Mazda CX-3 Service Bulletins (2021)

278 manufacturer communications on file.

• September 11, 2026•Document ID: 11037899

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  SA-041-26a

  Date Added:

  October 3, 2026

  Manufacturer:

  MAZDA

  Summary

  DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button

  Associated Products (139)

  2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-5+ 119 more
  Associated Documents

  • DownloadMC-11037899-0001.pdf↗
• August 10, 2026•Document ID: 11036688

  Service Bulletin/Repair Instructions
  ENGINE

  Mfr Comm. #:

  01-010-26

  Date Added:

  September 2, 2026

  Manufacturer:

  MAZDA

  Summary

  This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red text. 01-012/22 10/06/22 DESCRIPTION Some vehicles may exhibit accumulation of dried coolant (1) around the water pipe (2). This is caused by a gap between the housing and pipe due to a press fitting during the manufacturing process. The accumulated coolant is solidified and plugs the gap in high temperature environment and the seepage is stopped and does not progress. This is normal and does not require a part replacement, clean off the dried coolant from around the pipe with a wire brush. REPAIR PROCEDURE 1. Verify the customer concern. 2. If the above condition is experienced, remove the accumulated coolant around the pipe (1) with a wire brush etc. NOTE: Perform the procedure on the vehicle. No need to remove the water pipe and hoses.

  Associated Products (21)

  2023 Mazda CX-302022 Mazda CX-302022 Mazda CX-52021 Mazda CX-32021 Mazda CX-302021 Mazda CX-52021 Mazda Mazda32020 Mazda CX-32020 Mazda CX-302020 Mazda CX-52020 Mazda Mazda32019 Mazda CX-32019 Mazda CX-52019 Mazda Mazda32018 Mazda CX-32018 Mazda CX-52018 Mazda Mazda32017 Mazda CX-32017 Mazda CX-52017 Mazda Mazda3+ 1 more
  Associated Documents

  • DownloadMC-11036688-0001.pdf↗
• June 19, 2026•Document ID: 11034447

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM; ENGINE

  Mfr Comm. #:

  SA-041-26

  Date Added:

  July 3, 2026

  Manufacturer:

  MAZDA

  Summary

  This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. • IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.

  Associated Products (139)

  2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-5+ 119 more
  Associated Documents

  • DownloadMC-11034447-0001.pdf↗
• June 18, 2026•Document ID: 11034436

  Service Bulletin/Repair Instructions
  UNKNOWN OR OTHER; ENGINE; ELECTRICAL SYSTEM

  Mfr Comm. #:

  09-019-26

  Date Added:

  July 3, 2026

  Manufacturer:

  MAZDA

  Summary

  This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 09-012/21 12/13/21, 06/10/21 and 04/27/21 DESCRIPTION Some customers may experience all of following symptoms: The door lock/unlock operation will not work using the remote transmitter button. 1. The door lock/unlock operation will not work using the door lock/release touch sensor. 2. The engine will not start using the ignition switch. 3. The transmitter operates by itself. 4. The key battery drains faster than usual. 5. Symptoms 1-3: This may be caused when excess load is applied to the remote transmitter, deforming the electrical terminals and creating poor contact with the battery. To eliminate this concern, the structure in the remote transmitter has been modified to reduce the deformation of the electrical terminals. Symptom 4-5: This may be caused when excessive load is applied to the remote transmitter, creating a gap around the gasket where moisture enters and corrodes the circuit board which in turn drains the key battery faster than usual. To eliminate this concern, the thickness of the case wall on the gasket mounting surface has been increased and the bonding strength of the components has been improved to prevent deformation. REPAIR PROCEDURE • If the battery is bad or installed incorrectly, replace the battery and/or install it correctly. • If the remote power saving function is off and the battery is good and installed correctly, replace the defective remote transmitter with a modified one according to the instructions on MGSS (IMMOBILIZER SYSTEM-RELATED PARTS PROGRAMMING). NOTE: DO NOT replace other remote transmitter(s) for the vehicle if they not experiencing an issue.

