MINI Cooper Coupe Service Bulletins
144 manufacturer communications on file.
- January 1, 2014•Document ID: 10147956Service Bulletin/Repair InstructionsENGINE; ELECTRICAL SYSTEM
- Mfr Comm. #:
- M110112
- Date Added:
- November 13, 2018
- Manufacturer:
- MINI
Summary"N16 and N18 Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid. DIAGNOSTIC Below is the procedure for identifying how far the engine oil has migrated inside the engine electrical harness, when this issue occurs, if at all. The procedure must be followed very carefully so that the proper repair is identified. 1. Disconnect the oil pump volume control solenoid valve electrical connection per Repair Instructions 11 41 519 ""Removing and installing or replacing the solenoid valve (engine oil pump)."" Inspect the electrical connector; if no engine oil is found inside the electrical connector, perform the oil pump volume control valve repair procedure. If engine oil is found inside the electrical connector, proceed to diagnostic procedure step 2. 2. Remove the cover from the DME and remove all three electrical connectors from the DME. Inspect the connectors for traces of engine oil. If no engine oil is found, perform the oil pump volume control valve repair procedure and replace the engine section of the wire harness. Refer to EPC for the additional part number. If engine oil is found in the DME connector, proceed to step 3. 3. If engine oil is found in the DME electrical connector, perform the oil pump volume control valve repair procedure, replace the engine section of the wire harness and replace the DME. Refer to EPC for the additional part numbers. Do not remove the engine oil pan. Do not replace the oil pump volume control valve. Do not replace engine oil pump. OIL PUMP VOLUME CONTROL VALVE REPAIR"
Associated Products (14)Associated Documents - January 1, 2014•Document ID: 10044680Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- SIM-11-01-12
- Date Added:
- July 25, 2012
- Manufacturer:
- MINI
SummaryMINI: ON CERTAIN MODEL VEHICLES, AN ENGINE OIL LEAK MAY OCCUR, DUE TO THE COMPROMISED OIL PUMP VOLUME CONTROL SOLENOID VALVE, FROM THE UNDERSIDE OF ENGINE. NO MODEL YEARS LISTED. *PE UPDATED 4/19/2013. *KB UPDATED 3/11/14. *PE
Associated Products (13)Associated Documents - November 1, 2013•Document ID: 10150207Service Bulletin/Repair InstructionsSTRUCTURE
- Mfr Comm. #:
- M540513
- Date Added:
- December 3, 2018
- Manufacturer:
- MINI
Summary"Service Action: Convertible Top Does Not Close. During the closing process, it is possible that the convertible top locating pin on the right side is not correctly positioned in the landing plate at the top of the A-pillar (passenger's side). AFFECTED VEHICLES This Service Action affects certain R57 vehicles produced from July 2013 to October 2013. 3.This picture shows the left side locating pin correctly positioned in the landing plate on the driver's side A-pillar. 4.The passenger's side should In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for code number 63. If code number 63 has been punched out, the campaign has already been performed. If code number 63 has not been punched out, it will be necessary to utilize the "Service Menu" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action. Important Note: A Campaign can be reserved in ISPA Light as "Pending" prior to submission of a claim. If you find this Campaign reserved, please verify the reason before attempting to perform this repair."
Associated Products (8)Associated Documents - November 1, 2013•Document ID: 10150205Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC
- Mfr Comm. #:
- M340113
- Date Added:
- December 3, 2018
- Manufacturer:
- MINI
Summary"?SI M34 01 13 November 2013 BrakesTechnical Service This Service Information bulletin supersedes SI 34 01 13 dated October 2013. designates changes to this revision SUBJECT Erroneous ""Service due"" Message Though Brake Lining Thickness Sufficient. The CBS data calculated for the remaining distance of the front and/or rear brake pads does not agree with the actual brake pad thickness. The yellow brake lining service due indicator illuminates even though the pad thickness is greater than the minimum wear limit (approximately 3.7 mm); the brake wear sensor has not yet been activated (from a thickness of approx. 4.2 mm). In some cases, the red warning message may already be active. The CBS front/rear brake display is based on a mathematical calculation. Various influences are incorporated into this calculation (for example, vehicle speed, brake pressure, and rotor temperature). Due to changing driving characteristics and/or unfavorable environmental conditions, the calculated remaining distance may differ from actual pad thickness."
