediately, dealers may release for sale any vehicles in dealer inventory affected by this quality hold.
Associated Products (2)Associated Documents - October 14, 2016•Document ID: 10109137Service Bulletin/Repair InstructionsSTRUCTURE:BODY
- Mfr Comm. #:
- PC497 - 2017 Alt
- Date Added:
- August 1, 2017
- Manufacturer:
- NISSAN
SummaryFront Member Welds - Quality Assurance Hold ***** Detailed Information ***** Nissan is committed to a high level of customer service and satisfaction. This commitment requires Nissan to periodically place certain specific vehicles on a temporary Quality Assurance (QA) Hold to assure that these vehicles, as delivered to our customers, meet our exacting standards and our customers? expectations. Effective immediately, Nissan is placing a temporary Quality Assurance (QA) Hold on approximately 408 specific MY2017 Altima (L33) and 152 specific MY2017 Maxima (A36) vehicles. ***** What Dealers Should Do ***** 1. Verify if vehicles currently in dealer inventory are affected by this QA Hold using Service Comm I.D. PC497 Note: Dealers should continue to check new arriving inventory for QA Hold applicability. 2. Please do not drive, sell, or trade the specific 2017 Altima and Maxima vehicles in Dealer Inventory subject to this QA Hold. 3. No further action is necessary at this time. Nissan will provide an update by October 28th, 2016.
Associated Products (2)Associated Documents - October 13, 2016•Document ID: 10120587Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- NTB13-079e
- Date Added:
- October 25, 2017
- Manufacturer:
- NISSAN
Summary2007-2010 ALTIMA; REDUCED PERFORMANCE DUE TO CVT FLUID TEMPERATURE PROTECTION LOGIC This bulletin has been amended to remove 2011 and 2012 model years. Please discard all previous versions of this bulletin.
Associated Products (4)Associated Documents - October 13, 2016•Document ID: 10109129Service Bulletin/Repair InstructionsVEHICLE SPEED CONTROL; EQUIPMENT
- Mfr Comm. #:
- NTB16-098
- Date Added:
- August 1, 2017
- Manufacturer:
- NISSAN
Summary2011-2012 ALTIMA; REDUCED PERFORMANCE DUE TO CVT FLUID TEMPERATURE PROTECTION LOGIC IF YOU CONFIRM The vehicle speed is, or was, reduced by the CVT fail-safe (reduced vehicle speed) after continuous operation under the following conditions: - High RPM and/or high speed driving (RPM of 4000+ or speeds of 65 mph (104.6 km/h) for 1.0 - 1.5 hrs. or more) - Driving in ambient temperature of 96 degrees or higher - Climbing steep or extended hills for 6 miles (9.6 km) or more - Whine or rattle type noise occurring during reduced engine performance (vehicle speed decrease) ACTION 1. Perform a self-diagnosis with CONSULT-III plus (C-III plus). - If DTCs are present other than P0744, refer to the appropriate section of the Electronic Service Manual (ESM) and diagnose the DTCs first before proceeding to step 2 of ACTION. 2. Check the number of counts of "CVT-A? with C-III plus. - Refer to the Flow Chart on page 2 and the Service Procedure starting on page 3 to confirm if this bulletin applies.
Associated Products (2)Associated Documents - October 10, 2016•Document ID: 10120589Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- NTB15-049i
- Date Added:
- October 25, 2017
- Manufacturer:
- NISSAN
SummaryTELEMATICS SERVICE INFORMATION ONLY SPECIFIC TRIM PACKAGES ARE AFFECTED This bulletin has been amended. Information for 2017 Altima, Murano, Pathfinder, Sentra, and Titan/Titan XD vehicles has been applied. No other changes have been made. Please discard previous versions of this bulletin.