  Associated Products (13)

  2021 Mazda CX-32021 Mazda CX-302021 Mazda CX-52021 Mazda CX-92021 Mazda Mazda32021 Mazda Mazda62020 Mazda CX-302020 Mazda CX-92020 Mazda Mazda32020 Mazda Mazda62020 Mazda MX-52019 Mazda Mazda32019 Mazda Mazda6
  Associated Documents

  • DownloadMC-11034436-0001.pdf↗
• June 17, 2026•Document ID: 11034439

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  SA-027-26a

  Date Added:

  July 3, 2026

  Manufacturer:

  MAZDA

  Summary

  This SA supersedes the previously issued bulletin(s) listed below. The changes are noted below in Red. SA-027/26 04/16/26 DESCRIPTION The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. REPAIR PROCEDURE 1. Perform appropriate repair to vehicle. If needed, use the Battery Diagnostics of the DCA-8000 to test the charging and starting systems by following the on-screen instructions for entering the appropriate information. Refer to the Mazda DCA-8000 Instruction Manual for more information.

  Associated Products (47)

  2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-5+ 27 more
  Associated Documents

  • DownloadMC-11034439-0001.pdf↗
• April 30, 2026•Document ID: 11032104

  Service Bulletin/Repair Instructions
  UNKNOWN OR OTHER; STRUCTURE:BODY

  Mfr Comm. #:

  SA-031-26

  Date Added:

  May 5, 2026

  Manufacturer:

  MAZDA

  Summary

  DESCRIPTION Some vehicles may require the replacement of a damaged VIN plate or vehicle certification label. To obtain a replacement VIN plate (bulkhead-mounted and visible through the lower-left area of the windshield), contact DAG (Dealer Assistance Group) using VIN Plate Request Form available on One Mazda. To obtain a replacement vehicle certification label (located on the B􀀀pillar or front door), contact your assigned DSM (District Service Manager) to place the order. If DSM contact information is not available, refer to the Dealer & Field Contact Directory.

  Associated Products (78)

  2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-5+ 58 more
  Associated Documents

  • DownloadMC-11032104-0001.pdf↗
• April 21, 2026•Document ID: 11032103

  Service Bulletin/Repair Instructions
  ENGINE; SERVICE BRAKES; UNKNOWN OR OTHER; POWER TRAIN

  Mfr Comm. #:

  SA-029-26

  Date Added:

  May 5, 2026

  Manufacturer:

  MAZDA

  Summary

  This Service Alert supersedes the previously issued SA listed below: The changes are noted in Red. SA-011/24 02/12/24, 06/06/24, 07/29/24 DESCRIPTION Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers. SCHEDULED MAINTENANCE Refer to the applicable Workshop Manual or Owner's Manual for vehicle -specific manufacturer scheduled maintenance. Workshop Manual - Refer to section 00-00 SCHEDULED MAINTENANCE. Owner's Manual - Refer to section 8 Maintenance and Care. b. Note: Please refer to the information below outlining the services not included in Mazda's Factory Scheduled Maintenance: IMPORTANT: Recommending fluid flushes when not necessary can lead to customer confusion and dissatisfaction. Fluid flushing for preventive maintenance purposes is strongly discouraged, unless otherwise specified in a published procedure (Owner’s Manual, Workshop Manual, Technical Service Bulletin, etc.).

  Associated Products (175)

  2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-5+ 155 more
  Associated Documents

  • DownloadMC-11032103-0001.pdf↗
• April 16, 2026•Document ID: 11032101

  Service Bulletin/Repair Instructions
  ENGINE

  Mfr Comm. #:

  SA-026-26

  Date Added:

  May 5, 2026

  Manufacturer:

  MAZDA

  Summary

  This Service Alert supersedes the previously issued M-Tip(s) listed below. The changes are noted in Red text. MT-002/19 09/30/19 and 12/19/19 DESCRIPTION If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage. Clean the intake manifold internally to remove any debris from old engine before installing the new replacement engine assembly. If the intake manifold cannot be properly cleaned internally, replace it.

  Associated Products (75)

  2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-5+ 55 more
  Associated Documents

  • DownloadMC-11032101-0001.pdf↗
• April 15, 2026•Document ID: 11032102

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  SA-027-26

  Date Added:

  May 5, 2026

  Manufacturer:

  MAZDA

  Summary

  This SA supersedes the previously issued bulletin(s) listed below. The changes are noted below in Red. SA-007/25 10/22/25, 06/02/25 and 02/03/25 DESCRIPTION The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps): CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a battery’s Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda DCA-8000, it will result in a false result and invalid Warranty Code from the tester. This will also result in unnecessary replacement of batteries. TEST PROCEDURE 1. Connect the charger clamps to the appropriate battery posts.

