Mazda CX-3 Service Bulletins
807 manufacturer communications on file.
- February 22, 2018•Document ID: 10136368Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- 09-001-18-3387a
- Date Added:
- May 7, 2018
- Manufacturer:
- MAZDA
SummarySome customers may experience the MAZDA CONNECT rebooting or the screen turning black during extremely cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. This is caused by some SD cards for the MAZDA CONNECT navigation system being manufactured with improper hardware, resulting in a data reading error during extremely cold temperatures. To correct the concern, the SD card hardware has been changed.
Associated Products (17)Associated Documents - February 22, 2018•Document ID: 10136325Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM
- Mfr Comm. #:
- 01-005-18-3415
- Date Added:
- May 7, 2018
- Manufacturer:
- MAZDA
SummarySome vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded P0524:00 - Engine oil pressure too low This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine light on, but rough idle will not be produced until a later time.
Associated Products (20)2018 Mazda CX-32018 Mazda Mazda32018 Mazda Mazda62017 Mazda CX-32017 Mazda CX-52017 Mazda Mazda32017 Mazda Mazda62016 Mazda CX-32016 Mazda CX-52016 Mazda Mazda32016 Mazda Mazda62015 Mazda CX-52015 Mazda Mazda32015 Mazda Mazda62014 Mazda CX-52014 Mazda Mazda32014 Mazda Mazda62013 Mazda CX-52013 Mazda Mazda32012 Mazda Mazda3Associated Documents - February 20, 2018•Document ID: 10134920Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- SA-008-18
- Date Added:
- April 23, 2018
- Manufacturer:
- MAZDA
SummarySome customers may complain about the MAZDA CONNECT center display cracking (spider cracking). The cracks are internal and cannot be felt by touch. This may be caused by a faulty center display.
Associated Products (18)Associated Documents - February 16, 2018•Document ID: 10134925Service Bulletin/Repair InstructionsAIR BAGS; EQUIPMENT
- Mfr Comm. #:
- MT-003-18
- Date Added:
- April 23, 2018
- Manufacturer:
- MAZDA
SummaryThe Workshop Manual has two-different airbag procedures, one for Standard Deployment and one for Two-Step Deployment. Standard Deployment is for Mexico spec vehicles and Two-Step Deployment is for US and Canadian spec vehicles.
Associated Products (94)2018 Mazda CX-32018 Mazda CX-52018 Mazda CX-92018 Mazda Mazda32018 Mazda Mazda62018 Mazda MX-52017 Mazda CX-32017 Mazda CX-52017 Mazda CX-92017 Mazda Mazda32017 Mazda Mazda62017 Mazda MX-52016 Mazda CX-32016 Mazda CX-52016 Mazda CX-92016 Mazda Mazda32016 Mazda Mazda62016 Mazda MX-52015 Mazda CX-52015 Mazda CX-9+ 74 moreAssociated Documents - February 16, 2018•Document ID: 10134921Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
- Mfr Comm. #:
- SA-009-18
- Date Added:
- April 23, 2018
- Manufacturer:
- MAZDA
SummaryThe navigation SD Card VIN-locks to a vehicle in the following conditions: 1. Vehicle odometer under 62 miles ? VIN-lock occurs with key ON for 3 minutes or longer. 2. Vehicle odometer over 62 miles ? VIN-lock occurs at key ON. Navigation SD Card Map Update Note: Mazda Toolbox navigation SD card map update can only be performed on a navigation SD card that is VIN-locked. See VIN-lock procecure below.
Associated Products (20)2018 Mazda CX-32018 Mazda CX-52018 Mazda CX-92018 Mazda Mazda32018 Mazda Mazda62018 Mazda MX-52017 Mazda CX-32017 Mazda CX-52017 Mazda CX-92017 Mazda Mazda32017 Mazda Mazda62017 Mazda MX-52016 Mazda CX-32016 Mazda CX-52016 Mazda CX-92016 Mazda Mazda32016 Mazda Mazda62016 Mazda MX-52015 Mazda Mazda32014 Mazda Mazda3Associated Documents - February 14, 2018•Document ID: 10136370Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); ELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- 09-007-18-3422
- Date Added:
- May 7, 2018
- Manufacturer:
- MAZDA
SummarySome customers may experience a navigation system screen that shows the wrong location. This concern is due to poor reception of the GPS signals. To eliminate this concern, the CMU hardware has been modified.
Associated Products (15)Associated Documents - February 9, 2018•Document ID: 10134924Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- MT-002-18
- Date Added:
- April 23, 2018
- Manufacturer:
- MAZDA
SummarySome customers may complain about improper operation of the MAZDA CONNECT system when streaming music with audio source aha/Pandora/Stitcher/Bluetooth® and the same device is also connected to the USB port for charging. The concerns may include: Blank Screen and/or No Audio Sound, Phone will not charge, Blank Screen and/or No Audio Sound
Associated Products (20)2018 Mazda CX-32018 Mazda CX-52018 Mazda CX-92018 Mazda Mazda32018 Mazda Mazda62018 Mazda MX-52017 Mazda CX-32017 Mazda CX-52017 Mazda CX-92017 Mazda Mazda32017 Mazda Mazda62017 Mazda MX-52016 Mazda CX-32016 Mazda CX-52016 Mazda CX-92016 Mazda Mazda32016 Mazda Mazda62016 Mazda MX-52015 Mazda Mazda32014 Mazda Mazda3Associated Documents - February 8, 2018•Document ID: 10134917Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.
