Ford Bronco Complaints

938 consumer complaints on file.

#11746338June 24, 2026
STRUCTURE:BODY
Bronco hard top is beginning to warp really bad and delaminate. Classic problem happening with there and ford still refuses to come up with a real solution. Every day the warping gets worse and I’m just waiting for it to get bad enough so I can take it in and ford actually do something about it. The warping and delaminating also impacts the seals of the hardtop panels on the car. The top also rattles really bad. Absolutely crazy for an expensive car. It’s very obvious that climate and humidity have the largest impact on this issue and STILL they do nothing about it.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11746140June 24, 2026
LANE DEPARTURE: BLIND SPOT DETECTION
Camera and sensor on driver side does not indicate movement/stops working. This results in the Blindspot detection not working or any cross traffic alerts or object detection, which can lead to an accident. occurs intermittently and car does not issue a warning that the system is not working or down. Also causing an issue when backing up
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11746025June 23, 2026
BACK OVER PREVENTION
The contact owns a 2024 Ford Bronco. The contact stated that on several occasions, the APIM overheated, and the rearview camera was inoperable. The VIN was not included in NHTSA Campaign Number: 26V124000 (Back Over Prevention). Additionally, the power windows and AC were inoperable due to the failure. The contact stated that the vehicle stalled due to the APIM overheating. The dealer was contacted, and a repair of the vehicle was pending. The manufacturer was not made aware of the failure. The failure mileage was unknown.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11745907June 23, 2026
ELECTRICAL SYSTEM
On June 22, 2026, my 2025 Ford Bronco caught fire while parked outside a store. The vehicle had been parked for approximately five minutes when the fire began. There were no warning lights, alerts, unusual odors, or other indications of a problem before the incident. The fire and heavy smoke appeared to originate from the center console area near the gear shifter. The flames quickly spread throughout the driver’s side, center console, front passenger area, and the rest of the vehicle’s interior. The entire interior sustained severe fire and heat damage and was substantially melted. The responding fire department advised that temperatures inside the vehicle were well over 300 degrees. Firefighters disconnected the vehicle’s battery, after which the vehicle began to cool. Based on their initial observations, they indicated that the fire appeared to be electrical in nature. The vehicle had recently been filled with gasoline, which made the situation even more dangerous. Fortunately, no one was inside the Bronco, no other vehicles were parked nearby, and the fire department responded quickly. The vehicle has been transported to a repair facility but has not yet been inspected to determine the precise cause of the fire. I am extremely concerned that a nearly new vehicle could suddenly catch fire while turned off and parked, without any warning. This could have occurred while I was driving, with passengers inside, or while the Bronco was parked in my garage. Under those circumstances, the fire could have caused serious injury or death, destroyed my home, or endangered other people and property. I am submitting this complaint because I believe this incident presents a serious public-safety concern. I respectfully request that NHTSA investigate whether other 2025 Ford Bronco owners have experienced similar electrical fires and whether a defect exists that could place drivers, passengers, families, first responders, and the public at risk.
Crash:
No
Fire:
Yes
Injuries:
0
Deaths:
0
#11745336June 20, 2026
UNKNOWN OR OTHER
When the vehicle is in "Eco" mode, and an attempt is made to rapidly accelerate in an emergency situation, pressing the accelerator pedal to the floor results in a significant delay before *any* engine response is detected, far beyond what is reasonable for a normal gasoline powered vehicle. In several situations, I was in heavy traffic; traffic in the lane in which I was travelling was relatively slow. I attempted to change lanes into an adjacent lane in which traffic was moving much faster. When traffic allowed, I merged into the faster lane, and pressed the accelerator pedal to the floor. Prior to pressing the accelerator pedal, the vehicle was moving approximately 20 mph. Nothing happened for several seconds, and then the vehicle suddenly accelerated. During the period of non-response, traffic in the faster lane caught up to my vehicle. I am able to reproduce the issue 100%. The dealer's response is that "it's normal" (typical service response) and there was no attempt to investigate. I have driven several identical make/model vehicles belonging to friends, and one dealer vehicle (test drive) and they all exhibit the same issue. There are no warning lamps, errors, codes, or any indication that any system is faulty. The high latency in the throttle control system is clearly an ECU programming issue, and it increases the risk of collision. I have only observed this issue in models of this vehicle with an automatic transmission. I do own an identical model of this vehicle with a manual transmission, and this issue is not present.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11745106June 18, 2026
VISIBILITY/WIPER
I have a 2025 Ford Bronco Big Bend with 5233 miles. The windshield wipers stopped working. I checked the fuse and the fuse was good. I changed the fuse anyway and the wipers still do not work.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11744621June 16, 2026
ELECTRICAL SYSTEM