  Associated Products (47)

  2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-5+ 27 more
  Associated Documents

  • DownloadMC-11032102-0001.pdf↗
• April 11, 2026•Document ID: 11032019

  Service Bulletin/Repair Instructions
  FUEL/PROPULSION SYSTEM

  Mfr Comm. #:

  SA-023-26

  Date Added:

  May 4, 2026

  Manufacturer:

  MAZDA

  Summary

  This Service Alert supersedes the previously issued M-Tip(s) listed below. The changes are noted in Red text. MT-003/22 03/02/22 DESCRIPTION Some customers may complain about a tapping or knocking noise coming from the rear seat after fuel fill. The concern will likely occur if the fuel tank is overfilled (more fuel is added after the fuel pump nozzle shuts off automatically) or filled up normally in high ambient temperatures and the fuel expands. No repair is needed. Explain to the customer not to continue filling after nozzle shut off.

  Associated Products (21)

  2025 Mazda CX-52024 Mazda CX-52023 Mazda CX-52022 Mazda CX-52021 Mazda CX-32021 Mazda CX-52020 Mazda CX-32020 Mazda CX-52019 Mazda CX-32019 Mazda CX-52018 Mazda CX-32018 Mazda CX-52018 Mazda Mazda32017 Mazda CX-32017 Mazda CX-52017 Mazda Mazda32016 Mazda CX-32016 Mazda CX-52015 Mazda CX-52014 Mazda CX-5+ 1 more
  Associated Documents

  • DownloadMC-11032019-0001.pdf↗
• April 4, 2026•Document ID: 11032100

  Service Bulletin/Repair Instructions
  STRUCTURE:BODY; ELECTRICAL SYSTEM

  Mfr Comm. #:

  SA-021-26

  Date Added:

  May 5, 2026

  Manufacturer:

  MAZDA

  Summary

  This Service Alert supersedes the previously issued SAs and bulletin(s) listed below: The changes are noted below in red. SA-010/23 02/09/23 DESCRIPTION Some customers may experience one or more electrical malfunctions after a vehicle body repair. A newly painted fender stay (2) may be causing a poor front harness (1) ground connection. The front fender stay (2) newly painted surface at ground point (3), where attachment bolt (4) is seated, may create a poor front harness ground connection. NOTE: DO NOT paint ground point (3) attachment bolt (4) is seated. NEWLY INSTALLED FRONT FENDER STAY NOTE: CAUTION: If the bolt (4) contact area (3) is painted when the front fender stay (2) is newly replaced, it could cause a malfunction in the PCM. Before painting a newly replaced part, protect the bolt (4) contact area (3) with masking tape (5) as shown in the figure.

  Associated Products (36)

  2026 Mazda CX-502025 Mazda CX-52025 Mazda CX-502024 Mazda CX-52024 Mazda CX-502023 Mazda CX-52023 Mazda CX-502022 Mazda CX-52021 Mazda CX-32021 Mazda CX-52021 Mazda Mazda62020 Mazda CX-32020 Mazda CX-52020 Mazda Mazda62019 Mazda CX-32019 Mazda CX-52019 Mazda Mazda62018 Mazda CX-32018 Mazda CX-52018 Mazda Mazda3+ 16 more
  Associated Documents

  • DownloadMC-11032100-0001.pdf↗
• March 11, 2026•Document ID: 11030636

  Service Bulletin/Repair Instructions
  ENGINE

  Mfr Comm. #:

  SA-014-26

  Date Added:

  April 2, 2026

  Manufacturer:

