Mazda MX-30 Service Bulletins
302 manufacturer communications on file.
- January 5, 2023•Document ID: 10230892Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 07-001-23
- Date Added:
- February 2, 2023
- Manufacturer:
- MAZDA
SummarySome customers may complain about insufficient heater performance under -4 degree F (-20 degree C) or colder environment. This is caused when the air conditioner is set to the defroster mode, cold air bypasses around the PTC heater and the warmed air at the PTC heater is cooled down by the cold air around it. This results in insufficient heater performance. To eliminate this concern, the cold air around the PTC heater has been reduced and the control software of the heat pump control unit has been modified to increase the output temperature of the PTC heater.
Associated Products (1)Associated Documents - January 3, 2023•Document ID: 10230894Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 09-001-23
- Date Added:
- February 2, 2023
- Manufacturer:
- MAZDA
SummarySome vehicles may exhibit DTC U3000:04 (Telematics communication unit internal malfunction) stored after the connected service contract has been discontinued (only vehicles in which the customer opted out of CV services are affected - CSP04). This is caused by improper control software of telematics communication unit. To eliminate this concern, the control software of telematics communication unit has been modified.
Associated Products (14)Associated Documents - December 22, 2022•Document ID: 10228661Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC
- Mfr Comm. #:
- 04-006-22
- Date Added:
- January 5, 2023
- Manufacturer:
- MAZDA
SummarySome customers may complain about hearing a grinding noise and/or vibration occur when applying the brake. This is due to rust on the rear brake disc plate.
Associated Products (11)Associated Documents - December 14, 2022•Document ID: 10228650Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SA-004-22g
- Date Added:
- January 5, 2023
- Manufacturer:
- MAZDA
SummaryCustomers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.
Associated Products (17)Associated Documents - December 13, 2022•Document ID: 10228664Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 09-048-22
- Date Added:
- January 5, 2023
- Manufacturer:
- MAZDA
SummarySome vehicles may exhibit the following symptoms with DTC P05A0:00 (Active air shutter and the opening angle abnormality (sticking)) stored in memory. Symptom 1 [Mazda3 and CX-30]: The active air shutter is working, but DTC P05A0:00 is stored in memory. Cause 1: This is caused by improper control software of the PCM detecting the DTC immediately without performing the failsafe operation. When the active air shutter detects unusual torque, it is designed to repeat the open/close cycles up to three times as a failsafe to try to remove the object(s) which temporarily disturbed the movement. Symptom 2 [Mazda3, CX-30 and MX-30]: The active air shutter is frozen by snow and/or ice under freezing temperatures with DTC P05A0:00 stored in memory. Cause 2 [Mazda3 and CX-30]: When a temporary blocking of the active air shutter is expected to be caused by snow and/or ice and the intake air temperature is above the freezing point, DTC P05A0:00 may be unintentionally detected. [MX-30]: When a temporary blocking of the active air shutter is expected to be caused by snow and/or ice and the heater is turned on, DTC P05A0:00 may be unintentionally detected
Associated Products (6)Associated Documents - December 13, 2022•Document ID: 10228653Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SA-019-22c
- Date Added:
- January 5, 2023
- Manufacturer:
- MAZDA
SummaryMAZDA CONNECTED SERVICES Frequently Asked Questions (FAQ)
Associated Products (18)Associated Documents - December 13, 2022•Document ID: 10228652Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SA-017-22d
- Date Added:
- January 5, 2023
- Manufacturer:
- MAZDA
SummarySome customers may complain about any of the following: * Infotainment Center Display does not provide the Authorization Code during the MyMazda App Connected Vehicle enrollment. * Remote function(s) inoperative. - Engine Start / Stop - Door Lock / Unlock - Lights ON / OFF * MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ". Confirm the customer's phone and vehicle have good to strong reception during the concern as shown in the table below. * If the reception is weak, move the vehicle to a location where the reception is good to strong as shown in the table, then try to get the Authorization Code and/or operate the remote functions before proceeding to the Repair Procedure if there is still an issue. * If the reception is good to strong, proceed to the Repair Procedure
Associated Products (18)Associated Documents - December 7, 2022•Document ID: 10228651Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- SA-016-22a
- Date Added:
- January 5, 2023
- Manufacturer:
- MAZDA
SummaryThere are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method
Associated Products (64)2023 Mazda CX-302023 Mazda CX-52023 Mazda CX-502023 Mazda CX-92023 Mazda Mazda32023 Mazda MX-302023 Mazda MX-52022 Mazda CX-302022 Mazda CX-52022 Mazda CX-92022 Mazda Mazda32022 Mazda MX-302022 Mazda MX-52021 Mazda CX-32021 Mazda CX-302021 Mazda CX-52021 Mazda CX-92021 Mazda Mazda22021 Mazda Mazda32021 Mazda Mazda6+ 44 moreAssociated Documents - December 6, 2022•Document ID: 10228655Service Bulletin/Repair InstructionsVISIBILITY:GLASS, SIDE/REAR; EQUIPMENT
- Mfr Comm. #:
- SA-045-22a
- Date Added:
- January 5, 2023
- Manufacturer:
- MAZDA
SummaryThe purpose of this Service Alert is to remind dealers to keep the protective films on the piano black door garnishes attached until just before delivering the vehicle to the customer. The protective films are attached on new vehicles when shipped from the factory in order to avoid being scratched during transportation and while in dealer stock.
