Mercedes-Benz AMG GT Service Bulletins

426 manufacturer communications on file.

• October 14, 2025•Document ID: 11024358

  Service Bulletin/Repair Instructions
  WHEELS; SUSPENSION

  Mfr Comm. #:

  LI40.10-P-059248

  Date Added:

  October 17, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Crackling and cracking noise from the outer wheel on the front axle when cornering Cause The noise is generated by a micromovement on the contact surface between the rim and the brake disk (wheel bolt group) and may be intensified by potential soiling. The more lightweight rim (AMG forged rim) transmits the noise louder; in the case of cast rims, the noise is generally not perceptible. This is not a technical defect, but rather a complaint concerning comfort. Safe operation of the vehicle is ensured at all times. Remedy Important note: The operations described below do not represent a permanent remedy in every case. The noise may reoccur again after an indefinite period of time; sanding the rims with abrasive media multiple times is not permissible. Only cleaning using the Hazet tool 4960-160 (recommendation) can be performed without any concerns each time the wheel is changed or if the complaint reoccurs. Replacing the parts (rim, wheel bolts, wheel bearings, wheel hub, brake disk) is not expedient in the event of this complaint. Clean the components of the wheel bolt connection according to the WIS instructions Sand down the rim and brake disk bowl by performing the following steps: • Manually sand rim (old design only) in area of water drain bores (Figure 1; item A), approx. 1.5 cm left and right of water drain bore (Figure 2) Note: Use abrasive paper with grit size 80. The grooving in this area should no longer be visible (sand down approx. 0.1-0.2mm) • Also sand brake disk bowl using emery cloth or abrasive paper with a grain size of 120 • For vehicles equipped with the AMG ceramic brake system (B07), abrasive paper may not be used for cleaning on the brake disk side Note: Do not use any cleaning agent when cleaning on the rim side. Cleaning using abrasive paper with a grain size of 80 will suffice. Do not apply any grease, lubricant or paste after cleaning The brake disk bowl should be "bare metal" in the area of the imprints made by the hole (Figure 3)

  Associated Products (55)

  2026 Mercedes-Benz AMG GT2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz C-Class2022 Mercedes-Benz GLC-Class2022 Mercedes-Benz GLE-Class+ 35 more
  Associated Documents

  • DownloadMC-11024358-0001.pdf↗
• October 11, 2025•Document ID: 11024224

  Service Campaign
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  NCU - 2024090007

  Date Added:

  October 10, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the engine control unit software does not correspond to current production specifications. As a consequence, the functionality of the post-catalyst oxygen sensor may be impaired due to increased thermal loading. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the engine control unit software.

  Associated Products (25)

  2023 Mercedes-Benz AMG GT2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz CLS-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz GLE-Class2022 Mercedes-Benz GLS-Class2021 Mercedes-Benz AMG GT2021 Mercedes-Benz CLS-Class2021 Mercedes-Benz E-Class2021 Mercedes-Benz GLE-Class2021 Mercedes-Benz GLS-Class2020 Mercedes-Benz AMG GT2020 Mercedes-Benz CLS-Class2020 Mercedes-Benz E-Class2020 Mercedes-Benz GLE-Class2020 Mercedes-Benz GLS-Class+ 5 more
  Associated Documents

  • DownloadMC-11024224-0001.pdf↗
• October 7, 2025•Document ID: 11024013

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI35.31-P-079847

  Date Added:

  October 7, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Complaints of oil leaking from rear differential oil pan area. Cause In the groove where the pan seal is placed, there may be imperfections (porosity) in the casting causing fluid to leak past the seal. The supplier states this only affects rear differentials with 2023 production date. The production date can be found stamped on the housing cover (see attachment). Remedy 1. Follow the attached instructions to inspect the rear differential cover for porosity. 2. Repair the vehicle with the applicable repair kit for the chassis. - The new oil pans that come with the repair kit should be produced in 2024 and not have this issue. *When submitting the claim, please reference this LI document and if porosity was found.*

  Associated Products (18)

  2026 Mercedes-Benz AMG GT2025 Mercedes-Benz AMG GT2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz GLE-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz GLE-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz GLE-Class2021 Mercedes-Benz AMG GT2021 Mercedes-Benz GLE-Class2020 Mercedes-Benz AMG GT2020 Mercedes-Benz GLE-Class2019 Mercedes-Benz AMG GT2019 Mercedes-Benz GLE-Class2018 Mercedes-Benz GLE-Class2017 Mercedes-Benz GLE-Class2016 Mercedes-Benz GLE-Class
  Associated Documents

