Nissan Altima Service Bulletins
1,075 manufacturer communications on file.
- January 23, 2017•Document ID: 10109153Service Bulletin/Repair InstructionsPOWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- NTB16-121a
- Date Added:
- August 1, 2017
- Manufacturer:
- NISSAN
SummaryVOLUNTARY SERVICE CAMPAIGN 2013-2016 ALTIMA AND 2014-2016 ROGUE; TCM REPROGRAMMING This bulletin has been amended. A link for using the BOSCH MTS 6513 to perform the reprogramming has been added. No other changes have been made. Please discard previous versions of this bulletin.
Associated Products (7)Associated Documents - January 20, 2017•Document ID: 10109163Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL; ENGINE
- Mfr Comm. #:
- PC514 - 2016-17
- Date Added:
- August 1, 2017
- Manufacturer:
- NISSAN
SummaryECM Reprogram Voluntary Emissions Service Campaign This bulletin applies only to vehciles equipped with 4 cylinder engine. ***** Campaign Summary***** Nissan is conducting a Voluntary Emissions Service Campaign on approximately 311,675 specific 2016-2017 model year Nissan Altima vehicles equipped with a 2.5L engine. Nissan has discovered that some model year 2016 and 2017 Altima vehicles are equipped with an improperly calibrated Engine Control Module (ECM) that may illuminate a Malfunction Indicator Light (MIL) for abnormal Air/Fuel (A/F) sensor output. The cause is a grille shutter calibration issue which may lead to higher than expected A/F sensor temperature, resulting in the MIL for delayed sensor response rate. To correct this condition, Nissan is conducting a Voluntary Emissions Service Campaign to reprogram the Engine Control Module (grille shutter opening logic) free of charge. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm I.D. PC514. 2. Dealers are requested to repair any affected vehicles in dealer new or pre-owned inventory to ensure customer satisfaction. 3. Dealers should use NTB16-514 to correct any vehicles subject to this campaign. 4. Once repaired, dealers should submit the claim, using the claims coding provided, and release the vehicle.
Associated Products (2)Associated Documents - January 19, 2017•Document ID: 10109155Service Bulletin/Repair InstructionsPOWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- NTB17-002
- Date Added:
- August 1, 2017
- Manufacturer:
- NISSAN
SummaryVOLUNTARY EMISSIONS SERVICE CAMPAIGN 2016-2017 ALTIMA ENGINE CONTROL MODULE REPROGRAM This bulletin applies only to vehicles equipped with 4-cylinder engines. INTRODUCTION Nissan is conducting a Voluntary Emissions Service Campaign on certain specific model year 2016 - 2017 Altima vehicles to reprogram the Engine Control Module (ECM). The reprogram will affect the operation of the grille shutters and will reduce under hood temperatures which, if not reprogrammed, could lead to a false Malfunction Indicator Lamp in some circumstances. The ECM will be reprogrammed at no charge to customers for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC514 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealer?' responsibility to check Service Comm for the campaign status on each vehicle falling within the range of this voluntary safety recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealer?s inventory. Federal law requires that new vehicles in dealer inventory which are the subject of a safety recall must be corrected prior to sale. Failure to do so can result in civil penalties by the National Highway Traffic Safety Administration. While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed.
Associated Products (2)Associated Documents - December 14, 2016•Document ID: 10109114Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- NTB16-123
- Date Added:
- August 1, 2017
- Manufacturer:
- NISSAN
SummaryPLASTIC INTERIOR TRIM PROTECTIVE COVERING REMOVAL SERVICE INFORMATION Vehicles are delivered with plastic interior trim protective covering on the front and rear seats, front and rear door panel finishers, steering wheel, and sun visors (see examples on page 2). When removing the protective covering, care must be used to avoid scuffs, scrapes, cuts, and other abrasive contact to interior trim components. DO NOT use sharp objects like razor blades, box cutters, knives, etc. when removing the plastic interior trim protective covering. IMPORTANT All soft trim described in this bulletin is on automatic return to NNA. Any trim found damaged in the way described in this bulletin will be charged back to the dealer.