Window actuator does not properly open or close passenger window to open door properly, which is a safety risks to a child. Window could shatter because window will not roll down the inch or so to pull the door open. In order to open the door, the window will shake vibrantly and risk of a child of a possible window shatter. Ford says this is a normal wear and tear and it’s at owners cost to replace. To me that’s unacceptable.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11744590June 16, 2026
ENGINE
While driving on an interstate it was determined that the engine walls over compressed and blew out the sides of the motor of my 2022 Ford Bronco. The Bronco has 67,000 miles on it which shows a clear manufacturer defect. It is available to be inspected as well to confirm. My wife’s and unborn child’s safety was put at risk by losing acceleration and losing control of the vehicle briefly as it began to shake from the engine misfiring. This easily could have caused a serious wreck had more traffic been present at the time. The dealership has not been able to confirm this on other cars. The engine has been inspected by a Ford Dealership. There were no warning lamps or messages prior to the failure and only appeared shortly after the engine over-compressed and began to shake.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11744499June 16, 2026
SERVICE BRAKES
Its becoming more frequent and a huge safety issue. When you're driving the car, it feels like the emergency parking brake automatically engages. And when you push the brake pedal, it almost feels like it's dead, meaning there's no pressure back against your foot, which is really unusual for this vehicle, period. You don't necessarily lose control of the car, but you certainly don't have complete control of the braking system, period. Then you are in a period of time to get off the road safely and turn the vehicle off and restart it. Then the system seems to correct itself, and you can drive away. But I'm concerned about this from a safety perspective,
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11744471June 16, 2026
ENGINE, POWER TRAIN
The Incident: While operating the vehicle under high load, the driver received an explicit "Service Engine Soon" powertrain malfunction alert stating: "The powertrain control module lost communication with the vehicle active grill shutter module for a period of time." Immediately following this warning, the engine experienced a severe loss of power, followed by loud metallic banging from the engine bay. The vehicle stalled completely and lost all motive power, creating an imminent highway safety hazard.The Physical Damage: Subsequent mechanical teardown by the dealership revealed terminal block destruction, including deep vertical cylinder wall scoring, heavy unburnt liquid gasoline residue in the engine oil pan, and a blown head gasket.Relationship to Active Safety Defect: This catastrophic engine failure mirrors the progressive failure profile of NHTSA Campaign 25V455 / Ford Safety Recall 25S75 (Low-Pressure Fuel Pump Failure). In this EcoBoost architecture, the Active Grill Shutter (AGS) module shares critical voltage paths, grounding blocks, and wiring looms with the engine management and fuel delivery systems. The sudden network communication loss is diagnostic proof of a severe voltage drop or electrical short caused by the high-friction fuel pump degradation detailed in Recall 25S75. This circuit failure instantly starved the engine of fuel under turbo boost, inducing an extreme lean-out condition. The resulting pre-ignition forces violently shattered the internal piston rings (the loud banging), which then gouged the cylinder walls, wiped out compression, fouled the crankcase with fuel residue, and blew the head gasket.Request for Action: Ford's current VIN parameters for Recall 25S75 have not yet captured my specific vehicle despite it matching the exact production window, component setup, and catastrophic failure sequence. I am requesting that the NHTSA log this case as definitive evidence of consequential engine destruction originating from the 25V455 fue
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11744448June 16, 2026
ENGINE, POWER TRAIN
While operating the vehicle under load, the vehicle suffered a sudden and severe loss of engine performance, followed immediately by loud metallic banging from the engine bay. The vehicle lost all power and was immediately disabled (LIMP MODE), presenting an imminent highway safety hazard.The Physical Damage: Subsequent mechanical teardown revealed deep vertical cylinder wall scoring, heavy raw fuel residue in the engine oil pan, and a blown head gasket. Relationship to Active Safety Defect: This catastrophic block failure perfectly mirrors the progressive failure profile of NHTSA Campaign 25V455 / Ford Safety Recall 25S75 (Low-Pressure Fuel Pump Failure). Internal component degradation in the fuel tank delivery module dropped fuel pressure to the engine. Under turbo boost, this starvation induced an extreme, instantaneous lean-out condition. The resulting low-speed pre-ignition (LSPI) exploded and shattered the internal piston rings (the metallic banging), leading to mechanical wall gouging, unburnt fuel wash into the lower crankcase, and a secondary blown head gasket. Request for Action: Ford's current VIN parameters for Recall 25S75 have not yet captured my specific vehicle despite it matching the exact production window, component setup, and catastrophic failure sequence. I am requesting that the NHTSA log this case as clear evidence of consequential engine destruction originating from the 25V455 pump defect, and evaluate whether Ford's recall scope must be expanded to protect other consumers from highway engine failures.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11744346June 15, 2026