  • DownloadMC-11024013-0001.pdf↗
• September 26, 2025•Document ID: 11023364

  Service Campaign
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  NCU - 2025090010

  Date Added:

  September 26, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Issue Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the Electronic Ignition Lock control unit coding does not correspond to current series production configuration. As a result, battery management could be affected and cause low battery voltage. A 12V battery message may appear in the instrument cluster after the vehicle has been dormant for an extended period of time. Remedy MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will SCN code the Electronic Ignition Lock control unit. The new SCN coding improves battery management, improving the efficiency of the 12V electrical system.

  Associated Products (7)

  2026 Mercedes-Benz AMG GT2025 Mercedes-Benz AMG GT2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz SL-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz SL-Class
  Associated Documents

  • DownloadMC-11023364-0001.pdf↗
• September 25, 2025•Document ID: 11023347

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.10-P-071499

  Date Added:

  September 25, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint The result from the XENTRY battery test does not match the current state of the battery. Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy 1) If the battery is discharged, charge the battery. Review WS54.00-P-0037B for minimum charger specifications. • Note the amperage difference between trickle (maintainer) chargers of at least 16A and quick chargers of at least 30A. • Review AP54.10-P-5449U. Note when battery is sufficiently charged the charger current is less 5A. 2) While charging the battery, analyze the vehicle data to determine root cause of discharge using the following data points: • NOTE: For guidance on use of the on-board electrical data please review the AKUBIS video titled "New onboard electrical system diagnosis shown on BR 166". The video can be accessed through WIS by following the path WSM--> content by model series --> passenger cars --> ML-Class --> Model 166 --> group 54 --> New onboard electrical system diagnosis. • Refer to the March 2023 PCTT for the video walkthrough of analysis as well as the attachment of the slides to this Li. • Review GF54.10-P-1012A regarding what can cause deep discharge protection to not end a battery draw. • Review SI54.10-P-0024A for proper maintenance of the vehicle. For Star 2 vehicles: -Review FSAM on-board electrical data conspicuous records • NOTE: This data can be found via FSAM N10/6 -> Actual Values -> On-board electrical system -> On-board electrical system data For Star 3 vehicles: -Review N73/3 EZS on-board electrical data conspicuous records • NOTE: This data can be found via EZS N73/3 -> Actual Values -> On-board electrical system -> On-board electrical system data 3) Determine if root cause is due to: • vehicle technical issue? • customer behavior? NOTE: Recommend using battery analysis sheet found in XiW -> Local Contents -> Diagnostic info -> Battery Discharge Worksheet 4) If battery still does not accept charge AND the vehicle does not fall within the parameters of improper maintenance, then create a TIPS case. *IMPORTANT* - If the improper maintenance/use is found during diagnosis, DO NOT open a TIPS case. If a TIPS case is opened, it will be marked 1 star and directed to your assigned FSE for review. TIPS Case must include with the case: • Amperage setting of charger and time battery was on charger • XENTRY Battery Tester results • Voltage of battery taken with multimeter: Do not connect charger while taking measurements • N10/6 FSAM, (N73 or N73/3) and (N73*1 or N73/3*1) • Workshop analysis of conspicuous data • Root cause analysis for battery discharge based on the above documents (technical, customer, etc.) • NOTE: For expedited results when creating a case write customer complaint as "XENTRY Battery Tester implausible".

  Associated Products (114)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLC-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE+ 94 more
  Associated Documents

  • DownloadMC-11023347-0001.pdf↗
• September 19, 2025•Document ID: 11023264

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.10-P-069698

  Date Added:

  September 22, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  See Attachment

  Associated Products (25)

  2026 Mercedes-Benz AMG GT2025 Mercedes-Benz AMG GT2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz GLE-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLE-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz CLS-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz GLE-Class2021 Mercedes-Benz AMG GT2021 Mercedes-Benz CLS-Class2021 Mercedes-Benz E-Class2021 Mercedes-Benz GLE-Class2020 Mercedes-Benz AMG GT2020 Mercedes-Benz CLS-Class2020 Mercedes-Benz E-Class+ 5 more
  Associated Documents

  • DownloadMC-11023264-0001.pdf↗
• September 17, 2025•Document ID: 11023193

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI27.19-P-072588

  Date Added:

  September 18, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy For vehicles with 722.9 transmission: Ensure LI54.15-P-057373 is performed before replacing any component parts. After processing and complying with the above document(s): 1. Perform an ignition reset on Y3/8n4 (VGS) 2. Inspect transmission connector for loose connections, damaged wiring or pins and any other concerns If communication with the VGS cannot be established, the complete valve body ('electrohydraulic controller unit (EHS)') must be replaced. Installation of a VGS repair kit is not permitted in this case as it is not possible to transfer the necessary valve characteristics without communication with the original control unit.

