Mercedes-Benz G-Class Service Bulletins (2024)

129 manufacturer communications on file.

• May 22, 2025•Document ID: 11018626

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.85-P-079271

  Date Added:

  May 29, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint After a software update of HERMES communication module N112/9 has been performed on a gray import vehicle, the message "SOS - Service not activated" is displayed in the instrument cluster. Cause The message "SOS - Service not activated" tells the customer that "over-the-air" registration of the vehicle with the Mercedes Intelligent Cloud is not possible. On a gray import vehicle, this is due to the fact that the SIM card installed in the HERMES communications module cannot dial into the mobile phone network in the importing country. Remedy The only way of avoiding the message in the instrument cluster is to deactivate the HERMES module using the 09o deactivation process after obtaining the customer's consent. After deactivation, the HERMES control unit (N112/9) has the operating status "Inoperative". The message "SOS not ready" appears in the audio/COMAND display (A40/8) and may also appear in the instrument cluster. This display message tells the customer that the emergency call function is not available. In addition, the workshop must attach a label (2 x part number A9078172900 required) to the cover of the emergency call button in the overhead control panel and to the emergency call button itself. Replacing the hardware of the HERMES communication module is not effective.

  Associated Products (119)

  2024 Mercedes-Benz G-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLC-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz CLS-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz G-Class2022 Mercedes-Benz GLC-Class2021 Mercedes-Benz A-Class2021 Mercedes-Benz AMG GT2021 Mercedes-Benz C-Class2021 Mercedes-Benz CLS-Class2021 Mercedes-Benz E-Class2021 Mercedes-Benz G-Class2021 Mercedes-Benz GLC-Class2021 Mercedes-Benz S-Class2020 Mercedes-Benz A-Class2020 Mercedes-Benz AMG GT+ 99 more
  Associated Documents

  • DownloadMC-11018626-0001.pdf↗
• May 21, 2025•Document ID: 11019018

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI33.30-P-056665

  Date Added:

  June 3, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts

  Associated Products (274)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class+ 254 more
  Associated Documents

  • DownloadMC-11019018-0001.pdf↗
• May 2, 2025•Document ID: 11018206

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.10-P-071499

  Date Added:

  May 9, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint The result from the XENTRY battery test does not match the current state of the battery. Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy 1) If the battery is discharged, charge the battery. Review WS54.00-P-0037B for minimum charger specifications. • Note the amperage difference between trickle (maintainer) chargers of at least 16A and quick chargers of at least 30A. • Review AP54.10-P-5449U. Note when battery is sufficiently charged the charger current is less 5A. 2) While charging the battery, analyze the vehicle data to determine root cause of discharge using the following data points: • NOTE: For guidance on use of the on-board electrical data please review the AKUBIS video titled "New onboard electrical system diagnosis shown on BR 166". The video can be accessed through WIS by following the path WSM--> content by model series --> passenger cars --> ML-Class --> Model 166 --> group 54 --> New onboard electrical system diagnosis. • Refer to the March 2023 PCTT for the video walkthrough of analysis as well as the attachment of the slides to this Li. For Star 2 vehicles: -Review FSAM on-board electrical data conspicuous records • NOTE: This data can be found via FSAM N10/6 -> Actual Values -> On-board electrical system -> On-board electrical system data For Star 3 vehicles: -Review N73/3 EZS on-board electrical data conspicuous records • NOTE: This data can be found via EZS N73/3 -> Actual Values -> On-board electrical system -> On-board electrical system data 3) Determine if root cause is due to: • vehicle technical issue? • customer behavior? NOTE: Recommend using battery analysis sheet found in XiW -> Local Contents -> Diagnostic info -> Battery Discharge Worksheet 4) If battery still does not accept charge, create a TIPS case. -Must include with the case: • Amperage setting of charger and time battery was on charger • XENTRY Battery Tester results • Voltage of battery taken with multimeter: Do not connect charger while taking measurements • N10/6 FSAM and N73/3 EZS CUL • Workshop analysis of conspicuous data • Root cause analysis for battery discharge based on the above documents (technical, customer, etc.) • NOTE: For expedited results when creating a case write customer complaint as "XENTRY Battery Tester implausible".

