BMW 535d Service Bulletins (2014)
351 manufacturer communications on file.
- October 1, 2014•Document ID: 10149355Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 130514
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary. INFORMATION To properly diagnose the customer's complaint, the applicable test plan for the misfire faults stored in the DME must be performed to avoid repeat repairs. If a misfire fault is not stored in the DME memory and an engine related drivability complaint is received, follow the path below to manually start the misfire test plan (AT1214_TVD4_MISFIRE_20): 1. Perform a vehicle test. 2. Select "Function Structure." 3. Select "01 Engine." 4. Select "Engine electronics MEVD." 5. Select "Misfire detection." 6. Follow the steps in the test plan and select "Basic check (start)" first. Do not select "Additional check" at this time. 7. If the result of the "Basic check" indentifies a fuel system component failure, replace the identified component. If the result of the "Basic check" test plan was inconclusive, go to step 7. After the component replacement, perform the "Basic check" portion of the test plan again to verify if the diagnosis was correct and the vehicle condition has been rectified.
Associated Products (58)Associated Documents - October 1, 2014•Document ID: 10149353Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 130114
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryN47T and N57T Diesels with SCR Efficiency Faults Stored. A. The Service Engine Soon lamp is on (MIL) with either or both of the following SCR efficiency faults stored in the DDE: 26F500 - SCR system, efficiency: Efficiency too low 26F600 - SCR system, efficiency: Efficiency too low B. In addition, a Check Control message of "Incorrect diesel exhaust fluid" may be displayed with "no start scenario countdown" active. This would cause any of the following additional faults to be stored, depending on the SCR system status at the time. 2C4E00 - SCR system: System error and poor urea/water mixture quality detected 26FD00 - Reducing agent metering, long-term adaptation: Adaptation value too high 29FB00 - SCR system, warning and deactivation scenario: Warning level 1 29FC00 - SCR system, warning and deactivation scenario: Warning level 2 CAUSE Unfavorable DDE software
Associated Products (20)Associated Documents - October 1, 2014•Document ID: 10149282Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 111414
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryEngine Damage Due to Debris in Oil Passages. After performing extensive engine repairs (e.g., cylinder head removal), the engine begins to knock and may lose power. Debris has entered the engine oiling passages during cleaning of the engine block and cylinder head mating surfaces during engine repair.
Associated Products (93)Associated Documents - October 1, 2014•Document ID: 10149278Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 011314
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryBMW Customer-Focused Satisfaction (CFS) Program. Based on customer feedback, BMW has determined that during the first three years of service, some vehicles may require specific additional service work. BMW of North America, LLC ("BMW NA") is pleased to announce the Customer-Focused Satisfaction (CFS) Program. This new program's procedure will be available for your center to address these customers' concerns, starting with claim repair dates on or after September 1, 2014. As part of our pledge to deliver the ultimate BMW driving experience, for the above-referenced BMW vehicles, we developed this program to increase our customers' satisfaction by helping to prevent unexpected repair visits.
Associated Products (36)Associated Documents - September 1, 2014•Document ID: 10148039Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS; ELECTRICAL SYSTEM; EXTERIOR LIGHTING
- Mfr Comm. #:
- 630514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Adaptive Headlight Malfunction in Cold Weather. * In very cold weather conditions (32ºF or below) with the light switch in the automatic position, the CCM (Check Control Message) ""Adaptive headlight malfunction"" is displayed. * When the CC message is displayed, all the lights continue to function. * When switching the headlights to high beam and the headlight unit is cold, the mechanism inside the headlight is too stiff to move. Software error in TMS 3 (headlight driver module AHL, xenon headlight)"
Associated Products (40)Associated Documents - September 1, 2014•Document ID: 10148025Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; ENGINE
- Mfr Comm. #:
- 130314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Engine Soon Lamp (MIL) On with NOx Sensor Faults Stored. The Service Engine Soon lamp (MIL) is on with either of the following nitrogen oxide (NOx) sensor faults stored: * 2B6200 - NOx sensor before DeNOx catalytic converter, plausibility: Sensor self-diagnosis of sensitivity * 2B6300 - NOx sensor After DeNOx catalytic converter, plausibility: Sensor self-diagnosis of sensitivity These stored faults would not cause a problem with engine performance. This NOx self-diagnostic routine is performed only after the engine has been shut off. In some situations, the diagnostic function of both NOx sensors can be too sensitive when sampling the residual exhaust gases, leading to an erroneous fault being set. Unfavorable DDE software diagnostics
Associated Products (7)Associated Documents - August 1, 2014•Document ID: 10148381Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:LABELS; ENGINE AND ENGINE COOLING:ENGINE:DIESEL
- Mfr Comm. #:
- 710214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Replace Emission Label. Certain 2015 model year vehicles with N47T and N57T diesel engines were produced with an "emissions" label which contains incorrect information pertaining to the 2015 model year. Affected vehicles in dealer inventory must not be retailed or delivered until this issue is corrected. Vehicles at VDCs will be repaired prior to dealer delivery.
Associated Products (66)Associated Documents - August 1, 2014•Document ID: 10148380Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- 651614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCentral Information Display Intermittently Dimming or Flashing Off/On. Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue. Cause 1: Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher Cause 2: Calibration data for dimming the Central Information Display (CID) at high temperatures or bright sunlight is set incorrectly internally in the CID.
Associated Products (68)Associated Documents - August 1, 2014•Document ID: 10148227Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; STRUCTURE:BODY:DOOR; LATCHES/LOCKS/LINKAGES:DOORS:LATCH
- Mfr Comm. #:
- 511714
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryRattling Noise from Mid-range Speaker in Front Door Panel. The customer complains of a rattle noise in either the left or right front door only when the speakers are in use. The inside door lock rod is making contact with the inside panel when the speakers are in use at certain volume and frequency levels.