  Associated Products (143)

  2026 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class+ 123 more
  Associated Documents

  • DownloadMC-11023193-0001.pdf↗
• September 16, 2025•Document ID: 11023194

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.10-P-079772

  Date Added:

  September 18, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint After a software update from campaign 2025050001 of component LIB48_222 - G1/3 (48 V on-board electrical system battery) from software release A 000 902 50 48 to software release A 000 902 15 89, the fault code B183319 may be output. B183319 "The battery for the 48V on-board electrical system has a malfunction. The limit value for current has been exceeded" Cause Anomaly in the software update Remedy Please perform the following steps in the specified sequence: 1.) Delete fault codes 2.) Disconnect XENTRY Diagnosis and the 12 V battery charger 3.) Disconnect ground cable from the 12 V battery 4.) Ensure bus idle for at least 10 minutes 5.) Re-connect ground cable to the 12 V battery 6.) Delete fault codes again 7.) Perform a test drive 8.) Check fault codes > If fault code B183319 is still current, continue with the guided fault analysis in XENTRY Diagnosis. > If fault code B183319 goes to stored and can be cleared, no further action is required.

  Associated Products (48)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz GLC-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz C-Class+ 28 more
  Associated Documents

  • DownloadMC-11023194-0001.pdf↗
• September 16, 2025•Document ID: 11023192

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI00.00-P-079603

  Date Added:

  September 17, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint The OTA software update prepares the SRS/ORC controller and enables it to be updated remotely in the future. Based on technician feedback, the OTA (code: 25P5496529) does not start even after an extended period of time and several driving cycles. In addition, the "Continue" button is grayed out. Cause The exact cause for the OTA not to start is currently under analysis. Remedy Please check whether the vehicle is affected by the field measure "Update software of Supplemental Restraint System (SRS) control unit" (code: 25P5496529) and if yes, perform this update using a XENTRY with all latest Add-Ons and bill under accounting number 5496529. If the vehicle is not affected by this field measure, in the event of a complaint update control unit ORC223 (N2/5 -Supplemental Restraint System SRS) using XENTRY and use damage code 8251M01. As of XENTRY Release Version 06/25, control unit ORC223 can also be updated in this context without a password. Provided control unit ORC223 is error-free after the update, the vehicle can be handed back. ***IMPORTANT*** -In isolated cases, the OTA update may continue to be displayed for up to 3-4 weeks even after flashing with XENTRY. Note: This LI applies only to the OTA update for occupant protection!

  Associated Products (8)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz S-Class2023 Mercedes-Benz S-Class
  Associated Documents

  • DownloadMC-11023192-0001.pdf↗
• September 13, 2025•Document ID: 11023107

  Service Campaign
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  NCU - 2025080007

  Date Added:

  September 12, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Issue Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the High Voltage Battery (“HVB”) AC charger software does not correspond to current production specifications. As a consequence, a HVB MIL may illuminate during charging due to fluctuations in power consumption of the charging socket actuator. Remedy MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the HVB AC Charger Software.

  Associated Products (22)

  2025 Mercedes-Benz C-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz C-Class2022 Mercedes-Benz S-Class2022 Mercedes-Benz SL-Class2021 Mercedes-Benz AMG GT2021 Mercedes-Benz S-Class+ 2 more
  Associated Documents

  • DownloadMC-11023107-0001.pdf↗
• September 11, 2025•Document ID: 11023103

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.10-P-079772

  Date Added:

  September 12, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint After a software update of component LIB48_222 - G1/3 (48 V on-board electrical system battery) from software release A 000 902 50 48 to software release A 000 902 15 89, the fault code B183319 may be output. B183319 "The battery for the 48V on-board electrical system has a malfunction. The limit value for current has been exceeded" Cause Anomaly in the software update Remedy Please perform the following steps in the specified sequence: 1.) Delete fault codes 2.) Disconnect XENTRY Diagnosis and the 12 V battery charger 3.) Disconnect ground cable from the 12 V battery 4.) Ensure bus idle for at least 10 minutes 5.) Re-connect ground cable to the 12 V battery 6.) Delete fault codes again 7.) Perform a test drive 8.) Check fault codes > If fault code B183319 is still current, continue with the guided fault analysis in XENTRY Diagnosis. > If fault code B183319 goes to stored and can be cleared, no further action is required.