  Associated Products (107)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class+ 87 more
  Associated Documents

  • DownloadMC-11018206-0001.pdf↗
• April 28, 2025•Document ID: 11017500

  Service Bulletin/Repair Instructions
  EXTERIOR LIGHTING

  Mfr Comm. #:

  LI82.10-P-078896

  Date Added:

  May 2, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. • If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.

  Associated Products (273)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class+ 253 more
  Associated Documents

  • DownloadMC-11017500-0001.pdf↗
• April 28, 2025•Document ID: 11017496

  Service Bulletin/Repair Instructions
  EXTERIOR LIGHTING

  Mfr Comm. #:

  LI82.10-P-078301

  Date Added:

  May 2, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Remedy NOTE: If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for damage. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078896 The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions.

  Associated Products (273)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class+ 253 more
  Associated Documents

  • DownloadMC-11017496-0001.pdf↗
• April 21, 2025•Document ID: 11017119

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.85-P-079087

  Date Added:

  April 22, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint A popup is seen on the HU with the message "data connection temporarily not available". Potentially affected functionalities in NTG4.5, NTG5 1.Weather 2.Local Search 3.IP Radio 4.Send2Car 5.Speech Detection Service 6.E-Navigator 7.iHeartRadio 8.Traffic Cams Cause Analysis ongoing. Remedy Please track the LI for further updates. Note: Please do not create TIPS cases. Please do not replace any components. HU/Hermes SW update / SCN coding will not fix the issue.

  Associated Products (88)

  2024 Mercedes-Benz G-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLC-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz G-Class2022 Mercedes-Benz GLC-Class2021 Mercedes-Benz C-Class2021 Mercedes-Benz E-Class2021 Mercedes-Benz G-Class2021 Mercedes-Benz GLC-Class2020 Mercedes-Benz C-Class2020 Mercedes-Benz E-Class2020 Mercedes-Benz G-Class2020 Mercedes-Benz GLA-Class2020 Mercedes-Benz GLC-Class2020 Mercedes-Benz S-Class2019 Mercedes-Benz C-Class+ 68 more
  Associated Documents

  • DownloadMC-11017119-0001.pdf↗
• April 15, 2025•Document ID: 11017225

  Emissions
  ELECTRICAL SYSTEM; ENGINE

  Mfr Comm. #:

  NCU - 2025030014

  Date Added:

  April 24, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (“MY”) 2023 – 2024 G-Class (463 platform) vehicles, the engine control unit software may not correspond to the current specifications. During vehicle idling and in the partial-load range CAT heating operating mode, the risk of cylinder misfire could increase, resulting in the illumination of the check engine Malfunction Indicator Lamp (‘MIL’). MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles.

  Associated Products (2)

  2024 Mercedes-Benz G-Class2023 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11017225-0001.pdf↗
• April 7, 2025•Document ID: 11017229

  Service Bulletin/Repair Instructions
  SERVICE BRAKES

  Mfr Comm. #:

  LI42.10-P-063502

  Date Added:

  April 25, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions and driving styles. Please refer to the Operator's Manual for further information such as care and maintenance instructions (washing vehicle directly after heavy use and using approved cleaning agents). These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. a) If the noises are coming from the front axle => Affix linings with adhesive film (see attachments for front axle). If backing plate is installed on pads, move to step 3. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfered Pads". 5. Apply heat-resistant lubricating paste to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 6. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle => Affix linings with adhesive film and grease the lining as per the specification (see attachments for rear axle). 1. Remove brake pads of rear axle. 2. Cleaning all contact points on brake lining and brake caliper/carrier. 3. Grease contact points (red areas) between brake lining and guide of brake caliper with heat-resistant lubricating paste. 4. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. 5. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfered Pads". IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off recouperation prior to bedding in brakes. d) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. e) Finally drive approx. 3 miles to allow the system to cool. f) Reassess noise.