UNKNOWN OR OTHER, POWER TRAIN
Differential carrier replacement due to metal contmination being found in differential during oil change and a transmission overhaul due to excessive wear of(clutch container, CDF bushing, forward hub and front support bushings). They also noted a sticking valve in the main control on my 2022 Ford Bronco 2.7L V6 when taken in to dealership to evaluate vehichle under warranty due to ongoing intermittent thump/clunking noise when coming to a stop and accelerating from a stop as well as when backing up from a stop and while driving as well, intermittent loud metal slapping sound at speeds over 60 mph, intermittent jerking of vehichle when cycling through gears, unexpected downshift at high speeds. After differential replacement and transmission overhaul due to excessive wear while under warranty, my vehichle continues to experience the same symptoms and problems and feel this is a safety issue.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11744011June 14, 2026
SERVICE BRAKES, VEHICLE SPEED CONTROL
I was driving on the highway with standard cruise control (I don't have adaptive cruise) and I went to press the brakes and the brake pedal was SUPER stiff and I had to press unreasonably hard to disengage the cruise control and slow down. When the pedal finally gave, I ended up slamming on the bakes so much that my passenger was startled and we both lurched forward due to our momentum. Afterwards, my brake light light came on, on the dashboard. I went to AutoZone to get a reading and it said it was the brake assist vacuum or something like that. This could have caused a very bad accident in too different ways. One, if I didn't stop in time due to the delayed braking from the stiff pedal or getting rear ended due to inadvertently slamming on the brakes at highway speed.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11743709June 12, 2026
ENGINE, SEATS, ELECTRICAL SYSTEM
Description On your vehicle, it may be possible that one or more engine camshaft roller finger followers were not properly installed at the time of engine assembly. Safety Risk An improperly installed engine camshaft roller finger follower may result in engine failure, resulting in a no-start condition or a loss of motive power. A loss of motive power increases the risk of a crash. Your vehicle may also experience engine ticking or tapping noise, and or a low-volume oil leak due to this condition. Remedy A remedy is not yet available. Ford Motor Company is working to provide parts for this repair. When the remedy becomes available, Ford Motor Company will notify you via mail to schedule a service appointment with your dealer for repairs to be completed free of charge. The remedy is anticipated to be available 4TH quarter of 2026. Next Steps Contact your dealer for more information to schedule the free service. NOTE: Recall service not available right now. We have a remedy but parts are not available right now. We will inform you when the service is available. Or, you can contact your dealer.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11743635June 12, 2026
VISIBILITY/WIPER
Vehicle was parked in a secured location and the back windshield spontaneously broke more likely due to hot weather.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11743541June 11, 2026
STRUCTURE:BODY
The Molded-In-Color (MIC) hard top shows signs of delamination and cracking on the exterior skin of the roof panel. Models from the same production year were called under NHTSA Recall No.: 26V299. My vehicle was not included on this recall. I have attempted to have Ford inspect the issue and have refused since it is out of warranty. I am concerned that the delaminating sections will detach while driving.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11743451June 11, 2026
FUEL SYSTEM, GASOLINE
The contact owns a 2022 Ford Bronco. The contact received notification of NHTSA Campaign Number: 25V455000 (Fuel System, Gasoline); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was not made aware of the issue. The contact had not experienced a failure.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11742488June 6, 2026
SUSPENSION
I took my vehicle to the local Ford dealership for the remedy for recall Ford 25S01 on Feb 2, 2026. During the inspection, it was found that the part affected was damaged and the dealership sent photos to Ford. After that, I haven't received any guidance from Ford or the dealership. Since the invoice I received indicated that there was a weld crack in one of the absorbers, I assume that the recall should repair this as a safety concern, but I haven't received any proactive communication from Ford or the dealership. I have contacted the dealership twice since February but I have not received any callback. I am concerned that this is a safety issue and Ford hasn't done anything to correct this since they found out about the issue in February.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11742368June 5, 2026
UNKNOWN OR OTHER
Complete clutch failure at 39,000 miles. Unable to shift or safely restart vehicle once stopped. Clutch Hydraulic line came completely apart. Ford part number MB3Z-7A512-A. Failure verified by independent SAE certified mechanic. Note: Clutch and Brakes feed from the same reservoir, so loss of clutch hydraulic fluid also impacts entire braking system.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11742181June 4, 2026
FUEL SYSTEM, GASOLINE
The contact owns a 2022 Ford Bronco. The contact received notification of NHTSA Campaign Number: 25V455000 (Fuel System, Gasoline); however, the part to do the recall repair was not yet available. The local dealer was contacted; however, the vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0

← Back to Ford Bronco