  Associated Products (41)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz CLS-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz GLE-Class2022 Mercedes-Benz GLS-Class2021 Mercedes-Benz AMG GT2021 Mercedes-Benz CLS-Class2021 Mercedes-Benz E-Class2021 Mercedes-Benz GLE-Class+ 21 more
  Associated Documents

  • DownloadMC-11023103-0001.pdf↗
• September 8, 2025•Document ID: 11023033

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI00.00-P-079603

  Date Added:

  September 9, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint The OTA software update prepares the SRS/ORC controller and enables it to be updated remotely in the future. Based on technician feedback, the OTA (code: 25P5496529) does not start even after an extended period of time and several driving cycles. In addition, the "Continue" button is grayed out. Cause The exact cause for the OTA not to start is currently under analysis. Remedy Please check whether the vehicle is affected by the field measure "Update software of Supplemental Restraint System (SRS) control unit" (code: 25P5496529) and if yes, perform this update using a XENTRY with all latest Add-Ons and bill under accounting number 5496529. If the vehicle is not affected by this field measure, in the event of a complaint update control unit ORC223 using XENTRY and use damage code 8251M01. As of XENTRY Release Version 06/25, control unit ORC223 can also be updated in this context without a password. Provided control unit ORC223 is error-free after the update, the vehicle can be handed back. ***IMPORTANT*** -In isolated cases, the OTA update may continue to be displayed for up to 3-4 weeks even after flashing with XENTRY. Note: This LI applies only to the OTA update for occupant protection!

  Associated Products (12)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz S-Class2021 Mercedes-Benz GLC-Class2020 Mercedes-Benz C-Class2020 Mercedes-Benz GLC-Class
  Associated Documents

  • DownloadMC-11023033-0001.pdf↗
• September 5, 2025•Document ID: 11022819

  Over The Air
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  OTA - 20250905

  Date Added:

  September 5, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, there is a new software release for the MBUX Infotainment system. An OTA update will enhance both functionality and entertainment features. The update introduces Dolby Atmos support for in-car apps, improvements to the MBUX calendar app, and the launch of MBUX SOUND DRIVE. To deliver a better music streaming experience, new apps will be installed and existing integrations with online streaming providers will be removed. Each provider will now require a separate app, which will be installed during the update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.

  Associated Products (11)

  2026 Mercedes-Benz GLC-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz SL-Class
  Associated Documents

  • DownloadMC-11022819-0001.pdf↗
• September 3, 2025•Document ID: 11022910

  Service Bulletin/Repair Instructions
  STRUCTURE:BODY

  Mfr Comm. #:

  LI61.20-P-077105

  Date Added:

  September 8, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Cracking/clicking noise from underbody when driving slowly (around curves); see attachment. Cause Potential causes: • Assembly of the underfloor paneling with unloaded body (results in tension after compression of vehicle in K0- design level) • Relative movement between front and rear engine compartment lining • Torque loss of the screw connection • Accumulation of stones and dirt Remedy Changes Made: • Screw connection in K0-design level (vehicle compressed - on ground at ride height) and taking into account the correct screw sequence • Additional screw connection points (minimization of relative movement) • Use of rivet nuts and screws with a larger diameter • Integration of spacer rings (reduction of accumulation of stones and dirt) Note: In order to rule out that other component parts may be responsible for the noise, remove the underfloor paneling first. If the noise complaint is NOT present after removal, proceed with underfloor paneling rework. Underfloor paneling rework 1. Order after-sales kit with item number A2326207003 for the rework. 2. After receiving the after-sales kit (A2326207003), check the contents: 22 screws (A0109902604) / 14 rivet nuts (A0009902349) / 4 spacer washers (A2326207203). If the content is complete, start rework in the next step. 3. Disassemble underfloor paneling. If front and rear engine compartment lining are bonded to one another, order new parts (A2326201101, A2326268900). 4. Clean underfloor paneling and integral carrier. Failure to clean the parts can lead to noise once re-assembled. 5. Mark four additional screw connection points on the front engine compartment lining (see attachment 1). See appendix 2 for dimensions. 6. Drill holes with d=9 mm on the markings. 7. Screw front and rear engine compartment lining together using the screw connection points already available (see attachment 3). Both linings are therefore aligned to one another. Important: Pay attention to alignment of the elongated holes on the external edges. 8. Drill into the rear engine compartment lining using the four additional holes with d=9 mm (see attachment 4). 9. Disassemble front and rear engine compartment lining. 10. Drill out three existing rivet nuts with d=9 mm (see attachment 5). 11. Insert seven new rivet nuts (A0009902349) (see attachment 6). 12. Drill out seven existing rivet nuts in the integral carrier with d=9 mm (see attachment 7). Caution: Do not damage integral carrier. 13. Remove remaining rivets that have fallen off from the integral carrier using a magnetic tube (see attachment 8). 14. Insert new rivet nuts (A0009902349) in the integral carrier (see attachment 9). 15. Fix four spacer rings (A2326207203) in place using bonding points between underfloor paneling and integral carrier (for position, see attachment 10 and attachment 11). Caution: No adhesive can be applied to the contact areas (risk of torque loss). 16. Install underfloor paneling on vehicle with 14 Nm (observe screw sequence in attachment 12). Important: Use screw item number A0109902604. If there are any issues or concerns, please open a TIPS case and send to the Body/Chassis/Entertainment inbox.