Associated Products (12)Associated Documents - October 5, 2016•Document ID: 10109136Service Bulletin/Repair InstructionsVEHICLE SPEED CONTROL:ACCELERATOR PEDAL
- Mfr Comm. #:
- PC495 2016-17 Al
- Date Added:
- August 1, 2017
- Manufacturer:
- NISSAN
SummaryCAMPAIGN BULLETIN - Accelerator Pedal ***** Detailed Information ***** Nissan is conducting a dealer inventory inspection on approximately 5,797 MY2016-17 Nissan Altima and 1,646 MY2017 Maxima vehicles to tighten the accelerator pedal mounting bolts to specification. ***** What Dealers Should Do ***** 1. Verify if vehicles currently in dealer inventory are affected by this inventory inspection using Service Comm I.D. PC495. 2. Use the attached repair procedure to tighten the accelerator pedal mounting bolts to specification. - If bolts are missing, please send the requested information to [email protected] and await further instruction. 3. Submit the warranty claim, and release the vehicle. Note: Dealers should continue to check new arriving inventory for applicability. 4. Dealers are requested to inspect any affected vehicle in dealer new or pre-owned inventory to ensure customer satisfaction.
Associated Products (3)Associated Documents - September 28, 2016•Document ID: 10091576Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- NTB12-070B
- Date Added:
- February 14, 2017
- Manufacturer:
- NISSAN
Summary"NO AUDIO DURING PHONE CALL WITH APPLE IOS 10, NAVIGATION SYSTEM REBOOTS, AND/OR AUDIO CONTROLS WILL NOT RESPOND THIS BULLETIN HAS BEEN AMENDED. THE TITLE AND IF YOU CONFIRM SECTION HAVE BEEN REVISED. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN."
Associated Products (20)2014 Nissan GT-R2013 Nissan 370Z2013 Nissan Altima2013 Nissan Armada2013 Nissan GT-R2013 Nissan Murano2013 Nissan Pathfinder2012 Nissan 370Z2012 Nissan Altima2012 Nissan Maxima2012 Nissan Murano2011 Nissan 370Z2011 Nissan Altima2011 Nissan GT-R2011 Nissan Maxima2011 Nissan Murano2010 Nissan 370Z2010 Nissan Altima2010 Nissan GT-R2010 Nissan MaximaAssociated Documents - September 27, 2016•Document ID: 10091608Service Bulletin/Repair InstructionsLATCHES/LOCKS/LINKAGES:DOORS:LATCH
- Mfr Comm. #:
- NTB16-092
- Date Added:
- February 14, 2017
- Manufacturer:
- NISSAN
Summary"NISSAN; DOORS DIFFICULT TO CLOSE WITH TEMPERATURE BELOW FREEZING IF YOU CONFIRM: THE FOLLOWING INCIDENT, OR THE CUSTOMER REPORTS THIS INCIDENT: - THE VEHICLE HAS BEEN SETTING (NOT RUNNING) IN TEMPERATURES BELOW 14°F (-10°C) FOR AN EXTENDED PERIOD (SUCH AS OVERNIGHT). THEN - A SIDE DOOR IS OPENED. THEN - THE DOOR IS DIFFICULT TO CLOSE/LATCH, WILL NOT CLOSE/LATCH WITH NORMAL PRESSURE; REQUIRES ADDITIONAL EFFORT TO CLOSE/LATCH, OR THE DOOR MAY ONLY LATCH HALF WAY. THEN - THE DOOR WILL CLOSE/LATCH NORMALLY WHEN THE VEHICLE HAS WARMED UP (VEHICLE LEFT IN THE SUN, MOVED INDOORS, OR DRIVEN FOR SEVERAL MINUTES). NOTE: O THE ABOVE INCIDENT DOES NOT APPLY TO SLIDING SIDE DOORS OR A REAR HATCH (BACK DOOR). O THE ABOVE INCIDENT, IF IT SHOULD OCCUR, COULD BE CONFIRMED OR REPORTED FOR ONE OR MORE SIDE DOORS. ACTION REPLACE THE DOOR LOCK FOR THE AFFECTED DOOR. - DO NOT REPLACE ALL SIDE DOOR LOCKS AUTOMATICALLY. REPLACE ONLY THE DOOR LOCK OF THE DOOR(S) WITH THE INCIDENT AS DESCRIBED UNDER IF YOU CONFIRM. - REFER TO THE ELECTRONIC SERVICE MANUAL (ESM), SECTION DLK DOOR & LOCK FOR REPLACEMENT PROCEDURE."