Associated Products (32)2017 Nissan 370Z2017 Nissan Altima2017 Nissan Armada2017 Nissan Frontier2017 Nissan GT-R2017 Nissan Juke2017 Nissan Leaf2017 Nissan Maxima2017 Nissan Murano2017 Nissan Pathfinder2017 Nissan Quest2017 Nissan Rogue2017 Nissan Sentra2017 Nissan Titan2017 Nissan Versa2017 Nissan Versa Note2016 Nissan 370Z2016 Nissan Altima2016 Nissan Frontier2016 Nissan GT-R+ 12 moreAssociated Documents - December 9, 2016•Document ID: 10109117Service Bulletin/Repair InstructionsPOWER TRAIN; ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
- Mfr Comm. #:
- PC490 - 2013-16
- Date Added:
- August 1, 2017
- Manufacturer:
- NISSAN
SummaryCVT Reprogramming Voluntary Service Campaign ***** Campaign Summary***** Nissan is conducting a voluntary service campaign on approximately 1,657,666 specific MY2013-16 Altima (L33) and MY2014-16 Rogue (T32) vehicles to reprogram the Continuously Variable Transmission (CVT) software. Under specific driving conditions, hydraulic pressure may decrease and result in belt slip within the CVT. This may result in MIL illumination (P0776) and poor acceleration in some vehicles. There is no safety concern due to built-in fail-safe logic. Nissan is proactively reprogramming the CVT to prevent durability concerns and high out of warranty repair costs for owners. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm I.D. PC490. 2. Dealers are requested to repair any affected vehicles in dealer new or pre-owned inventory to ensure customer satisfaction. 3. Dealers should use NTB16-121 to correct any vehicles subject to this campaign. 4. Once repaired, dealers should submit the claim, using the claims coding provided, and release the vehicle.
Associated Products (7)Associated Documents - December 8, 2016•Document ID: 10109112Service Bulletin/Repair InstructionsPOWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- NTB16-121
- Date Added:
- August 1, 2017
- Manufacturer:
- NISSAN
SummaryVOLUNTARY SERVICE CAMPAIGN 2013-2016 ALTIMA AND 2014-2016 ROGUE; TCM REPROGRAMMING INTRODUCTION Nissan is conducting this voluntary service campaign to reprogram the Transmission Control Module (TCM) for the transmission on certain specific 2013-2016 Altima and 2014-2016 Rogue vehicles. This TCM reprogram will be performed at no charge for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC490 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer?s inventory.
Associated Products (7)Associated Documents - December 6, 2016•Document ID: 10109109Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- NTB16-117a
- Date Added:
- August 1, 2017
- Manufacturer:
- NISSAN
Summary2016-2017 ALTIMA; MIL ON WITH A/F RATIO SENSOR DTC(s) This bulletin applies only to models equipped with 4-cylinder engines. This bulletin has been amended. The Parts Information section has been corrected. Please discard previous versions of this bulletin.
Associated Products (2)Associated Documents - December 1, 2016•Document ID: 10119177Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- NTB16-030a
- Date Added:
- October 15, 2017
- Manufacturer:
- NISSAN
Summary2013-2016 ALTIMA WITH QR25DE ENGINE; MIL ON WITH DTC P0101 This bulletin applies only to models equipped with 4-cylinder engines. This bulletin has been amended throughout. Discard all previous versions of this bulletin.
Associated Products (4)Associated Documents - December 1, 2016•Document ID: 10119172Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
- Mfr Comm. #:
- NTB12-051k
- Date Added:
- October 15, 2017
- Manufacturer:
- NISSAN
SummaryMIL ON WITH DTC P0101 This bulletin has been amended. The APPLIED VEHICLES section on this page and Table A on page 7 have been updated. Discard all previous versions of this bulletin.
Associated Products (16)Associated Documents - December 1, 2016•Document ID: 10109110Service Bulletin/Repair InstructionsEQUIPMENT; STRUCTURE:BODY
- Mfr Comm. #:
- NTB16-119
- Date Added:
- August 1, 2017
- Manufacturer:
- NISSAN
Summary2013 ? 2016 ALTIMA; RUST AROUND REAR LICENSE LAMP FINISHER IF YOU CONFIRM When rust is found on the rear deck lid surface in the area surrounding the license lamp finisher (Figure 1) or replacing the license lamp finisher for any reason. ACTION - Replace the license lamp finisher with the new replacement part listed in the Parts Information. - Refer to the Electronic Service Manual (ESM), section EXT ? Exterior for removal and installation information. - Repair any damaged surfaces that were in direct contact with the license lamp finisher.