  MAZDA

  Summary

  This Service Alert supersedes the previously issued SA(s) and TSB(s) listed below: The changes are noted in Red. SA-035/24 05/31/24 DESCRIPTION There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not. A mechanical seal (A) is used for the water pump. This mechanical seal can seal coolant (B) by sliding a mating ring (C) against a seal ring (D). When the sliding surface temperature of the mechanical seal is more than 248 °F (120 °C) while driving, a small amount of steam (E) is leaked and bleeds through the bleeding hole (F). After drying, the steam leaves a green coolant deposit near the water pump bleed hole (F). This is a normal condition and does not require water pump replacement. The water pump should only be replaced if there is an accumulation of crystallized coolant near the bleed hole. When you encounter a water pump with coolant seepage marks, decide to replace it or not based on the following criteria using sample photos. NOTE: During the initial period of use*, the sliding surfaces of the seals may not yet be fully settled, which can temporarily increase the amount of leakage. Continued use will allow the surfaces to settle, reducing the leakage. Replacing parts that are already settled with new ones will increase the leakage again until the new parts become conditioned. Therefore, replacement should be avoided in this initial period of use. *As a guideline, this applies to vehicles with less than 1,860 miles (3000 km) of mileage.

  Associated Products (55)

  2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-52023 Mazda CX-302023 Mazda CX-5+ 35 more
  Associated Documents

  • DownloadMC-11030636-0001.pdf↗
• March 5, 2026•Document ID: 11030701

  Warranty Program/Extension
  ENGINE

  Mfr Comm. #:

  SSPD8 Repair d

  Date Added:

  April 4, 2026

  Manufacturer:

  MAZDA

  Summary

  Subject: TSB 01-001/26 Warranty and Parts Kit Update INCLUDES: Warranty Extension Program - Special Service Program (SSP) D8 Check Engine Light ON with DTC P0126:00, 2018-2025 CX-5, 2019-2023 Mazda3, 2019-2022 CX-3, 2018-2021 Mazda6, 2020-2023 CX-30 Dear Mazda Dealer Colleagues, Mazda Motor Corporation has made a change regarding related parts to TSB 01-001/26 which also impacts Warranty Extension Special Service Program (SSPD8). Parts Ordering and Warranty Claims: Effective March 5, 2026 only the related parts kit PYY2-15-SAY can be ordered and claimed for any repair. The two separate parts PYFB-15-169 and PE13-15-296 can no longer be claimed with repaired dates of March 5, 2026 and later. There is no change to the main part, the Plug PYY3-15-SA1. We have updated the TSB 01-001/26 and SSPD8 Repair Procedure and Parts & Warranty Information on Mazda Global Service Support (MGSS) to reflect this change.

  Associated Products (24)

  2025 Mazda CX-52024 Mazda CX-52023 Mazda CX-302023 Mazda CX-52023 Mazda Mazda32022 Mazda CX-302022 Mazda CX-52022 Mazda Mazda32021 Mazda CX-32021 Mazda CX-302021 Mazda CX-52021 Mazda Mazda32021 Mazda Mazda62020 Mazda CX-32020 Mazda CX-302020 Mazda CX-52020 Mazda Mazda32020 Mazda Mazda62019 Mazda CX-32019 Mazda CX-5+ 4 more
  Associated Documents

  • DownloadMC-11030701-0001.pdf↗
• March 5, 2026•Document ID: 11030700

  Warranty Program/Extension
  ENGINE

  Mfr Comm. #:

  SSPD8 Dlr Ltr a

  Date Added:

  April 4, 2026

  Manufacturer:

  MAZDA

  Summary

  Subject: TSB 01-001/26 Warranty and Parts Kit Update INCLUDES: Warranty Extension Program - Special Service Program (SSP) D8 Check Engine Light ON with DTC P0126:00, 2018-2025 CX-5, 2019-2023 Mazda3, 2019-2022 CX-3, 2018-2021 Mazda6, 2020-2023 CX-30 Dear Mazda Dealer Colleagues, Mazda Motor Corporation has made a change regarding related parts to TSB 01-001/26 which also impacts Warranty Extension Special Service Program (SSPD8). Parts Ordering and Warranty Claims: Effective March 5, 2026 only the related parts kit PYY2-15-SAY can be ordered and claimed for any repair. The two separate parts PYFB-15-169 and PE13-15-296 can no longer be claimed with repaired dates of March 5, 2026 and later. There is no change to the main part, the Plug PYY3-15-SA1. We have updated the TSB 01-001/26 and SSPD8 Repair Procedure and Parts & Warranty Information on Mazda Global Service Support (MGSS) to reflect this change.