  Associated Products (4)

  2024 Mercedes-Benz AMG GT2024 Mercedes-Benz SL-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz SL-Class
  Associated Documents

  • DownloadMC-11022910-0001.pdf↗
• August 29, 2025•Document ID: 11022209

  Service Campaign
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  NCU - 2025080003

  Date Added:

  August 28, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the Battery Management System control unit software does not correspond to current production specifications. As a result, the battery Malfunction Indicator Lamp (MIL) may illuminate when no system fault occurs. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the Battery Management System control unit software.

  Associated Products (7)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz SL-Class
  Associated Documents

  • DownloadMC-11022209-0001.pdf↗
• August 29, 2025•Document ID: 11022204

  Over The Air
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  OTA - 20250829

  Date Added:

  August 28, 2025

  Manufacturer:

  MERCEDES-MAYBACH

  Summary

  Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the charging function does not correspond to the current series production configuration. The charging system software will be updated to stabilize the charging function of the vehicle. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.

  Associated Products (14)

  2025 Mercedes-Benz C-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class
  Associated Documents

  • DownloadMC-11022204-0001.pdf↗
• August 9, 2025•Document ID: 11021892

  Service Bulletin/Repair Instructions
  ENGINE

  Mfr Comm. #:

  LI15.40-P-077947

  Date Added:

  August 15, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Combustion engine could no longer be started, only electric driving possible Cause High-voltage belt-driven starter-alternator defective Remedy Requirement: Before carrying out test work, it must be ensured that the person performing the work has successfully completed the required qualification for work on the high-voltage system. Note: In order to check whether the high-voltage belt-driven starter-alternator is defective, please carry out the test below. If the fault "P0E2F00 The electrical fuse B for the high voltage has a malfunction" is stored in the N82/10 BMS control unit, the HV protocol must be checked to see whether the fuse for the auxiliary consumers is defective. In this case, the high-voltage battery must be replaced after the short circuit has been eliminated. (See attachment) The defective high-voltage belt-driven starter-alternator must always be sent back via the existing return delivery process for analysis. Check: Please disconnect the high-voltage plug at the high-voltage belt-driven starter-alternator and connect test adapter 000 589 94 63 00. Measure resistance HV+ to HV-. If the final measurement result is between 0–1 ohm, the high-voltage belt-driven starter-alternator with the short circuit must be replaced. If either one of or both the fault codes P0C0B16 and P0C0B17 are saved in the high-voltage belt-driven starter-alternator control unit G2/3, please replace the high-voltage belt-driven starter-alternator, since no short circuit can be measured here and this therefore concerns a hardware defect. Please check the serial number on the silver adhesive label below the SW number on the front of the high-voltage belt-driven starter-alternator. Example: 2314300044 (the first 10 digits, see attachment) Important note: If the number is greater than 2329100027, a TIPS case must be created. In this instance, please attach the following documents to the TIPS case: • Quick test • High-voltage event log • Picture of the silver adhesive label on the front of the high-voltage belt-driven starter-alternator (serial number) • Attach the measurement results with pictures

  Associated Products (6)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz S-Class
  Associated Documents