Associated Products (4)Associated Documents - November 30, 2016•Document ID: 10120596Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- NTB16-100
- Date Added:
- October 25, 2017
- Manufacturer:
- NISSAN
Summary20162016 NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE IF YOU CONFIRM: One or more of the following: - A status message ?Voice Recognition is initializing, please wait? is displayed when pressing the voice recognition button 2-3 minutes after the ignition is first turned ON. NOTE: If the message is displayed within the first 2-3 minutes this is normal. The voice recognition is loading phonebook contacts into its system. - A loud booming noise is emitted from the vehicle?s speaker while connected on a Bluetooth hands-free phone call. - The buttons on the navigation unit intermittently flicker. This is particularly noticeable at night when the buttons are illuminated. - Display night illumination is not automatically detected by the navigation unit. The center display screen illumination does not change at night when it is dark. - The navigation unit reboots (Nissan logo appears after loss of sound) only while listening to XM radio. And - The Software version has been confirmed as ?not current? (refer to page 3). ACTION: Perform the SERVICE PROCEDURE starting on page 2 and reprogram the Navigation system with USB memory stick listed on page 2.
Associated Products (2)Associated Documents - November 30, 2016•Document ID: 10119283Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- NTB16-117
- Date Added:
- October 15, 2017
- Manufacturer:
- NISSAN
Summary2016-2017 ALTIMA; MIL ON WITH A/F RATIO SENSOR DTC(s) IF YOU CONFIRM One or more of the following DTCs is stored: - P014C - A/F SENSOR1 (B1) (O2 sensor slow response - rich to lean bank 1 sensor 1) - P014D - A/F SENSOR1 (B1) (O2 sensor slow response - lean to rich bank 1 sensor 1) - P015A - A/F SENSOR1 (B1) (O2 sensor delayed response - rich to lean bank 1 sensor 1) - P015B - A/F SENSOR1 (B1) (O2 sensor delayed response - lean to rich bank 1 sensor 1) ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. If this bulletin applies: 2. Reprogram the ECM. 3. Replace the Air Fuel Ratio (A/F) Sensor 1. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
Associated Products (2)Associated Documents - November 29, 2016•Document ID: 10119266Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- NTB13-107a
- Date Added:
- October 15, 2017
- Manufacturer:
- NISSAN
SummaryINTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles and make changes to the body of the bulletin. Please discard previous versions.
Associated Products (21)2017 Nissan Altima2017 Nissan Maxima2017 Nissan Murano2017 Nissan Pathfinder2017 Nissan Rogue2017 Nissan Titan2016 Nissan Altima2016 Nissan Maxima2016 Nissan Murano2016 Nissan Pathfinder2016 Nissan Rogue2016 Nissan Titan2015 Nissan Altima2015 Nissan Murano2015 Nissan Pathfinder2015 Nissan Rogue2014 Nissan Altima2014 Nissan Pathfinder2014 Nissan Rogue2013 Nissan Altima+ 1 moreAssociated Documents - November 28, 2016•Document ID: 10119282Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- NTB16-116
- Date Added:
- October 15, 2017
- Manufacturer:
- NISSAN
SummaryNISSAN; DIAGNOSIS INFORMATION FOR ABS DTC C1130 SERVICE INFORMATION When diagnosing for DTC C1130 (ENGINE SIGNAL): ECM related DTCs (P-codes) must be diagnosed, repaired, and DTCs erased first. - DTC C1130 is an ABS DTC that indicates an output signal of the ECM is not recognized. - Absent or incorrect ECM signals, that are indicated by corresponding P-codes, may trigger C1130 in the ABS control unit. - Some vehicle features that can be affected by absent or incorrect ECM signals are: - Forward Emergency Braking (FEB) - Intelligent Cruise Control (ICC) - VDC/ABS/TCS
Associated Products (86)2017 Nissan 370Z2017 Nissan Altima2017 Nissan Armada2017 Nissan Frontier2017 Nissan Juke2017 Nissan Maxima2017 Nissan Murano2017 Nissan Pathfinder2017 Nissan Quest2017 Nissan Rogue2017 Nissan Sentra2017 Nissan Titan2017 Nissan Versa2017 Nissan Versa Note2016 Nissan 370Z2016 Nissan Altima2016 Nissan Frontier2016 Nissan Juke2016 Nissan Maxima2016 Nissan Murano+ 66 moreAssociated Documents - November 15, 2016•Document ID: 10119279Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- NTB16-112
- Date Added:
- October 15, 2017
- Manufacturer:
- NISSAN
Summary2013-2014 ALTIMA; A/C DOES NOT BLOW COLD AND CLUTCH DOES NOT ENGAGE IF YOU CONFIRM The air conditioner does not blow cold air, AND The magnet clutch is determined to be the cause when following the diagnosis procedure in the HAC section of the Electronic Service Manual (ESM). ACTION Replace the magnet coil. - Refer to SERVICE PROCEDURE on page 3. NOTE: Do NOT discharge the refrigerant or remove the A/C compressor for this procedure.