Associated Products (12)Associated Documents - November 1, 2013•Document ID: 10150203Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- M120113
- Date Added:
- December 3, 2018
- Manufacturer:
- MINI
SummaryN16 Engine: FC 2D9B Knock Sensor, Signal Is Stored in the DME. Certain areas of the US experience extremely cold climate conditions during the winter months, which can cause the Service Engine Soon lamp to illuminate while the engine temperature is increasing to full operating temperature. The following fault may be stored in the DME: ??FC 2D9B Knock Sensor, Signal CAUSE Unfavorable DME knock sensor diagnostic at outside ambient temperatures below -5° C
Associated Products (13)Associated Documents - November 1, 2013•Document ID: 10150198Service Bulletin/Repair InstructionsSTRUCTURE
- Mfr Comm. #:
- BMWNOV1113
- Date Added:
- December 3, 2018
- Manufacturer:
- MINI
SummaryThis is an update to the Delivery Stop that was issued on certain 2014 model year MINI Cooper, Cooper S and John Cooper Works Convertibles produced between July and October 2013. During closing, it is possible that the convertible top locating pin is not correctly positioned in the landing plate, at the top of the A-pillar (passenger?s side). The repair procedure is pending the release of warranty information which is expected shortly. Dealers will be updated via DCS as soon as this occurs. Affected vehicles in dealer inventory must not be delivered until the Service Action has been completed. A chassis number list of affected vehicles can be found as an attachment to this message.
Associated Products (8)Associated Documents - November 1, 2013•Document ID: 10150190Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- BMWNOV0313
- Date Added:
- December 3, 2018
- Manufacturer:
- MINI
SummaryThis is an update to the Delivery Stop that was issued on certain 2014 model year MINI Cooper, Cooper S and John Cooper Works Convertibles produced between July and October 2013. During closing, it is possible that the convertible top locating pin is not correctly positioned in the landing plate at the top of the A-pillar (passenger?s side). The repair procedure is now available in Service Information bulletin M54 05 13. Affected vehicles in dealer inventory must not be delivered until the Service Action has been completed. A chassis number list of affected vehicles can be found as an attachment to this message. This list must be used to identify affected vehicles until they are available via the Key Reader, ISPA or DCS Inquiry.
Associated Products (8)Associated Documents - November 1, 2013•Document ID: 10054629Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- SIM-12-01-13
- Date Added:
- February 11, 2014
- Manufacturer:
- MINI
SummaryMINI: DUE TO AN UNFAVORABLE KNOCK SENSOR, DURING THE WINTER MONTHS, IN AREAS OF EXTREME COLD CLIMATE CONDITIONS, THE SERVICE ENGINE SOON LAMP WILL ILLUMINATE, WHILE ENGINE IS INCREASING TO FULL TEMPERATURE OPERATION. MODELS R55 COOPER CLUBMAN, R56 COOPER, R57 COOPER CONVERTIBLE, R58 COOPER COUPE, R59 COOPER ROADSTER, R60 COOPER COUNTRYMAN. NO YEARS LISTED. *PE
Associated Products (6)Associated Documents - October 1, 2013•Document ID: 10150309Service Bulletin/Repair InstructionsSEATS
- Mfr Comm. #:
- M520213
- Date Added:
- December 3, 2018
- Manufacturer:
- MINI
SummarySqueaking Noise from Front Seat. A noise may be heard from the front driver's seat back when the customer applies sideways pressure during cornering. CAUSE Surface corrosion on the metal seat back frame can make a squeaking noise when rubbing against the foam rubber padding of the seat back.
Associated Products (15)Associated Documents - October 1, 2013•Document ID: 10150308Service Bulletin/Repair InstructionsLATCHES/LOCKS/LINKAGES
- Mfr Comm. #:
- M510613
- Date Added:
- December 3, 2018
- Manufacturer:
- MINI
SummaryBonnet Lock Difficult to Open or Close. The bonnet lock fails to operate correctly and is difficult to open or close. CAUSE Corrosion in the bonnet lock assembly
Associated Products (9)Associated Documents - October 1, 2013•Document ID: 10150306Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC
- Mfr Comm. #:
- M340113
- Date Added:
- December 3, 2018
- Manufacturer:
- MINI
Summary"Erroneous ""Service due"" Message Though Brake Lining Thickness Sufficient. The CBS data calculated for the remaining distance of the front and/or rear brake pads does not agree with the actual brake pad thickness. The yellow brake lining service due indicator illuminates even though the pad thickness is greater than the minimum wear limit (approximately 3.7 mm); the brake wear sensor has not yet been activated (from a thickness of approx. 4.2 mm). In some cases, the red warning message may already be active. The CBS front/rear brake display is based on a mathematical calculation. Various influences are incorporated into this calculation (for example, vehicle speed, brake pressure, and rotor temperature). Due to changing driving characteristics and/or unfavorable environmental conditions, the calculated remaining distance may differ from actual pad thickness."