  • DownloadMC-11021892-0001.pdf↗
• August 5, 2025•Document ID: 11022056

  Service Bulletin/Repair Instructions
  STEERING

  Mfr Comm. #:

  LI46.10-P-079582

  Date Added:

  August 21, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Valeo Steering Column Module (N80) goes into bootloader after updating software to A2239028729. To verify the supplier and software number of the steering column module. See attachment "Supplier Identification" for assistance. Cause MRSM/SCCM flashed to SW A2239028729 Remedy Please send VIN specific ID1 Support Package online using the XENTRY Kit used during the time the error occurred. Then, create an XSS ticket using the Support Tool icon under XENTRY Diagnosis.

  Associated Products (18)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz SL-Class
  Associated Documents

  • DownloadMC-11022056-0001.pdf↗
• August 5, 2025•Document ID: 11021821

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.18-P-079535

  Date Added:

  August 13, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Vehicle does not start, can also not be driven electrically. The following fault messages are displayed in the instrument cluster: Red fault message "HV battery" with the addition "Towing not possible" Vehicle start not possible in yellow Cause Plug X292x1 / X296x1 not engaged correctly or plug defective. Remedy Requirement: Before carrying out test work, it must be ensured that the person performing the work has successfully completed the required qualification for work on the high-voltage system. Test: Check plug X292x1 / X296x1 as follows: Please first take a photo of the plug X292x1 / X296x1 before carrying out further checks. If a gap can be seen between the outer housing and plug housing of the plug X292x1 / X296x1, the plug X292x1 / X296x1 is not engaged correctly, see "Plug assembly" Annex. Please open a TIPS case and attach a photo of plug X292x1 / X296x1. Disconnect the plug X292x1 / X296x1 and try to shift the outer housing with the interlock plug above forward in a disconnected state. If this is not possible, the plug X292x1 / X296x1 is OK, see video "Check plug X292x1_X296x1_OK state" in Annex. If this check confirms that the outer housing can be shifted forward despite the disconnected plug X292x1 / X296x1, the plug X292x1 / X296x1 including wiring harness is not OK (please attach video) and must be replaced. Please attach a photo of the label to the TIPS case, see Annex "Position of label" Assembly: If the outer housing cannot be shifted forward after the check above, then the plug X292x1 / X296x1 can be installed properly as per the "Plug assembly" instructions, see Annex. Important note: If the plug was installed correctly, no gap between the outer housing and plug housing must be visible, see picture 5 from "Plug assembly" instructions Annex. There is no additional engaging for the outer housing. In addition, the plug X292x1 / X296x1 must be fixed in place with a cable tie, see "Gap / cable tie note" picture in the Annex.

  Associated Products (2)

  2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class
  Associated Documents

  • DownloadMC-11021821-0001.pdf↗
• August 1, 2025•Document ID: 11021142

  Service Bulletin/Repair Instructions
  SERVICE BRAKES

  Mfr Comm. #:

  LI42.10-P-063502

  Date Added:

  August 1, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy The intent of this document is to reduce or eliminate noise from high performance AMG brakes. AMG brakes are designed for performance under high load and in certain scenarios, can emit noise. Some of the scenarios are: • Driving style • Brake pressure and application style (stop-and-go traffic with consistent low brake pressure “riding brakes” where the brakes cannot cool sufficiently between applications). • Ambient temperatures 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. Continue with applying chamfer and Molykote as instructed below. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! a) If the noises are coming from the front axle. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining backing plate, including the brake lining guide pins and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". 4. Be sure to remove both brown paper backing sides of the adhesive film, it is double sided adhesive film. 5. If adhesive is already installed on backing plate where pistons contact the back of the pad, you may gently scrape off and re-apply a new adhesive or Molykote. Must not apply the Molykote on top of the adhesive. 6. Chamfer edges (gently round off sharp leading edges) on brake pads. Some pads have vertical grooves, these can be gently chamfered with a triangular file as well. See picture "Chamfering Technique". 7. Apply Molykote to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 8. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle. 1. Remove brake pads of rear axle. 2. Clean all contact points on brake lining backing plate and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfering Technique". 5. Grease contact points (red areas on attachment "Rear Pad Grease Area") between brake lining and guide of brake caliper with Molykote. 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off recouperation prior to bedding in brakes. d) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake application

  Associated Products (105)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz SL-Class+ 85 more
  Associated Documents

  • DownloadMC-11021142-0001.pdf↗