BMW X6 Service Bulletins (2008)
246 manufacturer communications on file.
- October 1, 2015•Document ID: 10147759Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B110815
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary?N63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil.
Associated Products (56)Associated Documents - October 1, 2015•Document ID: 10147758Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- B070314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryThis Service Information bulletin supersedes SI B07 03 14 dated May 2015. designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Associated Products (142)Associated Documents - September 1, 2015•Document ID: 10147241Service Bulletin/Repair InstructionsWHEELS; POWER TRAIN:DRIVELINE
- Mfr Comm. #:
- B270415
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryShudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
Associated Products (176)Associated Documents - August 1, 2015•Document ID: 10151404Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- B270315
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryVibration or Shudder from Driveline when Accelerating from a Stop. Chassis stabilization warning is displayed. Vehicle may exhibit a shudder or vibration when taking off from a stop. One or more of the following fault codes may be stored: LMV ? 440101 - Transfer box (VTG): End of transmission service life reached ? 440105 - Transfer box (VTG ) Calibration Faulty ? 440115 - Transfer box (VTG): Calibration angle deviation outside tolerance? 44011B - Set torque outside of the torque characteristic curve EGS ? 420611 - DSC interface (wheel speed): non-permitted deviation of wheel speed (actual speed of wheel RL/FL/RR/FR, 0x254) from output speed and turbine speed DSC ? 48097D - Transfer box: Fault, clutch position known, only rear-wheel drive These symptoms or faults would be stored on a vehicle with low mileage (< 12,500 miles). CAUSE A front or rear differential with the incorrect gear ratio was installed in the car. The front and rear differentials need to be geared exactly the same for the xDrive to function properly.
Associated Products (142)Associated Documents - August 1, 2015•Document ID: 10151400Service Bulletin/Repair InstructionsEQUIPMENT; ENGINE
- Mfr Comm. #:
- B111715
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary"N63 and S63 Engine: Upper Oil Pan Removal and Installation Procedures. INFORMATION When removing and/or installing the N63 or S63 engine ""upper"" oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the upper oil pan bolts as per Repair Instruction 11 13 010 ""Removing and installing /replacing upper oil sump (N63),"" the steps outlined in the attachment of this bulletin must be followed. Refer to attached document and the instruction section that applies to the procedure being carried out. The ISTA/D repair instructions are currently being revised."
Associated Products (58)Associated Documents - July 1, 2015•Document ID: 10147192Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP
- Mfr Comm. #:
- B130215
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"?SI B13 02 15July 2015 Fuel SystemsTechnical Service This Service Information bulletin supersedes SI B13 02 15 dated May 2015. designates changes to this revision SUBJECT Service Action: N63 Replace High-Pressure Fuel Pumps. The high-pressure pump may fail, resulting in an engine malfunction warning and reduced engine output. This Service Action involves F01, F02, F04, F07, F10, F12, F13, E70, E71, and E72 vehicles with the N63 engine produced from January 1, 2011 to December 1, 2011. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. CAUSE The high-pressure pump quantity control valve may fail."
Associated Products (96)Associated Documents - July 1, 2015•Document ID: 10147188Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ENGINE
- Mfr Comm. #:
- B121015
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryN63: CBS Oil Service Conversion in ISTA/P. The CBS oil service conversion (8KL) performed for the N63 Customer Car Package and timing chain check (SI B11 16 14) did not work correctly for the above models with previous versions of ISTA/P. After the conversion, the forecast interval did not change to the desired 10,000 miles/12 months, or the forecast is displayed as an invalid value, for example: 25,000 miles/24 months. 1. Incorrect DME coding or calibration data 2. The ISTA CBS correction test plan contains an error when attempting to correct an invalid oil service prognosis value.
Associated Products (12)Associated Documents - July 1, 2015•Document ID: 10146935Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP; FUEL SYSTEM, OTHER:DELIVERY:FUEL PUMP
- Mfr Comm. #:
- B010515
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"In-Tank Fuel Delivery Module (Pump): Limited Warranty Extension to 10 Years Without Mileage Limitation. INFORMATION On the above-referenced vehicles, BMW of North America, LLC (""BMW NA"") is extending the limited warranty for the ? In-tank fuel delivery module (pump) to 10 years without mileage limitation as determined by the vehicle's original in-service date. Item #1: This ""component-specific"" limited warranty extension applies to This bulletin is notice of a ""limited warranty extension."" This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, BMW NA will begin sending VIN-specific customer notification letters the week of July 13, 2015 in a ""phased"" release. A sample letter is attached. ELIGIBLE BMW VEHICLES To assist you in identifying the eligible vehicles, the DCSnet Warranty Vehicle Inquiry will be updated with the ""Vehicle Comment"" shown below: BMW NA has extended the limited warranty for the in-tank fuel delivery module (pump) on this vehicle to 10 years without mileage limitation as determined from the original in-service date, subject to the applicable vehicle and coverage eligibility requirements, exclusions and limitations that apply to the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks. Please see SI B01 05 15. Note: Always check the DCSnet Warranty Vehicle Inquiry ""Vehicle Comments"" and the ""Repair History (Claims)"" sections first, before performing any repairs."