Associated Products (22)Associated Documents - August 1, 2014•Document ID: 10148226Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT
- Mfr Comm. #:
- 511613
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryBang & Olufsen Sound System: Loudspeaker Cover Rattles. The top center loudspeaker cover rattles when driving on rough roads. CAUSE Poor loudspeaker cover fitment to the speaker assembly.
Associated Products (67)Associated Documents - August 1, 2014•Document ID: 10148218Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS
- Mfr Comm. #:
- 130514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN20 and N26 Injector Replacement. INFORMATION When a defective high-pressure fuel injector is identified with an index "02" designation, as shown in the illustration below, all 4 injectors must be replaced at the same time. This bulletin only applies to index "02" injectors. Index "01" and index "03" or higher are not affected. No immediate repair is required unless the BMW vehicle is currently experiencing this problem.
Associated Products (58)Associated Documents - August 1, 2014•Document ID: 10148216Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE)
- Mfr Comm. #:
- 111314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN57T Diesel with Fault Code 29EB00: EGR Cooling Plausibility. The Service Engine Soon lamp is on (MIL) with the following fault stored in the DDE: 29EB00 - EGR cooling, plausibility: Exhaust-gas recirculation cooler bypass flap faulty or cooler efficiency too low CAUSE Unfavorable DDE software.
Associated Products (4)Associated Documents - August 1, 2014•Document ID: 10148215Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT
- Mfr Comm. #:
- 011314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryBMW Customer-Focused Satisfaction (CFS) Program. Based on customer feedback, BMW has determined that during the first three years of service, some vehicles may require specific additional service work. BMW of North America, LLC ("BMW NA") is pleased to announce the Customer-Focused Satisfaction (CFS) Program. This new program's procedure will be available for your center to address these customers' concerns, starting with claim repair dates on or after September 1, 2014. As part of our pledge to deliver the ultimate BMW driving experience, for the above-referenced BMW vehicles, we developed this program to increase our customers' satisfaction by helping to prevent unexpected repair visits.
Associated Products (37)Associated Documents - July 1, 2014•Document ID: 10148135Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- 840214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryConnectedDrive/BMW Assist System Diagnosis Information. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
Associated Products (217)Associated Documents - July 1, 2014•Document ID: 10148132Service Bulletin/Repair InstructionsFORWARD COLLISION AVOIDANCE
- Mfr Comm. #:
- 660414
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryFront Collision Warning Check Control Message Displayed in CID. Occasionally while driving, a check control message (CCM) for Front Collision Warning is displayed in the Central Information Display (CID). This message is cleared from the CID by clicking on "OK" using the iDrive controller. CAUSE The KAFAS (camera-based driver support system) camera is affected by environmental conditions such as: * Direct sunlight (sunrise or sunset) * Rain * Fog * Dirt * Snow * Ice * High interior temperatures (may also cause a CCM to be displayed upon starting the vehicle) ?? Fault code 0x800AC0 - KAFAS camera switch off due to over temperature The pictures below show the direct sunlight causing the CCM: INFORMATION This is the current text in the Owner's Manual for the Front Collision Warning (FCW): The system may not be fully functional in the following situations: * In heavy fog, rain, sprayed with water or snowfall * In tight curves * If the driving stability control systems are limited or deactivated: for example, the DSC is off. * If the camera view field of the front windshield is dirty or covered. * Up to 10 seconds after the start of the engine, via the Start/Stop knob. Direct sunlight will be added as one of the causes for the FCW CCM.
Associated Products (94)Associated Documents - July 1, 2014•Document ID: 10148130Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; SEATS
- Mfr Comm. #:
- 652113
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryWhen Unlocking with Comfort Access the Outside Door Mirrors Are in the Wrong Position. The vehicle is locked with one remote key and then enters sleep mode. The vehicle is then unlocked using one of the outside door handles with the second remote key. The outside door mirrors do not move to the correct position. The seats do move into the correct position. CAUSE Software error in driver's seat module
Associated Products (78)Associated Documents - July 1, 2014•Document ID: 10148129Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 651614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCentral Information Display Intermittently Dimming or Flashing Off/On. Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue. Cause 1: Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher Cause 2: Calibration data for dimming the Central Information Display (CID) at high temperatures or bright sunlight is set incorrectly internally in the CID.
Associated Products (70)Associated Documents - July 1, 2014•Document ID: 10148128Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 650214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHeadunit High Is Constantly Resetting. After connecting a mobile device via Bluetooth, the Headunit High (HU-H) constantly resets. This is because the mobile device paired/connected to the vehicle contains one or more emails with 30 or more recipients. Note: In this situation, a reset is when the HU-H shuts down and then turns back on. CAUSE Software error in the HU-H.
Associated Products (81)Associated Documents - July 1, 2014•Document ID: 10148120Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 610314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCheck Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut
Associated Products (248)Associated Documents - July 1, 2014•Document ID: 10148116Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 130314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Engine Soon Lamp (MIL) On with NOx Sensor Faults Stored. The Service Engine Soon lamp (MIL) is on with either of the following nitrogen oxide (NOx) sensor faults stored: * 2B6200 - NOx sensor before DeNOx catalytic converter, plausibility: Sensor self-diagnosis of sensitivity * 2B6300 - NOx sensor After DeNOx catalytic converter, plausibility: Sensor self-diagnosis of sensitivity These stored faults would not cause a problem with engine performance. This NOx self-diagnostic routine is performed only after the engine has been shut off. In some situations, the diagnostic function of both NOx sensors can be too sensitive when sampling the residual exhaust gases, leading to an erroneous fault being set. Unfavorable DDE software diagnostics
Associated Products (7)Associated Documents