Associated Products (25)2016 Nissan Altima2016 Nissan Leaf2016 Nissan NV2002016 Nissan Pathfinder2016 Nissan Rogue2016 Nissan Sentra2016 Nissan Versa Note2015 Nissan Altima2015 Nissan Leaf2015 Nissan NV2002015 Nissan Pathfinder2015 Nissan Rogue2015 Nissan Sentra2015 Nissan Versa Note2014 Nissan Altima2014 Nissan Leaf2014 Nissan NV2002014 Nissan Pathfinder2014 Nissan Rogue2014 Nissan Sentra+ 5 moreAssociated Documents - September 9, 2016•Document ID: 10091575Service Bulletin/Repair InstructionsPOWER TRAIN:AUTOMATIC TRANSMISSION
- Mfr Comm. #:
- NTB12-057C
- Date Added:
- February 14, 2017
- Manufacturer:
- NISSAN
Summary"ALTIMA, SENTRA, AND ROGUE; CVT FAIL-SAFE CONDITION SERVICE INFORMATION THIS BULLETIN HAS BEEN AMENDED. THE APPLIED VEHICLES SECTION HAS BEEN REVISED. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN."
Associated Products (20)2015 Nissan Rogue2014 Nissan Rogue2013 Nissan Rogue2012 Nissan Altima2012 Nissan Rogue2012 Nissan Sentra2011 Nissan Altima2011 Nissan Rogue2011 Nissan Sentra2010 Nissan Altima2010 Nissan Rogue2010 Nissan Sentra2009 Nissan Altima2009 Nissan Rogue2009 Nissan Sentra2008 Nissan Altima2008 Nissan Rogue2008 Nissan Sentra2007 Nissan Altima2007 Nissan SentraAssociated Documents - September 6, 2016•Document ID: 10091586Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
- Mfr Comm. #:
- NTB15-099B
- Date Added:
- February 14, 2017
- Manufacturer:
- NISSAN
Summary"SERVICE INFORMATION FOR DTCS C1A12 AND C1A16 THIS BULLETIN HAS BEEN AMENDED. THE APPLIED VEHICLES SECTION HAS BEEN REVISED, A PHOTO HAS BEEN ADDED TO PAGE 4, AND ICC/DISTANCE SENSOR LOCATION INFORMATION FOR MAXIMA AND ROGUE HAS BEEN ADJUSTED. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN."
Associated Products (7)Associated Documents - August 25, 2016•Document ID: 10091528Service Bulletin/Repair InstructionsPOWER TRAIN:AUTOMATIC TRANSMISSION
- Mfr Comm. #:
- NTB16-085
- Date Added:
- February 14, 2017
- Manufacturer:
- NISSAN
Summary"ENHANCED DIAGNOSTIC LOGIC FOR CVT PATHFINDER AND ALTIMA WITH V6 ENGINE ONLY IF YOU CONFIRM THE CUSTOMER REPORTS A TRANSMISSION JUDDER (SHAKE, SHUDDER, SINGLE OR MULTIPLE BUMPS OR VIBRATION). NOTE: A NEW DIAGNOSTIC LOGIC HAS BEEN ESTABLISHED TO ENHANCE THE DIAGNOSTIC PROCESS BY STORING DIAGNOSTIC TROUBLE CODES (DTCS) ON APPLIED VEHICLES. THE NEW DTCS ARE: P17F1 (CVT_JUDDER [C/U INSPECTION]) P17F0 (CVT_JUDDER [T/M INSPECTION]) ACTION 1. REFER TO PAGE 4, STEP 6 IN THE SERVICE PROCEDURE TO CONFIRM THIS BULLETIN APPLIES TO THE VEHICLE YOU ARE WORKING ON. 2. IF THIS BULLETIN APPLIES, REPROGRAM THE TCM (TRANSMISSION CONTROL MODULE)."
