BMW 325i Service Bulletins (2006)
114 manufacturer communications on file.
- January 11, 2024•Document ID: 10249027Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B611305
- Date Added:
- February 1, 2024
- Manufacturer:
- BMW
SummaryThe electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle âÂÂdischarged batteryâ complaints.
Associated Products (1018)Associated Documents - April 1, 2021•Document ID: 10194296Service Bulletin/Repair InstructionsSERVICE BRAKES, AIR:DISC; STEERING: STEERING WHEEL/HANDLE BAR
- Mfr Comm. #:
- B340414
- Date Added:
- May 24, 2021
- Manufacturer:
- BMW
SummaryDiagnosis of Compound Brake System Complaints in M Vehicles: 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form.
Associated Products (232)Associated Documents - October 1, 2020•Document ID: 10182619Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM
- Mfr Comm. #:
- B611305
- Date Added:
- November 16, 2020
- Manufacturer:
- BMW
SummaryDischarged Battery Energy Diagnosis Must Be Performed: The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle "discharged battery" complaints. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion, with all results taken into consideration. Without performing the energy diagnosis test plan, the root cause of the discharged battery cannot be identified. This increases the chances of a repeat repair.
Associated Products (250)Associated Documents - September 1, 2020•Document ID: 10181214Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- B110208
- Date Added:
- October 19, 2020
- Manufacturer:
- BMW
SummaryPower Reduction, FC2A82 Intake VANOS and/or FC2A87 Exhaust VANOS Camshaft Fault: The ?Service Engine Soon? (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If theignition is cycled, the engine then usually performs normally.
Associated Products (70)Associated Documents - April 1, 2020•Document ID: 10175267Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; POWER TRAIN
- Mfr Comm. #:
- B110208
- Date Added:
- May 18, 2020
- Manufacturer:
- BMW
SummaryPower Reduction FC2A82 Intake VANOS and/or FC2 A87 Exhaust VANOS Camshaft Fault: The "Service Engine Soon" (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled the engine then usually performs normally.
Associated Products (140)Associated Documents - July 10, 2019•Document ID: 10162431Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 613312
- Date Added:
- July 11, 2019
- Manufacturer:
- BMW
Summary"Erroneous CC Message "Remote control! Do not switch off the engine" is Displayed. An erroneous CC message, "Remote control!" " Do not switch off the engine" is displayed in the Central Information Display (CID). The engine can still be started, even with the CC message displayed. CAUSE: Car Access System (CAS) software error"
Associated Products (63)Associated Documents - July 10, 2019•Document ID: 10162426Service Bulletin/Repair InstructionsLATCHES/LOCKS/LINKAGES:TRUNK LID:LOCK; STRUCTURE:BODY:TRUNK LID
- Mfr Comm. #:
- 513911
- Date Added:
- July 11, 2019
- Manufacturer:
- BMW
SummaryTrunk Lid Intermittently Does Not Open or Latch. Intermittently the trunk lid does not pop open when using the remote, or latch when closing. If the vehicle is driven and the trunk is not closed fully, a Check Control message will be displayed in the instrument cluster. CAUSE: The trunk lid is out of tolerance. When opening or closing the trunk lid, the latch rubs against the striker because of insufficient clearance.
Associated Products (25)Associated Documents - July 10, 2019•Document ID: 10162406Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 610405
- Date Added:
- July 11, 2019
- Manufacturer:
- BMW
SummaryPower Mirrors and/or Windows are Inoperative. The power windows and/or power mirrors are inoperative. The LED on the headlight switch is flashing. There is a check control message for Windows/Mirrors/ Headlights. There may also be a complaint of water in one or both headlights. One of the following fault codes may be stored: * 9CBD - Communication with stepper motor box left defective * 9CBE - Communication with stepper motor box right defective * 9CC1 - Communication with mirror driver side defective * 9CC2 - Communication with mirror passenger side defective/Right Stepper Motor Controller (SMC) signaling fault * 9CCF - Communication with LIN control defective Left and/or right headlight housing cover is not properly fitted allowing water ingress into the Stepper Motor Controller (SMC) connector. CAUSE: Left and/or right headlight housing cover is not properly fitted allowing water ingress into the Stepper Motor Controller (SMC) connector.
Associated Products (30)Associated Documents - July 10, 2019•Document ID: 10162404Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR
- Mfr Comm. #:
- 513608
- Date Added:
- July 10, 2019
- Manufacturer:
- BMW
Summary"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Follow the diagnosis test plan using the latest ISTA version. In Information Search, select the "Function Structure"" tab. Select Body, Mirror, Door mirror, Driver's or passenger side, Exterior Mirror Malfunction, and then press "Start Search". Select test plan ""AM5102_00010".