- Mfr Comm. #:
- SA-005-18
- Date Added:
- April 23, 2018
- Manufacturer:
- MAZDA
SummarySome customers may complain about SIRIUSXM satellite radio does not show album art, artist biographies or station logos in the center display. This is a normal condition.
Associated Products (20)2018 Mazda CX-32018 Mazda CX-52018 Mazda CX-92018 Mazda Mazda32018 Mazda Mazda62018 Mazda MX-52017 Mazda CX-32017 Mazda CX-52017 Mazda CX-92017 Mazda Mazda32017 Mazda Mazda62017 Mazda MX-52016 Mazda CX-32016 Mazda CX-52016 Mazda CX-92016 Mazda Mazda32016 Mazda Mazda62016 Mazda MX-52015 Mazda Mazda32014 Mazda Mazda3Associated Documents - January 17, 2018•Document ID: 10129570Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- 07-001-18-3274b
- Date Added:
- March 5, 2018
- Manufacturer:
- MAZDA
SummarySome customers may complain about warm air from the climate control vents when the air conditioner isON. This may be caused by condenser corrosion, causing a refrigerant leak.The manufacturer of the condenser has been changed and the configuration of the condenser tube hasbeen improved.
Associated Products (2)Associated Documents - January 16, 2018•Document ID: 10129569Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- 09-003-18-3405a
- Date Added:
- March 5, 2018
- Manufacturer:
- MAZDA
SummarySome customers may complain that the Voice Recognition system does not recognize "Address" or "New Destination" navigation voice commands. This may be caused by faulty navigation SD card software. The SD card has been updated to eliminate this concern.
Associated Products (7)Associated Documents - January 10, 2018•Document ID: 10129567Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- 09-003-18-3405
- Date Added:
- March 5, 2018
- Manufacturer:
- MAZDA
SummarySome customers may complain that the Voice Recognition system does not recognize "Address" or "NewDestination" navigation voice commands. This may be caused by faulty navigation SD card software. TheSD card has been updated to eliminate this concern.
Associated Products (6)Associated Documents - January 9, 2018•Document ID: 10129566Service Bulletin/Repair InstructionsELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
- Mfr Comm. #:
- 09-002-18-3410
- Date Added:
- March 5, 2018
- Manufacturer:
- MAZDA
SummaryAfter the installation of a new instrument cluster, the message "Fctry" or "Factory" is displayed instead ofthe odometer. This concern may also occur when a room fuse is installed in a new vehicle.Some new instrument clusters are in the factory mode setting. Factory mode cancellation is required.NOTE: The concern is applicable to Calsonic Kansei instrument clusters. Not all trim levels are affected.CX-3 shown:Vehicles having this concern should have their vehicle repaired using the following procedure.
Associated Products (16)Associated Documents - January 8, 2018•Document ID: 10153226Service Bulletin/Repair InstructionsWHEELS
- Mfr Comm. #:
- RF-18-02R1
- Date Added:
- February 19, 2019
- Manufacturer:
- MAZDA
SummaryAs of May 1, 2018, Japan produced vehicles use 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing new lug nuts or the accessory Wheel Lock Set, make sure to use the appropriate part number for the vehicle you are working on. NOTE: The Mazda3 produced in Mexico is not affected.Use the GEPC or the Mazda Accessory web site [MXConnect (dealers.mazdausa.com)] to look up the correct part number for the vehicle you are working on.
Associated Products (9)Associated Documents - January 8, 2018•Document ID: 10129565Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- 09-001-18-3387
- Date Added:
- March 5, 2018
- Manufacturer:
- MAZDA
SummarySome customers may experience the MAZDA CONNECT rebooting or the screen turning black during coldtemperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interiorwarms up. This is caused by some for the MAZDA CONNECT navigation system SD cards beingmanufactured with improper hardware, resulting in a data reading error during cold temperatures. To correctthe concern, the SD card hardware has been changed.
Associated Products (15)Associated Documents - January 5, 2018•Document ID: 10129564Service Bulletin/Repair InstructionsSUSPENSION:FRONT:SHOCK ABSORBER
- Mfr Comm. #:
- 02-002-18-3300d
- Date Added:
- March 5, 2018
- Manufacturer:
- MAZDA
SummarySome vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving onrough roads and/or when turning the steering wheel while the vehicle is stopped.The noise may be due to: Upper front strut bearing (A) damage. (CX-5 and Mazda6) Squeak type noise between the front strut bearing and coil spring. (CX-3, CX-5 and Mazda6) The bump stopper (C) may be contacting the strut bearing when the front shock absorber is compressed, causing a popping noise. (Mazda6 only) The front lower arm bushing (D) is making a creak type noise in wet road conditions. (CX-5 and Mazda6).Front Shock Absorber Front Lower Arm To eliminate the noise, the following mass-production changes have been made: 1. The material and production method of the front strut bearing (A) has been changed. (CX-5 and Mazda6) 2. A protector has been installed onto the coil spring. (CX-5 and Mazda6) 3. The shape of the bump stopper (C) will be modified in the future. (Mazda6 only) 4. The shape of the coil spring has been changed. (CX-3 only) 5. Friction of the lower arm bushing has been reduced by adding a dry coating. (CX-5 and Mazda6). NOTE: The piston rod nut (B) requires replacement.