  Associated Products (166)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz E-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT+ 146 more
  Associated Documents

  • DownloadMC-11017229-0001.pdf↗
• March 24, 2025•Document ID: 11016043

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI27.35-P-079039

  Date Added:

  March 27, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint A clicking/ticking/taping noise from underneath the vehicle with engine off during ECO stop event or after parking See video for example Cause Noise originates within the transmission valvebody Remedy Take a video from underneath vehicle recording the noise Pull EEPROM data, Inital Quick Test, and Control Unit Log Please open a TIPs case providing all data to assess next steps.

  Associated Products (90)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class+ 70 more
  Associated Documents

  • DownloadMC-11016043-0001.pdf↗
• March 7, 2025•Document ID: 11015663

  Over The Air
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  OTA - 5497748

  Date Added:

  March 17, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Issue Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the communication software does not correspond with the latest series production configuration. The communication module will receive an OTA update which includes quality-enhancing optimizations and improves the system stability and accessibility of Mercedes me services. The update is downloaded and installed in the background. During installation, the system can be used without restrictions. The new software will become active after the vehicle has been restarted. Remedy MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.

  Associated Products (56)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz S-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz S-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class+ 36 more
  Associated Documents

  • DownloadMC-11015663-0001.pdf↗
• March 5, 2025•Document ID: 11015673

  Over The Air
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  OTA - 5497828

  Date Added:

  March 17, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Issue Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the MBUX multimedia system software does not correspond with the latest series production configuration. The MBUX multimedia system software will receive an update to introduce new functions and improve the customer experience. Remedy MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.

  Associated Products (5)

  2025 Mercedes-Benz E-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11015673-0001.pdf↗
• March 5, 2025•Document ID: 11015640

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.70-P-077433

  Date Added:

  March 17, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: • It is recommended to replace the cover caps. • The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way.

  Associated Products (271)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class+ 251 more
  Associated Documents

  • DownloadMC-11015640-0001.pdf↗
• February 20, 2025•Document ID: 11014398

  Service Bulletin/Repair Instructions
  UNKNOWN OR OTHER

  Mfr Comm. #:

  LI00.01-P-078887

  Date Added:

  February 21, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint The intent of this document is to provide workshops with helpful technical reference language. • Commonly used acronyms in LI's and TIPS cases. • Control unit names, numbers, and how to identify. • Network/wiring architecture groups to baumuster quick reference. • Platform to baumuster quick reference. Cause Information only Remedy Acronyms: • AV = Actual Values • CU = Control Unit • CUL = Control Unit Log • DTC = Diagnostic Trouble Code • E-Stand = Fresh-up head unit boot software (found in head unit control unit log) • FUP = Fresh-up • FW = Firmware • HSVL = High Speed Video Line • HU = Head Unit • HW = Hardware • ISU = Initial Start Up • LVDS = Low Voltage Differential Signal • NSFT = Not Safe For Transport • MOPF = Model Facelift (Ex: 167 MOPF) • PiH = Plug-in Hybrid • P3 Hybrid = AMG Plug-in Hybrid with rear drive unit • SA Code = Sonderausstattungscode (Option Code) • SCN = Software Calibration Number • SW = Software • TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) • QT = Quicktest • XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. • Control Unit Name • Control Unit Number • Control Unit Short name • Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 • 117, 156, 246 (MFA) • 166, 176, 221, 242, 246, 292 Star 2 • 205, 213, 238, 253, 257, 290 (MRA) • 117, 156, 246 (MFA) • 118, 177, 243, 247 (MFA2) • 167, 222, 292, 463, 465, 906 Star 3 • 294, 295, 296, 297 (EVA2) • 206, 214, 223, 236, 254 (MRA2) • 192 and 232 (MSA) • 907 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": • 205 • 213 • 222 • 238 • 253 • 257 • 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": • 206 • 214 • 223 • 236 • 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 • 156 • 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" • 118 • 177 • 243 • 247 EVA1.5 = "Electric Vehicle Architecture" • 243 EVA2 = "Electric Vehicle Architecture - Generation 2" • 294 • 295 • 296 • 297 MSA = "Mercedes-Benz Sport Architecture" • 192 • 232 MMA = "Mercedes-Benz Modular Architecture" • No vehicles currently launched.

