Ford Transit Service Bulletins
265 manufacturer communications on file.
- March 31, 2021•Document ID: 10189867Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- TSB 21-2044
- Date Added:
- April 5, 2021
- Manufacturer:
- FORD
SummarySome 2020-2021 Transit vehicles equipped with a gas engine may exhibit a harsh engagement into drive with or without an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0772 and/or P2704 in the powertrain control module (PCM). This may be due to sticking valves in the main control valve body. Most vehicles will improve and no longer exhibit the condition after the first 8,000 km (5,000 mi) of driving. To correct the condition, follow the Service Procedure steps to perform the transmission accelerated main control break-in routine and/or overhaul the main control valve body.
Associated Products (1)Associated Documents - March 25, 2021•Document ID: 10189581Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SSM 49690
- Date Added:
- March 31, 2021
- Manufacturer:
- FORD
SummaryFor 2018-2021 EcoSport/Expedition/Navigator, 2019-2021 Ranger/Transit Connect, 2020-2021 Escape/Explorer/SuperDuty/Transit/Aviator/Corsair, 2021 Bronco Sport/F-150/Mustang/Mach-E the Workshop Manual (WSM) diagnostics may direct to replace a module on vehicles that use Ford Diagnosis and Repair System (FDRS). First, an FDRS session must be created on the vehicle prior to removing the faulted module. Once the session is started, run the Programmable Module Installation and replace the module only when instructed by FDRS. Installing a new module prior to starting a scan tool session may result in incomplete module configuration with DTCs U2100, U2101 and/or U2200. Once a session has been started, continue to follow normal WSM procedures to repair the vehicle.
Associated Products (13)Associated Documents - March 15, 2021•Document ID: 10189565Service Bulletin/Repair InstructionsSTRUCTURE
- Mfr Comm. #:
- SSM 49665
- Date Added:
- March 31, 2021
- Manufacturer:
- FORD
SummarySome 2015-2021 Transit vehicles may experience difficulty opening and/or closing the manual sliding door that will require sliding door adjustment. When performing the sliding door adjustment procedure in Workshop Manual (WSM), Section 501-03, use the following updated torque specs. Step 12 = 70 Nm (52 ft-lb). Step 27 = 40 Nm (30 ft-lb). In step 18, apply Motorcraft Threadlock 262 (TA-26) to the nut before torqueing. The WSM is in the process of being updated to include these revisions.
Associated Products (1)Associated Documents - March 10, 2021•Document ID: 10189781Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- TSB 21-2064
- Date Added:
- April 3, 2021
- Manufacturer:
- FORD
SummarySome 2015-2021 Transit vehicles equipped with rear wheel drive (RWD), single rear wheel (SRW), and a U-joint at the transmission flange and rear driveshaft may experience a boom/hum/moan noise or vibration from the rear while driving. This noise or vibration is most prevalent at highway speeds (112-121 km/h 7075 mph for 4.10 axle ratio, 121-128 km/h 75-80 mph for 3.73 axle ratio, and 136-145 km/h 85-90 mph for 3.31 axle ratio) and may also be present to a lesser degree at roughly half of those speeds. This may be due to a 2nd order driveline frequency transmitted through the rear drive shaft, rear axle and into the body through the leaf springs. To correct the condition, follow the Service Procedure to install a driveshaft torsional damper.
Associated Products (1)Associated Documents - January 29, 2021•Document ID: 10186651Service Bulletin/Repair InstructionsPOWER TRAIN; ELECTRICAL SYSTEM
- Mfr Comm. #:
- SSM 49510
- Date Added:
- February 4, 2021
- Manufacturer:
- FORD
SummarySome 2020-2021 Transit vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with all of the following diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM): P2804, P2803, P0713, P0710, P0709, and P0708. This article only applies if all of these DTCs are present. Prior to any diagnosis, inspect connectors C1551, C1280, C1281, and C1520 for partial connections, damage, or pushed out pins and repair as necessary. If a fault is not identified during the inspections of the connectors, continue diagnosis using the appropriate WSM Sections.
Associated Products (1)Associated Documents