Associated Products (10)Associated Documents - August 25, 2016•Document ID: 10091527Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- NTB16-084
- Date Added:
- February 14, 2017
- Manufacturer:
- NISSAN
Summary"2013-2015 ALTIMA WITH 4-CYL ENGINE; CABIN BOOM AND/OR STEERING/FLOOR VIBRATION WHILE DRIVING 4-CYLINDER ENGINE ONLY IF YOU CONFIRM: A BOOM OR DRONE SENSATION IS HEARD IN THE CABIN AREA AND/OR A VIBRATION IS FELT IN THE FLOOR AND/OR STEERING WHEEL WHEN DRIVING AND THE ENGINE IS APPROXIMATELY 1,800 RPM. ACTION: 1. CHECK THE GAP BETWEEN THE RUBBER AND METAL PORTIONS OF THE FRONT TUBE EXHAUST HANGER (SEE FIGURE 1 AND PAGE 2, FIGURE 2). 2. IF LESS THAN 1 MM (0.04 INCH) GAP, ADD SHIMS (FLAT WASHERS) BETWEEN THE FRONT SUSPENSION MEMBER AND FRONT EXHAUST TUBE HANGER. SEE PAGE 2, FIGURE 2 AND 3. - MAXIMUM SHIM THICKNESS: 4.6 MM (0.18 INCH)"
Associated Products (3)Associated Documents - August 9, 2016•Document ID: 10091506Service Bulletin/Repair InstructionsPOWER TRAIN:AUTOMATIC TRANSMISSION
- Mfr Comm. #:
- NTB15-086D
- Date Added:
- February 14, 2017
- Manufacturer:
- NISSAN
Summary"2013-2016 ALTIMA AND 2014-2016 ROGUE; MIL ON WITH DTC P0776, P1715 MAY HAVE HESITATION AND/OR LACK OF POWER ALTIMA WITH 4-CYLINDER ENGINE ONLY THIS BULLETIN HAS BEEN AMENDED. THE TITLE IS CHANGED, A DTC IS ADDED UNDER IF YOU CONFIRM, AND TCM REPROGRAMMING IS ADDED TO THE SERVICE PROCEDURE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN."
Associated Products (8)Associated Documents - August 4, 2016•Document ID: 10091503Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
- Mfr Comm. #:
- NTB13-097D
- Date Added:
- February 14, 2017
- Manufacturer:
- NISSAN
Summary"ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION THIS BULLETIN HAS BEEN AMENDED. THE TITLE HAS BEEN REVISED, AND THE BULLETIN NOW INCLUDES VEHICLES IN PRODUCTION AS OF THE DATE OF THIS UPDATE. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD ALL PREVIOUS VERSIONS OF THIS BULLETIN."
Associated Products (104)2017 Nissan Altima2017 Nissan Armada2017 Nissan Leaf2017 Nissan Maxima2017 Nissan Murano2017 Nissan Pathfinder2017 Nissan Rogue2017 Nissan Titan2017 Nissan Versa2016 Nissan 370Z2016 Nissan Altima2016 Nissan Armada2016 Nissan Cube2016 Nissan Frontier2016 Nissan GT-R2016 Nissan Juke2016 Nissan Leaf2016 Nissan Maxima2016 Nissan Murano2016 Nissan NV+ 84 moreAssociated Documents - July 29, 2016•Document ID: 10091072Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- R1620 2016 MAXIM
- Date Added:
- February 9, 2017
- Manufacturer:
- NISSAN
