Nissan Rogue Service Bulletins (2014)
332 manufacturer communications on file.
- July 30, 2014•Document ID: 10056134Service Bulletin/Repair InstructionsBACK OVER PREVENTION: CAMERA SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- NTB-14-072
- Date Added:
- September 16, 2014
- Manufacturer:
- NISSAN
SummaryNISSAN: USE CORRECTED SPECIFICATION (SD) FOR POSITIONING TARGETS WHEN PERFORMING THE CALIBRATION FOR REAR VIEW CAMERA, THAT MONITORS TRAVELING LANE. MODEL 2014 ROGUE.
Associated Products (1)Associated Documents - July 15, 2014•Document ID: 10192406Service Bulletin/Repair InstructionsEQUIPMENT; ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- NTB14067
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummaryIF YOU CONFIRM The maintenance interval mileage in the Vehicle Information Display resets to zero with each ON > OFF > ON ignition cycle, ACTION Reprogram the Vehicle Information Display (METER/M&A) per the Service Procedure in this bulletin. See this bulletin for further detail.
Associated Products (1)Associated Documents - July 7, 2014•Document ID: 10192402Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM; ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE
- Mfr Comm. #:
- NTB14039A
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummarySERVICE INFORMATION If one or both Intelligent Keys cannot be located prior to customer delivery of an Applied Vehicle, refer to the applicable section of this bulletin for Intelligent Key registration instructions. - One (1) Intelligent Key Is Lost ---- Page 2 - Two (2) Intelligent Keys Are Lost ---- Page 3 NOTE - If both Intelligent Keys are lost with the BCM in Transit Mode, the BCM and ECM will need to be replaced. Refer to pages 3 - 5 for more information. See this bulletin for more detail.
Associated Products (1)Associated Documents - June 26, 2014•Document ID: 10192397Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER; EQUIPMENT
- Mfr Comm. #:
- PC304
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummaryNissan is conducting a dealer inventory inspection of the automatic climate control system operation on 910 specific 2014 Rogue vehicles identified in SERVICE COMM.
Associated Products (1)Associated Documents - June 24, 2014•Document ID: 10192394Service Bulletin/Repair InstructionsEQUIPMENT; ELECTRICAL SYSTEM
- Mfr Comm. #:
- NTB10066A
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummarySERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
Associated Products (156)2015 Nissan 370Z2015 Nissan Altima2015 Nissan GT-R2015 Nissan Leaf2015 Nissan Versa2015 Nissan Versa Note2014 Nissan 370Z2014 Nissan Altima2014 Nissan Armada2014 Nissan Cube2014 Nissan Frontier2014 Nissan GT-R2014 Nissan Juke2014 Nissan Leaf2014 Nissan Maxima2014 Nissan Murano2014 Nissan NV2014 Nissan NV2002014 Nissan Pathfinder2014 Nissan Quest+ 136 moreAssociated Documents - June 20, 2014•Document ID: 10192393Service Bulletin/Repair InstructionsEQUIPMENT; ELECTRICAL SYSTEM:IGNITION
- Mfr Comm. #:
- PC300A
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummaryThe original VIN list provided with the initial announcement contained 29 vehicles that are not equipped with push-button ignition. These 29 vehicles are exempt from the repair and are no longer subject to the quality hold.
Associated Products (1)Associated Documents - June 18, 2014•Document ID: 10192391Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; ELECTRICAL SYSTEM:IGNITION
- Mfr Comm. #:
- PC300
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummaryNissan is conducting a dealer inventory service action to replace the push button ignition switch on 158 specific 2014 Rogue vehicles identified in SERVICE COMM.
Associated Products (1)Associated Documents - June 18, 2014•Document ID: 10192390Service Bulletin/Repair InstructionsTIRES; EQUIPMENT
- Mfr Comm. #:
- NTB14055
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummarySERVICE INFORMATION For 2014 - 2015 Rogue (T32) equipped with third row seats: Do not install or add a spare tire to the vehicle. The vehicle is not designed to be equipped with a spare tire. See this bulletin for further detail.
Associated Products (2)Associated Documents - June 2, 2014•Document ID: 10192380Service Bulletin/Repair InstructionsFORWARD COLLISION AVOIDANCE; EQUIPMENT
- Mfr Comm. #:
- NTB14050
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummarySERVICE INFORMATION When performing Distance Sensor Alignment, use the corrected specification (L) for positioning the target board. NOTE: The Distance Sensor is used for the Forward Collision Warning (FCW) system. The specification in the ElectronicService Manual (ESM), Section DAS, Driver Assistance Systems, for positioning the Distance Sensor Target Board is incorrect. Use the corrected specification (L) listed in this bulletin.
Associated Products (1)Associated Documents - June 2, 2014•Document ID: 10055919Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
- Mfr Comm. #:
- NTB-14-050
- Date Added:
- August 5, 2014
- Manufacturer:
- NISSAN
SummaryNISSAN: THE POSITIONING OF DISTANCE SENSOR TARGET BOARD IS INCORRECT, IN ELECTRONIC SERVICE MANUAL (ESM), AND THE CORRECTED SPECIFICATION (L), IS USED TO PERFORM THE DISTANCE SENSOR ALIGNMENT. MODEL 2014 ROGUE. *PE
Associated Products (1)Associated Documents - May 23, 2014•Document ID: 10192374Service Bulletin/Repair InstructionsEQUIPMENT; WHEELS
- Mfr Comm. #:
- NTB14048
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummarySERVICE INFORMATION Factory wheel covers are installed on vehicles during Pre Delivery Inspection (PDI). Care must be taken to properly install the wheel covers to avoid damage. Go to SERVICE PROCEDURE in this bulletin for proper wheel cover installation. NOTE: Damage to wheel covers caused by improper installation is not covered under warranty. See this bulletin for further detail.