Associated Products (16)Associated Documents - July 1, 2015•Document ID: 10058994Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP
- Mfr Comm. #:
- SIB-01-05-15
- Date Added:
- January 9, 2016
- Manufacturer:
- BMW
SummaryBMW: TSB CONTAINS AN OWNER'S NOTIFICATION LETTER. SELECT DOCUMENT SEARCH BUTTON BELOW. INFORMATION PROVIDED REGARDING THE EXTENSION OF LIMITED WARRANTY ON THE IN TANK FUEL (PUMP) DELIVERY MODULE OF 10 YEARS WITHOUT MILEAGE LIMITATION, DEPENDING ON IN SERVICE DATE. INCLUDED DOCUMENT. *PE
Associated Products (7)Associated Documents - June 1, 2015•Document ID: 10147724Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- B650215
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryiDrive Controller Trim Peeling. The chrome ring on the iDrive controller is peeling. Poor chrome material adhesion.
Associated Products (77)Associated Documents - May 1, 2015•Document ID: 10147136Service Bulletin/Repair InstructionsTIRES:VALVE; WHEELS
- Mfr Comm. #:
- B360215
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryValve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015
Associated Products (219)Associated Documents - May 1, 2015•Document ID: 10147131Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- B130215
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryService Action: N63 Replace High-Pressure Fuel Pumps. The high-pressure pump may fail, resulting in an engine malfunction warning and reduced engine output.
Associated Products (89)Associated Documents - May 1, 2015•Document ID: 10147127Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B111614
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard."
Associated Products (56)Associated Documents - May 1, 2015•Document ID: 10147125Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B110815
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryN63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. ? B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs ? B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints ? B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity ? B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. ? Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine ? Excessive engine oil consumption ? Spark plugs fouled with engine oil
Associated Products (91)Associated Documents - May 1, 2015•Document ID: 10147123Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B070314
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryDiagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Associated Products (142)Associated Documents - May 1, 2015•Document ID: 10057338Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- SIB-11-16-14
- Date Added:
- May 20, 2015
- Manufacturer:
- BMW
SummaryBMW: ON CERTAIN VEHICLES, ENGINE TIMING CHAIN SHOULD BE CHECKED FOR EARLY STAGES OF WEAR, AND A REPAIR SOLUTION SHOULD BE PROVIDED. *PE UPDATED 9/25/15. *PE UPDATED 10/6/15. *PE
Associated Products (10)Associated Documents - April 1, 2015•Document ID: 10152303Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B121015
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
SummaryN63: CBS Oil Service Conversion in ISTA/P. The CBS oil service conversion performed for the N63 Customer Car Package and timing chain check (SI B11 16 14) does not work correctly for the above models with the current version of ISTA/P. After the conversion, the forecast interval does not change to the desired 10,000 miles/12 months, or the forecast is displayed as an invalid value, for example: 25,000 miles/24 months. 1. Incorrect DME coding or calibration data, which is being investigated. 2. The ISTA CBS correction test plan contains an error when attempting to correct an invalid oil service prognosis value.
Associated Products (12)Associated Documents - April 1, 2015•Document ID: 10152301Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- B110614
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
Summary"This bulletin outlines the Customer Care Package program that has been designed exclusively for BMW vehicles with the N63 engine. Vehicles with the N63 high performance engine are engineered with EfficientDynamics that provides fuel economy without compromising on its ""class leading"" power and performance. To ensure these engines keep delivering the ultimate performance, we have designed this Care Package that includes a 6 point check, and if necessary, the replacement of one or more of the following powertrain components: ? Hot-Film Air Mass Sensors ? PIEZO High Pressure Fuel Injectors ? Engine Vacuum Pump ? Fuel System Low Pressure Sensor/Feed Line ? Fresh Air Intake Turbo Seals ? Crankcase Ventilation Lines (Hoses) Note: Due to ongoing quality control monitoring, testing of the Bosch fuel system low-pressure sensor showed that replacement of the fuel system low-pressure sensor with Index 1 is no longer required in this customer care package. Refer to the attached procedure for the applicable replacement instructions regarding the fuel system low-pressure sensor. This engine care package also includes a multi-point inspection of the vehicle, including tire pressures, fluid levels, safety and convenience features. The N63CCP is NOT a mandatory Technical Campaign or Recall (per the authorities). It should only be completed based on parts availability, workshop capacity, and the customer's schedule. Complete all other applicable open Campaigns per the DCS Warranty inquiry and the Key Reader. Perform all recommended, due or qualifying ""time-based"" maintenance service task items as directed by the Key Reader/ISPA Light application. When eligible, also perform the procedure described in SI B61 30 14: 12-Volt Battery Replacement together with performing the N63 Customer Care Package. After completing all the necessary repairs, the vehicle needs to be road tested for 30 minutes to assure the highest standard of performed repairs (Please see ""Warranty Inf
Associated Products (59)Associated Documents - April 1, 2015•Document ID: 10058483Service Bulletin/Repair InstructionsFUEL SYSTEM, OTHER
- Mfr Comm. #:
- SIB-13-04-15
- Date Added:
- September 26, 2015
- Manufacturer:
- BMW
SummaryBMW: PROCEDURAL INFORMATION ON THE INSTALLATION OF FUEL SYSTEM LOW PRESSURE SENSOR AND NOT CORRECTLY INSTALLED WILL LEAD TO FAILURE OF LOW PRESSURE SENSOR AND METAL SUPPLY LINE. MODEL 2008-14. *PE
Associated Products (11)Associated Documents - March 1, 2015•Document ID: 10147669Service Bulletin/Repair InstructionsPOWER TRAIN:DRIVELINE:DRIVESHAFT
- Mfr Comm. #:
- B260114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryDriveshaft Technical Service. This Service Information bulletin supersedes SI B26 01 14 dated August 2014. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. designates changes to this revision SUBJECT Service Action: Inspect Front Driveshaft. The universal joints in the front driveshaft may wear out prematurely.
Associated Products (14)Associated Documents