Summary"REAR O2 SENSOR VOLUNTARY EMISSIONS RECALL CAMPAIGN ***** CAMPAIGN SUMMARY ***** NISSAN IS CONDUCTING A VOLUNTARY EMISSIONS RECALL CAMPAIGN TO UPDATE THE ELECTRONIC CONTROL MODULE (ECM) SOFTWARE ON CERTAIN MODEL YEAR 2016 NISSAN MAXIMA (A36), AND MODEL YEAR 2015-16 ALTIMA (L33), JUKE (F15), PATHFINDER (R52), MURANO (Z52) AND QUEST (E52) VEHICLES. UNDER CERTAIN CONDITIONS, THE REAR OXYGEN (O2) SENSOR SIGNAL COULD FAIL, RESULTING IN THE REAR OXYGEN (O2) SENSOR OBD MONITOR BEING DISABLED WITHOUT THE CUSTOMER BEING ALERTED. NISSAN PLANS TO BEGIN NOTIFYING OWNERS OF AFFECTED VEHICLES IN AUGUST, ASKING THEM TO BRING THEIR VEHICLES TO AN AUTHORIZED NISSAN DEALERSHIP. ***** WHAT DEALERS SHOULD DO**** 1. VERIFY IF VEHICLES ARE AFFECTED BY THIS VOLUNTARY EMISSION RECALL CAMPAIGN USING SERVICE COMM I.D. R1620. NOTE: NEW VEHICLES IN DEALER INVENTORY CAN BE ALSO BE IDENTIFIED USING DCS (SALES-> VEHICLE INVENTORY, AND FILTER BY OPEN CAMPAIGN). - REFER TO NPSB 15-460 FOR ADDITIONAL INFORMATION 2. THE SUBJECT VEHICLES ARE NOT ON SALES HOLD, BUT FOR CUSTOMER CONVENIENCE, DEALERS ARE ENCOURAGED TO PERFORM THIS CAMPAIGN ON ANY AFFECTED VEHICLES IN THEIR INVENTORY PRIOR TO SALE, LEASE, OR TRADE. 3. DEALERS SHOULD USE NTB16-073 TO CORRECT ANY VEHICLES SUBJECT TO THIS CAMPAIGN. 4. ONCE REPAIRED, DEALER SHOULD SUBMIT A WARRANTY CLAIM AND RELEASE THE VEHICLE."
Associated Products (12)Associated Documents - July 28, 2016•Document ID: 10091322Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- NTB16-073
- Date Added:
- February 13, 2017
- Manufacturer:
- NISSAN
Summary"VOLUNTARY EMISSIONS RECALL CAMPAIGN ECM REPROGRAMMING INTRODUCTION NISSAN IS CONDUCTING A VOLUNTARY EMISSION RECALL CAMPAIGN ON CERTAIN MODEL YEAR 2015-2016 ALTIMA, 2015-2016 JUKE, 2016 MAXIMA, 2015-2016 MURANO, 2015-2016 QUEST, AND 2015-2016 PATHFINDER VEHICLES. NISSAN HAS DISCOVERED THAT THESE VEHICLES ARE EQUIPPED WITH AN ON-BOARD DIAGNOSTICS (OBD) CALIBRATION THAT, IF NOT REPAIRED, MAY NOT DETECT A REAR OXYGEN (O2) SENSOR SHORT-TO-GROUND OR SHORT-TO-BATTERY CONDITION. THE ECM (ENGINE CONTROL MODULE) WILL BE REPROGRAMMED. THIS SERVICE WILL BE PERFORMED AT NO CHARGE FOR PARTS OR LABOR. IDENTIFICATION NUMBER NISSAN HAS ASSIGNED IDENTIFICATION NUMBER R1620 TO THIS CAMPAIGN. THIS NUMBER MUST APPEAR ON ALL COMMUNICATIONS AND DOCUMENTATION OF ANY NATURE DEALING WITH THIS CAMPAIGN. DEALER RESPONSIBILITY IT IS THE DEALERS RESPONSIBILITY TO CHECK SERVICE COMM FOR THE CAMPAIGN STATUS ON EACH VEHICLE FALLING WITHIN THE RANGE OF THIS VOLUNTARY EMISSIONS RECALL WHICH FOR ANY REASON ENTERS THE SERVICE DEPARTMENT. THIS INCLUDES VEHICLES PURCHASED FROM PRIVATE PARTIES OR PRESENTED BY TRANSIENT (TOURIST) OWNERS AND VEHICLES IN A DEALERS INVENTORY."