Associated Products (2)Associated Documents - November 14, 2016•Document ID: 10119277Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- NTB16-110
- Date Added:
- October 15, 2017
- Manufacturer:
- NISSAN
Summary2015-2016 ALTIMA; 4 CYLINDER WITH DTC P0776 STORED IF YOU CONFIRM The MIL is ON with DTC P0776 (PC SOLENOID B ? Pressure Control Solenoid ?B? Performance/Stuck OFF) stored. NOTE: If this issue should occur: - P1715 (INPUT SPEED SENSOR) may be stored with DTC P0776. - The vehicle may hesitate and/or have reduced power. ACTION - Refer to the Repair Flow Chart on page 2 for CVT repair. CAUTION: Always handle the CVT and component assemblies carefully and with the appropriate lifting tools. - Pages 53 and 82 must be printed and attached to the repair order.
Associated Products (2)Associated Documents - November 14, 2016•Document ID: 10119276Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- NTB15-086e
- Date Added:
- October 15, 2017
- Manufacturer:
- NISSAN
Summary2013-2014 ALTIMA AND 2014-2016 ROGUE; MIL ON WITH DTC P0776, P1715 MAY HAVE HESITATION AND/OR LACK OF POWER This bulletin has been amended to remove 2015-2016 Altima from the Applied Vehicles. Please discard previous versions of this bulletin.
Associated Products (5)Associated Documents - November 14, 2016•Document ID: 10119274Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- NTB15-049j
- Date Added:
- October 15, 2017
- Manufacturer:
- NISSAN
SummaryTELEMATICS SERVICE INFORMATION This bulletin has been amended. Information for 2017 Rogue and Rogue Hybrid has been applied. No other changes have been made. Please discard previous versions of this bulletin.
Associated Products (13)Associated Documents - October 26, 2016•Document ID: 10109139Service Bulletin/Repair InstructionsSTRUCTURE:BODY
- Mfr Comm. #:
- PC502 - 2017 Alt
- Date Added:
- August 1, 2017
- Manufacturer:
- NISSAN
SummaryFront Member Welds - Quality Assurance Hold ***** Detailed Information ***** Nissan is placing a temporary Quality Assurance (QA) Hold on approximately 880 specific MY2017 Altima (L33) and 296 specific MY2017 Maxima (A36) vehicles. Some of these vehicles were originally placed on hold on October 14, 2016 and subsequently released for sale on October 21, 2016. After further engineering and design review, Nissan has decided to reverse this decision and place these vehicles on hold again. Nissan is continuing to study the issue and expects to have further direction by the end of November 2016. The Service Comm I.D. has been changed to help clarify which vehicles should be held until further notice. ***** What Dealers Should Do ***** 1. Verify if vehicles currently in dealer inventory are affected by this QA Hold using Service Comm I.D. PC502 Note: Dealers should continue to check new arriving inventory for QA Hold applicability. 2. Please do not sell or trade the specific 2017 Altima and Maxima vehicles in dealer inventory subject to this QA Hold. 3. No further action is necessary at this time. Nissan will provide an update by the end of November 2016. Note: If a vehicle previously held and sold, there is no need to notify the customer at this time. If necessary, Nissan will contact affected customers.
Associated Products (2)Associated Documents - October 21, 2016•Document ID: 10120586Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- NTB13-077b
- Date Added:
- October 25, 2017
- Manufacturer:
- NISSAN
SummaryCVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.
Associated Products (33)2017 Nissan Altima2017 Nissan Maxima2017 Nissan Murano2017 Nissan Pathfinder2017 Nissan Sentra2017 Nissan Versa2017 Nissan Versa Note2016 Nissan Altima2016 Nissan Maxima2016 Nissan Murano2016 Nissan Pathfinder2016 Nissan Rogue2016 Nissan Sentra2016 Nissan Versa2016 Nissan Versa Note2015 Nissan Altima2015 Nissan Murano2015 Nissan Pathfinder2015 Nissan Rogue2015 Nissan Sentra+ 13 moreAssociated Documents