  Associated Products (83)

  2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class+ 63 more
  Associated Documents

  • DownloadMC-11014398-0001.pdf↗
• February 7, 2025•Document ID: 11014606

  Over The Air
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  OTA- 24P5497747

  Date Added:

  February 28, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-25 A-Class, C-Class, CLA, CLS, E-Class, G-Class, GLA, GLB, GLC, GT, and S-Class (118, 177, 205, 213, 217, 222, 238, 247, 253, 257, 290, 463 platform) vehicles, the communication software does not correspond with the latest series production configuration. The communication module will receive an OTA update which includes quality-enhancing optimizations and improves the system stability and accessibility of Mercedes me services. The update is downloaded and installed in the background. During installation, the system can be used without restrictions. The new software will become active after the vehicle has been restarted. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update. Parts Parts are not required

  Associated Products (58)

  2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz AMG GT+ 38 more
  Associated Documents

  • DownloadMC-11014606-0001.pdf↗
• February 3, 2025•Document ID: 11014412

  Service Bulletin/Repair Instructions
  SERVICE BRAKES

  Mfr Comm. #:

  LI42.10-P-063502

  Date Added:

  February 22, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions and driving styles. Please refer to the Operator's Manual for further information such as care and maintenance instructions (washing vehicle directly after heavy use and using approved cleaning agents). These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. 1. Beginning Diagnostics: a) Check whether, apart from this document, an additional document exists for the model series in question, and if so, work through it and then continue with1b. b) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). c) Check the affected system for component wear, mechanical damage or localized overheating damage. 1. Replace damaged components as necessary and re-assess noise concern. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). 2. Specific Axle Work: NOTE: If brake pad has a metal backing plate, there is no need to affix the adhesive film. a) If the noises are coming from the front axle => Affix linings with adhesive film (see attachments for front axle). If backing plate is installed on pads, move to step 3. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. For 6 piston calipers, only in the area of the center piston. For other piston caliper configurations less than 6, apply where the piston(s) makes contact with the back of the pad. 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfered Pads". 5. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle => Affix linings with adhesive film and grease the lining as per the specification (see attachments for rear axle). 1. Remove brake pads of rear axle. 2. Cleaning all contact points on brake lining and brake caliper/carrier. 3. Grease contact points (red areas) between brake lining and guide of brake caliper with heat-resistant lubricating paste. 4. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. 5. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfered Pads". IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. d) Finally drive approx. 3 miles to allow the system to cool. e) Reassess noise.

  Associated Products (157)

  2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class+ 137 more
  Associated Documents

  • DownloadMC-11014412-0001.pdf↗
• January 22, 2025•Document ID: 11013075

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI07.61-P-078629

  Date Added:

  January 24, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint After performing a software update either for recall campaign 2023070022 and/or 2022080005 or general course of diagnosis the vehicle will not start and/or the software flash will not complete. Cause Newer software releases are incompatible with older HW object numbers (ME part numbers). Remedy If a no start condition is encountered after a software update, check the ME and VGS control unit part numbers. Open an XSF ticket with the PN's and explain what software is attempting to be flashed. Afterwards continue with the repair as normal and quality check the vehicle. If any issues arise open a TIPS case and forward it to market support.

  Associated Products (6)

  2024 Mercedes-Benz G-Class2023 Mercedes-Benz G-Class2022 Mercedes-Benz G-Class2021 Mercedes-Benz G-Class2020 Mercedes-Benz G-Class2019 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11013075-0001.pdf↗
• January 18, 2025•Document ID: 11013081

  Service Bulletin/Repair Instructions
  SERVICE BRAKES

  Mfr Comm. #:

  LI42.10-P-063502

  Date Added:

  January 24, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions and driving styles. Please refer to the Operator's Manual for further information such as care and maintenance instructions (washing vehicle directly after heavy use and using approved cleaning agents). These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. 1. Beginning Diagnostics: a) Check whether, apart from this document, an additional document exists for the model series in question, and if so, work through it and then continue with1b. b) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). c) Check the affected system for component wear, mechanical damage or localized overheating damage. 1. Replace damaged components as necessary and re-assess noise concern. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). 2. Specific Axle Work: NOTE: If brake pad has a metal backing plate, there is no need to affix the adhesive film. a) If the noises are coming from the front axle => Affix linings with adhesive film (see attachments for front axle). If backing plate is installed on pads, move to step 3. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. For 6 piston calipers, only in the area of the center piston. For other piston caliper configurations less than 6, apply where the piston(s) makes contact with the back of the pad. 4. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle => Affix linings with adhesive film and grease the lining as per the specification (see attachments for rear axle). 1. Remove brake pads of rear axle. 2. Cleaning all contact points on brake lining and brake caliper/carrier. 3. Grease contact points (red areas) between brake lining and guide of brake caliper with heat-resistant lubricating paste. 4. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. d) Finally drive approx. 3 miles to allow the system to cool. e) Reassess noise.