Associated Products (10)Associated Documents - January 4, 2018•Document ID: 10129353Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
- Mfr Comm. #:
- SA-001-18
- Date Added:
- February 26, 2018
- Manufacturer:
- MAZDA
SummaryThe MAZDA MOBILE START (MMS) is currently experiencing a system disruption. User web portal and Call center web portal functions are affected. Mazda is working on this issue and will notify dealers when MMS service has been fully restored. We apologize for any inconvenience this may have caused you or your dealer.
Associated Products (17)Associated Documents - January 2, 2018•Document ID: 10129354Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- MT-001-18
- Date Added:
- February 26, 2018
- Manufacturer:
- MAZDA
SummaryWhen installing a navigation SD card, the center display may show error message "Invalid SD Card". This may be caused by: The navigation SD card lock tab is locked.The navigation SD card has a VIN mismatch due to SD card swapping.The navigation SD card has a malfunction.
Associated Products (23)2018 Mazda CX-32018 Mazda CX-52018 Mazda CX-92018 Mazda Mazda22018 Mazda Mazda32018 Mazda Mazda62018 Mazda MX-52017 Mazda CX-32017 Mazda CX-52017 Mazda CX-92017 Mazda Mazda22017 Mazda Mazda32017 Mazda Mazda62017 Mazda MX-52016 Mazda CX-32016 Mazda CX-52016 Mazda CX-92016 Mazda Mazda22016 Mazda Mazda32016 Mazda Mazda6+ 3 moreAssociated Documents - December 22, 2017•Document ID: 10129351Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 15-006-17-3388a
- Date Added:
- February 26, 2018
- Manufacturer:
- MAZDA
SummarySome customers may complain about one or more warning lights ON when they start the vehicle during hot weather. The following DTCs are stored in memory: U3000:98 - Forward sensing camera (FSC) stops functioning due to temporary high temperature. U3000:04 - Forward sensing camera (FSC) internal malfunction. The combination of warning lights mentioned by the customer may include: SCBS/SBS, LAS/LDWS, HBC, Master Warning LightInstrument Cluster Multi-Information Display (if equipped) warning messages may include: Forward Smart City Brake Support Malfunction, Smart Brake System Malfunction, Front Camera Sensor System Malfunction, MAZDA CONNECT center display warning messages may include: High Beam Control [HBC] / Lane-keep Assist System [LAS] Malfunction. Have the vehicle checked by a dealer if this indicator stays on. Smart City Brake Support [SCBS] Malfunction. Have the vehicle checked by a dealer immediately. Note: The center display Warning Messages are only displayed when the customer selects Applications>Vehicle Status Monitor>Warning Guidance>Warnings. This condition may be caused by FSC control logic that is too sensitive. When the FSC detects DTCU3000:98 during high temperature, it stops the internal communication and stores DTC U3000:04. DTC U3000:04 will not clear and SCBS/SBS, LAS/LDWS, and/or HBC functions will not resume until the ignition switch has been turned OFF, even if the temperature of the FSC cools. Before FSC Reprogramming: The warning lights/messages will be displayed until the FSC cools and the ignition is turned OFF, then back ON. Instrument Instrument Cluster Warning Lights and MAZDA CONNECT Warning Messages Cluster Warning Messages Warning Lights (With Multi-Information Display) (Without Multi-Information Display), Note: These Warning Messages are displayed when the customer selects Applications>Vehicle Status Monitor>Warning Guidance>Warnings.
Associated Products (5)Associated Documents - December 22, 2017•Document ID: 10129349Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 00-003-17-3406
- Date Added:
- February 26, 2018
- Manufacturer:
- MAZDA
SummaryIn support of the new Mazda MX-5 and CX-3, Mazda will make available for loan on a "as-needed" basis, aSpecial Service Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. The (BSM) radar aiming is performed whenever the (BSM) control module, the (BSM) bracket or the rear bumper is replaced. The tool is available for loan on Mazda e-Store.
Associated Products (6)Associated Documents - December 18, 2017•Document ID: 10185794Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; AIR BAGS
- Mfr Comm. #:
- 01-001-17
- Date Added:
- January 25, 2021
- Manufacturer:
- MAZDA
SummarySome vehicles may experience the CHECK ENGINE LIGHT OIN with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A removed * P2610 Instrument cluster internal engine off timer performance problem * P2507 PCM battery voltage low input.
Associated Products (12)Associated Documents