Associated Products (13)Associated Documents - November 22, 2022•Document ID: 10226856Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 09-019-22a
- Date Added:
- December 2, 2022
- Manufacturer:
- MAZDA
SummarySome customers may experience one or both of the following symptoms while locking and unlocking the doors works fine using the remote transmitter. - Symptom 1: The touch sensor of the front door outer handle does not lock the doors after rain and/or car washing, even though unlocking is possible. - Symptom 2: The touch sensor of the front door outer handle does not unlock the doors. - Cause 1 (for Symptom 1): Water may accumulate around the touch sensor in the outer handle, resulting in temporary lower sensitivity of the capacitive sensor. Also, if car wash foam gets inside the outer handle while washing the vehicle, the foam may disturb the touch sensor detection. Mazda is still working on a mass production change for this concern. - Cause 2 (for Symptom 2): Improper soldering in the production process may disturb the touch sensor detection. To eliminate this concern, the production process has been modified.
Associated Products (8)Associated Documents - November 21, 2022•Document ID: 10226892Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 09-046-22
- Date Added:
- December 2, 2022
- Manufacturer:
- MAZDA
SummarySome customers may experience that, with a specific operation, the touch sensor of front door outer handle does not lock and unlock the doors but the remote transmitter operates correctly. Description of the specific operations: - Specific Operation 1 [MX-30]: After using cabin preconditioning or hazard warning lights for approx.15 minutes. - Specific Operation 2 [MAZDA3 and CX-30]: After using hazard warning lights for approx. 15 minutes. - Specific Operation 3 [MAZDA3, CX-30 and MX-30]: When both touch sensors are touched at once. - Specific Operation 1 and 2 Cause: The touch sensor has been disabled to avoid the unintended locking/unlocking operation caused by rain. - Specific Operation 3 Cause: The control logic is not appropriate. To correct this issue, the control software of the LF control unit (LFU) has been modified.
Associated Products (8)Associated Documents - November 18, 2022•Document ID: 10226814Service Bulletin/Repair InstructionsSUSPENSION
- Mfr Comm. #:
- 02-004-22a
- Date Added:
- December 2, 2022
- Manufacturer:
- MAZDA
SummarySome customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
Associated Products (160)2023 Mazda CX-302023 Mazda CX-52023 Mazda CX-502023 Mazda CX-92023 Mazda Mazda32023 Mazda MX-52022 Mazda CX-302022 Mazda CX-52022 Mazda CX-92022 Mazda Mazda32022 Mazda MX-302022 Mazda MX-52021 Mazda CX-32021 Mazda CX-302021 Mazda CX-52021 Mazda CX-92021 Mazda Mazda32021 Mazda Mazda62021 Mazda MX-52020 Mazda CX-3+ 140 moreAssociated Documents - November 14, 2022•Document ID: 10226922Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SA-073-22
- Date Added:
- December 2, 2022
- Manufacturer:
- MAZDA
SummarySome customers may complain that the HVAC system's touch panel switches settings on it's own. When you receive a customer complaint regarding this concern, explain the following characteristics of the touch panel to the customer. The MX-30 heater control unit uses a capacitive touch screen which may determine that a switch has been pressed because of the close proximity of a hand, even though it has not been touched directly. No repair is necessary unless you confirm abnormal operation different from the description. NOTE: The heater control unitâÂÂs operation confirmation sound does not sound if there is another warning or confirmation sound of another system at the same time. Since the confirmation sound of the heater control unit is missing in this special case, some customers may feel that the heater control settings have switched by themselves.