  Associated Products (144)

  2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz AMG GT+ 124 more
  Associated Documents

  • DownloadMC-11013081-0001.pdf↗
• January 17, 2025•Document ID: 11013176

  Service Bulletin/Repair Instructions
  ENGINE; ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI07.61-P-076755

  Date Added:

  January 28, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Customer complains that CEL is active in instrument cluster. May also report rough running. Cause Software Remedy Please update the ME control unit software to the latest version. Ensure that a sensor rotor adaptation is conducted afterwards per the instructions in Xentry. Perform an AMG engine adaptation after the update and the sensor rotor adaptation. Assess the vehicle afterwards and if the complaint is remedied, release the vehicle. If the customer complaint is not remedied, process the vehicle via LI07.61-P-070707 and open a TIPS case with your findings. If the vehicle is already at the latest ME software level or if software is not available, process the vehicle via LI07.61- P-070707 and open a TIPS case with your findings.

  Associated Products (6)

  2024 Mercedes-Benz G-Class2023 Mercedes-Benz G-Class2022 Mercedes-Benz G-Class2021 Mercedes-Benz G-Class2020 Mercedes-Benz G-Class2019 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11013176-0001.pdf↗
• January 17, 2025•Document ID: 11013175

  Service Bulletin/Repair Instructions
  ENGINE

  Mfr Comm. #:

  LI07.61-P-070707

  Date Added:

  January 28, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint The customer complains of a check engine light (CEL) on. May also complain of the engine running roughly and/or a loss of power. Cause Multiple Causes Remedy Please see the document "Remedy Instructions" in attachments. For MY19-24 G63 there may be an alternate solution available, please reference LI07.61-P-076755 before performing the steps in this LI for MY19-24 G63 vehicles.

  Associated Products (57)

  2024 Mercedes-Benz AMG GT2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz G-Class2022 Mercedes-Benz GLC-Class2022 Mercedes-Benz GLE-Class2022 Mercedes-Benz GLS-Class2022 Mercedes-Benz S-Class+ 37 more
  Associated Documents

  • DownloadMC-11013175-0001.pdf↗
• January 16, 2025•Document ID: 11012904

  Service Bulletin/Repair Instructions
  SERVICE BRAKES

  Mfr Comm. #:

  LI42.10-P-063502

  Date Added:

  January 16, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions and driving styles. Please refer to the Operator's Manual for further information such as care and maintenance instructions (washing vehicle directly after heavy use and using approved cleaning agents). These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. 1. Beginning Diagnostics: a) Check whether, apart from this document, an additional document exists for the model series in question, and if so, work through it. b) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). c) Check the affected system for component wear, mechanical damage or localized overheating damage. 1. Replace damaged components as necessary and re-assess noise concern. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). 2. Specific Axle Work: a) If the noises are coming from the front axle => Affix linings with adhesive film (see attachments for front axle). 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. For 6 piston calipers, only in the area of the center piston. For other piston caliper configurations less than 6, apply where the piston(s) makes contact with the back of the pad. 4. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle => Affix linings with adhesive film and grease the lining as per the specification (see attachments for rear axle). 1. Remove brake pads of rear axle. 2. Cleaning all contact points on brake lining and brake caliper/carrier. 3. Grease contact points (red areas) between brake lining and guide of brake caliper with heat-resistant lubricating paste. 4. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. 5. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. d) Finally drive approx. 3 miles to allow the system to cool. e) Reassess noise.

  Associated Products (150)

  2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class+ 130 more
  Associated Documents

  • DownloadMC-11012904-0001.pdf↗