Associated Products (9)Associated Documents - May 22, 2014•Document ID: 10192373Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; STRUCTURE
- Mfr Comm. #:
- NTB14047
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummaryIF YOU CONFIRM: The "front door power window and door lock/unlock switch (RH) finisher" (switch finisher) has a loose fit, causting an excessive gap. See Figure 1. ACTION: 1. Remove the passenger front door finisher (door finisher). - Refer to the Electronic Service Manual (ESM), section INT-Interior, for removal procedure. 2. Install a foam block where shown in SERVICE PROCEDURE. - Use the foam block listed in PARTS INFORMATION. 3. Install the door finisher with a new switch finisher listed in PARTS INFORMATION. - Refer to the ESM, section INT-Interior, for installation procedure. See this bulletin for further detail.
Associated Products (1)Associated Documents - May 6, 2014•Document ID: 10192361Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ELECTRICAL SYSTEM
- Mfr Comm. #:
- NTB14038
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummarySERVICE INFORMATION When registering the Intelligent Keys (I-Keys) to a vehicle for one of the following concerns: * After replacing the BCM. Or * When one of the I-Keys has been lost and needs to be replaced. Or * When additional I-Keys are being added to the vehicle. Always use the following steps to insure proper registration of the I-Keys: 1. First Initialize the BCM. 2. Register all of the vehicle?s ?previously registered? I-Keys to the vehicle first. And then 3. Register any new (additional) I-Keys only after all of the pre-existing I-Keys have been registered. 4. Confirm operations of all I-Keys. Please see this bulletiln for further details.
Associated Products (5)Associated Documents - April 29, 2014•Document ID: 10192354Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:WIRING
- Mfr Comm. #:
- NTB14032
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummarySERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Nissan vehicles has changed. This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.
Associated Products (138)2017 Nissan 370Z2017 Nissan Altima2017 Nissan Armada2017 Nissan Frontier2017 Nissan GT-R2017 Nissan Juke2017 Nissan Leaf2017 Nissan Maxima2017 Nissan Murano2017 Nissan NV2002017 Nissan Pathfinder2017 Nissan Rogue2017 Nissan Sentra2017 Nissan Titan2017 Nissan Versa2016 Nissan 370Z2016 Nissan Altima2016 Nissan Frontier2016 Nissan GT-R2016 Nissan Juke+ 118 moreAssociated Documents - April 9, 2014•Document ID: 10192348Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- NTB14026
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummaryIF YOU CONFIRM: An electrical issue caused by corrosion in the Main Harness to Body Harness connectors located at the bottom of the driver side A-pillar: Connector numbers M13 to B3 and/or M14 to B4. ACTIONS: 1. Preform repairs to harness connectors as needed. 2. Apply Harness Protector to cover the harness connectors. See this bulletin for further detail.
Associated Products (7)Associated Documents - April 9, 2014•Document ID: 10055490Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- NTB-14-026
- Date Added:
- June 4, 2014
- Manufacturer:
- NISSAN
SummaryNISSAN: THE MAIN HARNESS TO BODY HARNESS CONNECTORS IS EXPERIENCING ELECTRICAL CORROSION ISSUES. 2008-2014 ROGUE. *PE
Associated Products (7)Associated Documents - April 4, 2014•Document ID: 10192344Service Bulletin/Repair InstructionsSTEERING; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
- Mfr Comm. #:
- NTB14021
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummaryIF YOU CONFIRM The Instrument Lower Panel LH (as shown in Figure 1) molded plastic clip will not stay secured. ACTION Install a shim between the Steering Member and the Instrument Panel and apply felt tape to the Instrument Lower Panel LH with the SERVICE PROCEDURE starting on page 2. Please see this bulletin for further details.
Associated Products (1)Associated Documents - March 27, 2014•Document ID: 10192341Service Bulletin/Repair InstructionsWHEELS; EQUIPMENT
- Mfr Comm. #:
- PC274
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummaryNissan is conducting a Dealer Inventory Inspection to inspect the right front and right rear lug nuts on 372 certain specific 2014 Nissan Rogue and Pathfinder vehicles currently in dealer inventory.
Associated Products (2)Associated Documents - March 26, 2014•Document ID: 10192339Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT
- Mfr Comm. #:
- PC266
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummaryNissan is conducting a customer satisfaction action on certain MY2014 Nissan Rogue SL AWD vehicles to send customers a Cargo Protector accessory that was inadvertently listed on the Monroney label but was not installed.
Associated Products (1)Associated Documents - March 21, 2014•Document ID: 10192337Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
- Mfr Comm. #:
- PC266OL
- Date Added:
- May 10, 2021
- Manufacturer:
- NISSAN
SummaryNissan is conducting a customer satisfaction action on certain MY2014 Nissan Rogue SL AWD vehicles to send customers a Cargo Protector accessory that was inadvertently listed on the Monroney label but was not installed.
Associated Products (1)Associated Documents