Associated Products (1)Associated Documents - November 4, 2022•Document ID: 10226898Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 16-004-22a
- Date Added:
- December 2, 2022
- Manufacturer:
- MAZDA
SummarySome customers may complain that Mazda Connect does not start (blank screen) or that it takes a long time to restart/ reboot after starting the vehicle. This is caused by the initialization process with the CMU failing at startup due to a defective circuit board element. To eliminate this concern, the internal hardware (DRAM) of the CMU has been improved.
Associated Products (12)Associated Documents - November 2, 2022•Document ID: 10226916Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SA-064-22a
- Date Added:
- December 2, 2022
- Manufacturer:
- MAZDA
SummarySome customers may comlpain about an intermittent Beep sound (popping sound) every 1 ~ 2 minutes while driving. This may be cause by a software error in the navigation SD card.
Associated Products (13)Associated Documents - October 19, 2022•Document ID: 10225768Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SA-069-22
- Date Added:
- November 4, 2022
- Manufacturer:
- MAZDA
SummaryThis Service Information provides information on the AUXILIARY CHARGING SYSTEM for lead-acid battery and the POWER SAVING MODE for e-SKYACTIV.
Associated Products (1)Associated Documents - October 17, 2022•Document ID: 10225724Service Bulletin/Repair InstructionsSTRUCTURE
- Mfr Comm. #:
- SA-008-22a
- Date Added:
- November 4, 2022
- Manufacturer:
- MAZDA
SummarySome vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
Associated Products (132)2023 Mazda CX-302023 Mazda CX-52023 Mazda CX-502023 Mazda CX-92023 Mazda Mazda32023 Mazda MX-52022 Mazda CX-302022 Mazda CX-52022 Mazda CX-92022 Mazda Mazda32022 Mazda MX-302022 Mazda MX-52021 Mazda CX-32021 Mazda CX-302021 Mazda CX-52021 Mazda CX-92021 Mazda Mazda22021 Mazda Mazda32021 Mazda Mazda62021 Mazda MX-5+ 112 moreAssociated Documents - October 12, 2022•Document ID: 10225763Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SA-067-22
- Date Added:
- November 4, 2022
- Manufacturer:
- MAZDA
SummarySome customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: * The Forward Sensing Camera (FSC) cannot detect target objects due to one of the following: - The windshield is dirty - The FSC lens is foggy - There is low visibility due to rain, fog or snow - It is at night and there is not enough light - There is direct or reflected sunlight on the FSC - There is problem with the FSC * There is a problem with the AUTOHOLD control function. * There is a problem with the electric parking brake (EPB).
Associated Products (31)2023 Mazda CX-302023 Mazda CX-52023 Mazda CX-502023 Mazda CX-92023 Mazda Mazda32022 Mazda CX-302022 Mazda CX-52022 Mazda CX-92022 Mazda Mazda32022 Mazda MX-302021 Mazda CX-32021 Mazda CX-302021 Mazda CX-52021 Mazda CX-92021 Mazda Mazda32021 Mazda Mazda62020 Mazda CX-32020 Mazda CX-302020 Mazda CX-52020 Mazda CX-9+ 11 moreAssociated Documents - October 12, 2022•Document ID: 10225761Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SA-066-22
- Date Added:
- November 4, 2022
- Manufacturer:
- MAZDA
SummarySome vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: * C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles] * B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles built on or before March 2, 2019] * No DTC - Warning Message only [Gen 7 vehicles built after March 2, 2019] DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. * In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). * In other cases this DTC might be found without a related customer concern. NOTE: In most cases, no dealer visit is necessary.
Associated Products (55)2023 Mazda CX-302023 Mazda CX-52023 Mazda CX-502023 Mazda CX-92023 Mazda Mazda32023 Mazda MX-302023 Mazda MX-52022 Mazda CX-302022 Mazda CX-52022 Mazda CX-92022 Mazda Mazda32022 Mazda MX-302022 Mazda MX-52021 Mazda CX-32021 Mazda CX-302021 Mazda CX-52021 Mazda CX-92021 Mazda Mazda32021 Mazda Mazda62021 Mazda MX-5+ 35 moreAssociated Documents - October 10, 2022•Document ID: 10225730Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- SA-019-22b
- Date Added:
- November 4, 2022
- Manufacturer:
- MAZDA
SummaryMazda Connected Services Frequently Asked Questions (FAQs)
Associated Products (17)Associated Documents