Toyota · Model Report
Showing safety data for the 2018 model year only.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2018-2019 4Runner, 2019-2020 Avalon, 2019 Corolla Hatchback, 2017-2019 Highlander, 2018-2020 Camry, 2020 Corolla, 2018-2019 Land Cruiser, 2017-2020 Tacoma, 2019-2020 RAV4, 2019-2020 Sequoia, 2017-2020 Sienna, 2019-2020 Tundra, 2018-2020 Lexus ES350, 2017 Lexus GS200t, 2017-2019 Lexus GS350, 2019 Lexus GS300, 2018-2020 Lexus LC500h, 2019-2020 Lexus LS500, 2018-2019 Lexus GX460, 2017 Lexus IS200t, 2019 Lexus IS300, 2019 Lexus IS350, 2018-2020 Lexus LC500, 2018 Lexus LS500, 2019 Lexus LS500h, 2018-2019 Lexus LX570, 2017 Lexus RC200t, 2019 Lexus RC300, RC350, 2017 and 2019-2020 Lexus RX350, 2018-2020 RX350L, 2019 Lexus UX200, 2018-2019 Lexus NX300 vehicles. The low-pressure fuel pump inside the fuel tank may fail.
Toyota Motor Engineering & Manufacturing (Toyota) recalled certain 2018-2019 4Runner, Highlander, Camry, Land Cruiser, Sequoia, Sienna, Tacoma and Tundra, and Lexus RC 300, RC 350, GS 350, GX 460, IS 300, LC 500, LS 500, LX 570, RX 350L, and 2019 Toyota Avalon and Corolla, and certain Lexus NX 300, and ES 350 vehicles on January 13, 2020. On March 4, 2020, Toyota expanded the recall to include certain 2014-2015 Toyota 4Runner and Land Cruiser, 2018 Avalon, Corolla, 2014 FJ Cruiser, 2017 Sienna and Lexus 2018 ES 350, 2018-2019 GS 300, 2013-2014 GS350, 2014-2015 GX 460, IS 350 and LX 570, 2014 IS F, 2018-2019 IS 350, LC 500H and LS 500H, 2013-2015 LS 460, 2015 NX 200T and RC350, 2017 RC 200T and RX 350. Toyota also removed the 2018-2019 Toyota 4Runner and Land Cruiser and 2018-2019 Lexus GX 460 and LX 570 and 2019 NX300 from inclusion in this recall. On March 19, 2020, Toyota expanded the recall to include 2015 Lexus GS350 vehicles. The low-pressure fuel pump inside the fuel tank may fail.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2018-2019 Toyota Tacoma vehicles. Improper machining of the brake master cylinder may result in internal damage of one of the seals, affecting brake performance.
I have been having issues with an intermittent rain smell in my vehicle for the past few months not realizing the smell was due to water intrusion in the cabin of my truck. I own a 2018 Toyota Tacoma. As of recently the situation has been getting exceedingly worse due to stormy and rainy weather during the month of September. At this point I noticed the floor throughout my whole cabin was flooded with water. I was sure my windows were not open and my doors were closed and sealed properly. I took the vehicle to the Honda dealership and they provided me a Condition, Cause and Remedy (CCR). The CCR stated that water was entering my vehicle through the cabin vents located between my truck bed and the cabin of the vehicle. These cabin vents do not have any maintenance plan surrounding them, the seals are also not accessible or visible without complete removal of the back end of the truck. This is a manufacturer design issue and Toyota needs to warn their consumers to correct. Also because water intrudes in the vehicle it builds up moisture on the drivers windshield so you cannot see when driving early in the morning. The defroster does not help reduce visibility enough while driving. I was quoted a repair cost of $4500 by the Toyota dealership to fix. There is now mold growing through the only vehicle I own. I reached out to Toyota customer service to help get this resolved. It’s been over a week and they closed my case without providing any assistance or solution despite acknowledging the design issue. This is a common issue with Gen 3 Tacomas and driving with mold growing in your vehicle is NOT safe. I will follow up with my doctor to see if this problem is contributing to some of the current health issues I am experiencing.
No injuries · No fire · No crash
Cab air vents behind rear seat leaks causing mold to form under carpet.
No injuries · No fire · No crash
2018 Toyota Tacoma SR 4WD Double Cab, 3.5L V6 (2GR-FKS). At about 87,000 miles the check engine light came on with code P11EC, Cylinder 1 Air-Fuel Ratio Imbalance (Port). Cylinder 1 failed compression. Leakdown and coolant tests had passed earlier; borescope did not show heavy scoring. The Toyota dealer said replacing the direct injectors would fix compression (quote about $4,499). After the dealer injector repair, cylinder 1 was still 124 psi (spec about 142-180 psi), so it did not fix compression. The dealer then quoted $11,778 for a short block (+$500 incidentals) and $14,238 for an engine assembly that was not new (about 45,000 miles on the replacement discussed); adding injectors again put the short-block path at about $16,278. I was steered toward buying a new truck and had the injector work reversed because it did not fix what they said it would. Toyota Brand Engagement Center reviewed the case, called the dealer, took VINs for other Toyotas, and denied goodwill; no recall or TSB. An independent shop later pulled the engine and found the cylinder 1 exhaust valves leaking badly; cylinder wall still looked good. Machine shop valve job, new rings, injectors tested (two bad), all six replaced; repair about $8,000. Truck runs normally after. Consequences: loss of power, failed emissions monitors, risk of further engine damage if driven, high repair cost. Not a crash. This appears to be a known pattern on the 2GR-FKS in 2016-2019 Tacomas (P11EC, cylinder 1, leaking/burnt exhaust valves, often after direct-injector washdown). Toyota has not recalled; dealers stop at injectors or quote a short block/used engine, and owners pay out of warranty. Please log this under 2018 Toyota Tacoma: engine, fuel system, and valve train (cylinder head/exhaust valves, fuel injectors), so the pattern is on record. Servicing dealer: Nashville Toyota North. Toyota Brand Engagement case 260521000967.
No injuries · No fire · No crash
Rear cabin air vents not sealed properly from factory. Water leaks in and soaks interior carpet and gets moldy.
No injuries · No fire · No crash
The contact owns a 2018 Toyota Tacoma. The contact stated that while driving 65 MPH, the brake pedal was depressed and went to the floorboard, and the vehicle continued moving forward. The vehicle was taken to the local dealer and was repaired under NHTS Campaign Number: 18V888000 (Service Brakes, Hydraulic); but the contact had evidence that the repair was not performed. There was an abnormal fuel odor inside and outside of the vehicle before the failure, which continued afterwards. The manufacturer was informed through brand engagement and customer care. The failure mileage was approximately 8,000.
No injuries · No fire · No crash