  Associated Products (24)

  2025 Mazda CX-52024 Mazda CX-52023 Mazda CX-302023 Mazda CX-52023 Mazda Mazda32022 Mazda CX-302022 Mazda CX-52022 Mazda Mazda32021 Mazda CX-32021 Mazda CX-302021 Mazda CX-52021 Mazda Mazda32021 Mazda Mazda62020 Mazda CX-32020 Mazda CX-302020 Mazda CX-52020 Mazda Mazda32020 Mazda Mazda62019 Mazda CX-32019 Mazda CX-5+ 4 more
  Associated Documents

  • DownloadMC-11030700-0001.pdf↗
• March 4, 2026•Document ID: 11030598

  Service Bulletin/Repair Instructions
  UNKNOWN OR OTHER; ENGINE

  Mfr Comm. #:

  01-001-26b

  Date Added:

  April 2, 2026

  Manufacturer:

  MAZDA

  Summary

  Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. Vehicles with SKYACTIV-G 2.5T are not applicable to this service information. DTC P0126:00 is not required to be present to perform this repair. If the vehicle has not previously had the repair specified in this TSB and is exhibiting any of the listed symptoms, proceed with the repair procedure outlined in this bulletin. If DTC P2B61:00 (Coolant Control Valve Circuit Range/Performance) is present along with DTC P0126:00, this TSB does not apply. Diagnose the symptom and/or stored DTCs according to the procedures in MGSS. If only DTC P0126:00 is present and this TSB has already been completed previously, this bulletin does not apply, diagnose the symptom and/or stored DTCs according to the procedures in MGSS. This concern may be caused if the coolant control valve fail-safe thermostat opens at a temperature lower than the normal temperature due to a deformation of the thermostat diaphragm. To eliminate the concern, the water flow control valve specification has been modified. Affected vehicles will require PCM reprogramming with the Mazda Modular Diagnostic System (M-MDS), using either a) Mazda Diagnostic and Repair Software (MDARS) or b) Mazda Integrated Diagnostic System (IDS) 140.04 or later software.

  Associated Products (24)

  2025 Mazda CX-52024 Mazda CX-52023 Mazda CX-302023 Mazda CX-52023 Mazda Mazda32022 Mazda CX-302022 Mazda CX-52022 Mazda Mazda32021 Mazda CX-32021 Mazda CX-302021 Mazda CX-52021 Mazda Mazda32021 Mazda Mazda62020 Mazda CX-32020 Mazda CX-302020 Mazda CX-52020 Mazda Mazda32020 Mazda Mazda62019 Mazda CX-32019 Mazda CX-5+ 4 more
  Associated Documents

  • DownloadMC-11030598-0001.pdf↗
• February 11, 2026•Document ID: 11029534

  Other
  ENGINE

  Mfr Comm. #:

  PF-26-01

  Date Added:

  March 4, 2026

  Manufacturer:

  MAZDA

  Summary

  The coolant control valve updated part is now available and supersedes PYFD-15-16ZA. As a result, PYFD-15-16ZA is no longer available. PW5S-15-16Z is supplied with a dummy plug pre-installed. Critical Installation Requirement: When replacing PW5S-15-16Z, the Powertrain Control Module (PCM) must also be updated to the latest software version. Failure to perform the PCM update may result in drivability concerns or diagnostic trouble codes.

  Associated Products (24)

  2025 Mazda CX-52024 Mazda CX-52023 Mazda CX-302023 Mazda CX-52023 Mazda Mazda32022 Mazda CX-302022 Mazda CX-52022 Mazda Mazda32021 Mazda CX-32021 Mazda CX-302021 Mazda CX-52021 Mazda Mazda32021 Mazda Mazda62020 Mazda CX-32020 Mazda CX-302020 Mazda CX-52020 Mazda Mazda32020 Mazda Mazda62019 Mazda CX-32019 Mazda CX-5+ 4 more
  Associated Documents

  • DownloadMC-11029534-0001.pdf↗
• February 6, 2026•Document ID: 11029542

  Warranty Program/Extension
  ENGINE

  Mfr Comm. #:

  SSPD8 Repair c

  Date Added:

  March 4, 2026

  Manufacturer:

  MAZDA

  Summary

  SSPD8 - Check Engine Light ON with DTC P0126:00 - WARRANTY EXTENSION For certain 2018-2025MY CX-5, 2019-2023MY Mazda3, 2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a “Software Update” record for the PCM when using MDARS or IDS. • MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. • IDS – Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealer’s expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.