Associated Products (11)Associated Documents - July 27, 2016•Document ID: 10091413Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- NTB14-012D
- Date Added:
- February 13, 2017
- Manufacturer:
- NISSAN
Summary"REMOTE ENGINE START NOT WORKING THIS BULLETIN HAS BEEN AMENDED. CHANGES HAVE BEEN MADE TO ITEMS 1, 4, AND 13 IN THE SUPPLEMENTAL DIAGNOSIS TABLE. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN. SERVICE INFORMATION IF A CUSTOMER STATES THE REMOTE ENGINE START (RES) FEATURE OF AN APPLIED VEHICLE IS NOT WORKING, MAKE SURE THE SYSTEM IS PROPERLY SET TO OPERATE: -THE IGNITION IS TURNED OFF -THE SHIFT SELECTOR IS IN PARK (P) -THE HOOD/DOORS/TRUNK LID/LIFT GATE ARE COMPLETELY CLOSED -NO OTHER OF THE VEHICLES INTELLIGENT KEYS (I-KEYS) ARE INSIDE, OR WITHIN STARTING RANGE OF, THE VEHICLE -THE I-KEY/KEY FOB (KEY FOB) IS WITHIN THE OPERATING RANGE OF 197 FT OR 60 M IF THE ABOVE CONDITIONS ARE MET, RES SHOULD WORK. 1. POINT THE KEY FOB AT THE VEHICLE. 2. PRESS THE LOCK BUTTON. 3. PRESS AND HOLD THE RES BUTTON WITHIN FIVE (5) SECONDS OF PRESSING THE LOCK BUTTON, UNTIL THE TURN SIGNAL LIGHTS TURN ON. WHENEVER AN APPLIED VEHICLE HAS A CONCERN WITH THE REMOTE ENGINE START (RES) FEATURE NOT WORKING PROPERLY, MAKE SURE TO VERIFY THE INCIDENT BEFORE STARTING ANY DIAGNOSIS AND/OR REPLACING PARTS. FOR A BETTER UNDERSTANDING OF THE RES SYSTEM, REFER TO SECTION 3: PRE-DRIVING CHECKS AND ADJUSTMENTS > REMOTE ENGINE START OF THE APPLIED VEHICLES OWNERS MANUAL. WHEN DIAGNOSING RES OPERATION, USE THE SUPPLEMENTAL RES SERVICE INFORMATION AND SUPPLEMENTAL DIAGNOSIS TABLE (STARTING ON PAGE 2) IN ADDITION TO THE ESM."
Associated Products (12)Associated Documents - July 22, 2016•Document ID: 10091409Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:IGNITION
- Mfr Comm. #:
- NTB09-118D
- Date Added:
- February 13, 2017
- Manufacturer:
- NISSAN
Summary"INTELLIGENT KEY BATTERY VOLTAGE CHECK AND REPLACEMENT THIS BULLETIN HAS BEEN SUPERSEDED BY NTB15-077. NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN."
Associated Products (12)Associated Documents - July 12, 2016•Document ID: 10091417Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:12V/24V/48V BATTERY
- Mfr Comm. #:
- NTB15-077A
- Date Added:
- February 13, 2017
- Manufacturer:
- NISSAN
Summary"NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK THIS BULLETIN HAS BEEN AMENDED. CHANGES HAVE BEEN MADE THROUGHOUT. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN. IF YOU CONFIRM THE INTELLIGENT KEY INTERMITTENTLY OR CONTINUOUSLY DOES NOT FUNCTION. ACTION CHECK THE BATTERY CONDITION WITH THE SIGNAL TECH-II I-KEY BATTERY TEST. IMPORTANT: CONFIRM THAT THE SIGNAL TECH-II HAS THE MOST RECENT UPDATE. UPDATE CAN BE PERFORMED THROUGH ASIST / SPECIALTY TOOLS / SIGNAL TECH-II."
Associated Products (12)Associated Documents - June 24, 2016•Document ID: 10192845Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; LATCHES/LOCKS/LINKAGES
- Mfr Comm. #:
- NTB16028A
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummarySERVICE INFORMATION If it appears, for any or all of the Intelligent Keys on an applied vehicle, that all "RKE" lock/unlock/panic/trunk button functions of that specific Intelligent Key(s) does not work BUT The doors will lock and unlock when pressing either front door request switch while using the particular Intelligent Key(s) (see Figure 1 below), THEN That specific Intelligent Key may have become de-synchronized with the vehicle. NOTE: - Intelligent Key de-synchronization may occur if the Intelligent Key is not used for extended periods of time or if the Intelligent Key was not operating due to low battery condition and the battery has been replaced. - Do NOT replace the BCM, Intelligent Key, or any other parts if an Intelligent Key only needs to be re-synchronized. See this bulletin for further detail.
Associated Products (3)Associated Documents