Associated Products (72)Associated Documents - July 9, 2019•Document ID: 10162416Service Bulletin/Repair InstructionsEQUIPMENT; ENGINE
- Mfr Comm. #:
- 110208
- Date Added:
- July 9, 2019
- Manufacturer:
- BMW
Summary"Power Reduction, FC 2A82 Intake VANOS and/or FC 2A87 Exhaust VANOS Camshaft Faults are Stored in DME. The ""Service Engine Soon"" (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled, the engine then usually performs normally. The following faults are stored in the DME: * 2A82 VANOS intake - stiff; jammed mechanically * 2A87 VANOS exhaust - stiff; jammed mechanically * 130108 VANOS intake: control fault, position not reached * 130308 VANOS exhaust: control fault, position not reached For the N54 engine, the following secondary faults may also be stored: * 120408 Charge-air pressure control, cut-out: Boost pressure accumulation blocked * 3100 Boost-pressure control, deactivation - boost-pressure buildup prohibited CAUSE The VANOS faults can be caused by an insufficient oil pressure supply to the inlet VANOS adjustment unit. To effectively move the camshafts to the target positions in the specified time and under all engine conditions, sufficient oil pressure supply to the VANOS control pistons must always be available. If engine operation requires the VANOS system to quickly advance or retard the intake or exhaust camshaft, faults may be stored if the camshaft is ""late"", or does not reach the target position. In this situation, engine power may be reduced and a check control message is displayed. The consequential fault 3100 or 120408 can also be set in the DME fault memory as well."
Associated Products (66)Associated Documents - July 9, 2019•Document ID: 10162395Service Bulletin/Repair InstructionsEQUIPMENT; ENGINE AND ENGINE COOLING; EQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- 121412
- Date Added:
- July 10, 2019
- Manufacturer:
- BMW
SummaryN55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine has a loss of power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.
Associated Products (81)Associated Documents - April 1, 2019•Document ID: 10160287Service Bulletin/Repair InstructionsAIR BAGS
- Mfr Comm. #:
- B013118
- Date Added:
- May 20, 2019
- Manufacturer:
- BMW
SummaryTAKATA AIR BAG RECALL-RELATED SHORT-TERM ALTERNATE TRANSPORTATION AND CONSEQUENTIAL REPAIRS This Service Information bulletin supersedes SI B01 31 18 dated October 2018.
Associated Products (143)Associated Documents - April 1, 2019•Document ID: 10160244Service Bulletin/Repair InstructionsAIR BAGS
- Mfr Comm. #:
- B013118
- Date Added:
- May 20, 2019
- Manufacturer:
- BMW
SummaryTAKATA AIR BAG RECALL-RELATED SHORT-TERM ALTERNATE TRANSPORTATION AND CONSEQUENTIAL REPAIRS This Service Information bulletin supersedes SI B01 31 18 dated October 2018.
Associated Products (147)Associated Documents - January 1, 2019•Document ID: 10153726Service Bulletin/Repair InstructionsAIR BAGS; AIR BAGS: AIR BAG/RESTRAINT CONTROL MODULE
- Mfr Comm. #:
- B011618
- Date Added:
- February 25, 2019
- Manufacturer:
- BMW
SummaryTAKATA CLASS ACTION SETTLEMENT. CUSTOMER SUPPORT PROGRAM. FRONT DRIVER SIDE AIRBAG MODULES.
Associated Products (145)Associated Documents - October 1, 2018•Document ID: 10149557Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; AIR BAGS
- Mfr Comm. #:
- B011618
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryFor the above-referenced vehicles with driver?s side airbag modules, BMW of North America, LLC (?BMW NA?) will provide a Customer Support Program as outlined in the Takata Settlement Customer Support Program Overview attachment. This ?component-specific? customer support program applies only if there is a defect in materials or workmanship of the Takata driver?s side airbag module in a listed vehicle.
Associated Products (145)Associated Documents - July 1, 2018•Document ID: 10145320Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- B840214
- Date Added:
- October 9, 2018
- Manufacturer:
- BMW
SummaryCONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION: ConnectedDrive/BMW Assist features are partially or completely inoperative.
Associated Products (247)Associated Documents - June 1, 2018•Document ID: 10145306Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- B650709
- Date Added:
- October 9, 2018
- Manufacturer:
- BMW
SummaryNAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
Associated Products (361)Associated Documents - May 1, 2018•Document ID: 10143564Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- B650709
- Date Added:
- August 6, 2018
- Manufacturer:
- BMW
SummaryNAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
Associated Products (361)Associated Documents - February 1, 2018•Document ID: 10154816Service Bulletin/Repair InstructionsAIR BAGS
- Mfr Comm. #:
- B080119
- Date Added:
- March 18, 2019
- Manufacturer:
- BMW
SummaryIn an effort to improve the completion rate on Takata air bag recall affected vehicles; BMW NA has expanded the BMW Ultimate Rewards platform to include a new Recall Support page. This page will allow IRFs to check their customers VINs for open Takata recalls; and get rewarded for helping us with completing repairs.
Associated Products (130)Associated Documents - January 1, 2018•Document ID: 10142910Service Bulletin/Repair InstructionsSEATS
- Mfr Comm. #:
- B010118
- Date Added:
- July 16, 2018
- Manufacturer:
- BMW
SummaryFRONT PASSENGER SEAT OCCUPANCY (OC3) MAT FOR SRS: LIMITED WARRANTY EXTENSION TO 15 YEARS/UNLIMITED MILES
Associated Products (27)Associated Documents