  Associated Products (24)

  2025 Mazda CX-52024 Mazda CX-52023 Mazda CX-302023 Mazda CX-52023 Mazda Mazda32022 Mazda CX-302022 Mazda CX-52022 Mazda Mazda32021 Mazda CX-32021 Mazda CX-302021 Mazda CX-52021 Mazda Mazda32021 Mazda Mazda62020 Mazda CX-32020 Mazda CX-302020 Mazda CX-52020 Mazda Mazda32020 Mazda Mazda62019 Mazda CX-32019 Mazda CX-5+ 4 more
  Associated Documents

  • DownloadMC-11029542-0001.pdf↗
• January 31, 2026•Document ID: 11028092

  Service Bulletin/Repair Instructions
  ENGINE

  Mfr Comm. #:

  01-001-26a

  Date Added:

  February 3, 2026

  Manufacturer:

  MAZDA

  Summary

  Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. • Engine temperature gauge fluctuates. • Low coolant temperature indicator (blue) light stays on longer or turns on while driving. • Poor heater performance, especially at idle. • This concern may be caused if the coolant control valve fail-safe thermostat opens at a temperature lower than the normal temperature due to a deformation of the thermostat diaphragm. To eliminate the concern, the water flow control valve specification has been modified.

  Associated Products (24)

  2025 Mazda CX-52024 Mazda CX-52023 Mazda CX-302023 Mazda CX-52023 Mazda Mazda32022 Mazda CX-302022 Mazda CX-52022 Mazda Mazda32021 Mazda CX-32021 Mazda CX-302021 Mazda CX-52021 Mazda Mazda32021 Mazda Mazda62020 Mazda CX-32020 Mazda CX-302020 Mazda CX-52020 Mazda Mazda32020 Mazda Mazda62019 Mazda CX-32019 Mazda CX-5+ 4 more
  Associated Documents

  • DownloadMC-11028092-0001.pdf↗
• January 30, 2026•Document ID: 11028143

  Warranty Program/Extension
  ENGINE

  Mfr Comm. #:

  SSPD8 Repair b

  Date Added:

  February 3, 2026

  Manufacturer:

  MAZDA

  Summary

  SSPD8 - Check Engine Light ON with DTC P0126:00 - WARRANTY EXTENSION For certain 2018-2025MY CX-5, 2019-2023MY Mazda3, 2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a “Software Update” record for the PCM when using MDARS or IDS. • MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. • IDS – Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealer’s expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.

  Associated Products (24)

  2025 Mazda CX-52024 Mazda CX-52023 Mazda CX-302023 Mazda CX-52023 Mazda Mazda32022 Mazda CX-302022 Mazda CX-52022 Mazda Mazda32021 Mazda CX-32021 Mazda CX-302021 Mazda CX-52021 Mazda Mazda32021 Mazda Mazda62020 Mazda CX-32020 Mazda CX-302020 Mazda CX-52020 Mazda Mazda32020 Mazda Mazda62019 Mazda CX-32019 Mazda CX-5+ 4 more
  Associated Documents

  • DownloadMC-11028143-0001.pdf↗
• January 30, 2026•Document ID: 11028142

  Warranty Program/Extension
  ENGINE

  Mfr Comm. #:

  SSPD8 Parts and Warr a

  Date Added:

  February 3, 2026

  Manufacturer:

  MAZDA

  Summary

  SSPD8 - Check Engine Light ON with DTC P0126:00 - WARRANTY EXTENSION For certain 2018-2025MY CX-5, 2019-2023MY Mazda3, 2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a “Software Update” record for the PCM when using MDARS or IDS. • MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. • IDS – Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealer’s expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.

  Associated Products (26)

  2025 Mazda CX-52025 Mazda Mazda32024 Mazda CX-52024 Mazda Mazda32023 Mazda CX-302023 Mazda CX-52023 Mazda Mazda32022 Mazda CX-302022 Mazda CX-52022 Mazda Mazda32021 Mazda CX-32021 Mazda CX-302021 Mazda CX-52021 Mazda Mazda32021 Mazda Mazda62020 Mazda CX-32020 Mazda CX-302020 Mazda CX-52020 Mazda Mazda32020 Mazda Mazda6+ 6 more
  Associated Documents

  • DownloadMC-11028142-0001.pdf↗