Associated Products (9)Associated Documents - October 1, 2013•Document ID: 10150305Service Bulletin/Repair InstructionsWHEELS
- Mfr Comm. #:
- M330112
- Date Added:
- December 3, 2018
- Manufacturer:
- MINI
SummaryAdjusting Rear Camber. Rear camber cannot be adjusted properly. CAUSE Repair instructions not followed properly
Associated Products (16)2014 MINI Clubman2014 MINI Cooper2014 MINI Countryman2013 MINI Clubman2013 MINI Cooper2013 MINI Cooper Coupe2013 MINI Cooper Roadster2012 MINI Cooper2012 MINI Cooper Coupe2012 MINI Cooper Roadster2011 MINI Cooper2010 MINI Cooper2009 MINI Cooper2009 MINI Cooper Convertible2008 MINI Cooper2007 MINI CooperAssociated Documents - September 1, 2013•Document ID: 10152363Service Bulletin/Repair InstructionsLATCHES/LOCKS/LINKAGES
- Mfr Comm. #:
- M540313
- Date Added:
- December 17, 2018
- Manufacturer:
- MINI
SummaryConvertible Top Cannot Be Locked or Secured when Fully Opened or Closed. The convertible top cannot be locked or secured when it is in the fully opened or closed position. CAUSE Folding sunroof drive unit hardware error
Associated Products (3)Associated Documents - August 1, 2013•Document ID: 10150241Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- M840213
- Date Added:
- December 3, 2018
- Manufacturer:
- MINI
SummaryIncorrect Customer Relations Telephone Number Is Saved in the Vehicle. The customer is not connected to MINI Customer Relations after dialing the number displayed in the vehicle Kombi or radio. CAUSE During the Pre-Delivery Inspection (PDI), the incorrect telephone number is being written into the vehicle. INFORMATION 1. When performing the PDI test plan, it is extremely important that you select MINI if the ISID is configured for both BMW and MINI. 2. After completion of the PDI test plan, verify that the customer relations number stored in the vehicle is correct. 3. The correct customer relations phone number is 1(866) 275-6464. 4. If the number stored in the vehicle is incorrect and the correct test plan was used, contact your 3g Administrator and have him or her verify the number stored in the ISID. 5.This picture shows the correct number stored in the Combox control unit. Note: To read out telephone number:
Associated Products (16)2014 MINI Clubman2014 MINI Cooper2014 MINI Countryman2013 MINI Clubman2013 MINI Cooper2013 MINI Cooper Coupe2013 MINI Cooper Roadster2012 MINI Cooper2012 MINI Cooper Coupe2012 MINI Cooper Roadster2011 MINI Cooper2010 MINI Cooper2009 MINI Cooper2009 MINI Cooper Convertible2008 MINI Cooper2007 MINI CooperAssociated Documents - August 1, 2013•Document ID: 10150239Service Bulletin/Repair InstructionsSERVICE BRAKES
- Mfr Comm. #:
- M340313
- Date Added:
- December 3, 2018
- Manufacturer:
- MINI
SummaryBrake Fluid Maintenance Service: 36-Month Interval. The CBS displays the first brake fluid service as a 36-month interval from the date of production, instead of the appropriate 24-month interval.
Associated Products (4)Associated Documents - August 1, 2013•Document ID: 10150238Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- M130113
- Date Added:
- December 3, 2018
- Manufacturer:
- MINI
Summary"N14 and N18 Engine: High-pressure Pump Repair Instruction. INFORMATION The current version of ISTA/D Repair Instruction 13 51 017, ""Removing and installing or replacing high-pressure pump (N14, N18)"" has a procedure error. The current version of the Repair Instruction states to replace the highpressure supply hose on the N14 engine. The Repair Instruction also states not to replace the high-pressure supply hose on the N18 engine. The N18 portion of the Repair Instruction is incorrect. As an interim solution, follow the procedure outlined below until this portion of the Repair Instruction is corrected. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15601.2.M130113... 8/30/2013 Page 2 of 2 All vehicles equipped with the N18 engine and produced from 3/2012 and later. When the engine is fitted with a Bosch High-pressure Pump (1) the highpressure supply hose (2) MUST NOT be replaced when making repairs. The remaining portion of the Repair Instruction and tightning torques are correct. Refer to EPC for the applicable part numbers when making repairs. "
Associated Products (15)Associated Documents - August 1, 2013•Document ID: 10150237Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- M120313
- Date Added:
- December 3, 2018
- Manufacturer:
- MINI
Summary?N18 Engine: FC 2BF2 Rail Pressure Sensor Is Stored in DME Fault Memory. The customer states that the Service Engine Soon lamp is illuminated and the following fault is stored in the DME: FC 2BF2 Rail pressure sensor, workspace: pressure too high CAUSE A DME calibration error in the fuel pressure diagnostics results in an increased sensitivity.
Associated Products (16)2014 MINI Clubman2014 MINI Cooper2014 MINI Countryman2013 MINI Clubman2013 MINI Cooper2013 MINI Cooper Coupe2013 MINI Cooper Roadster2012 MINI Cooper2012 MINI Cooper Coupe2012 MINI Cooper Roadster2011 MINI Cooper2010 MINI Cooper2009 MINI Cooper2009 MINI Cooper Convertible2008 MINI Cooper2007 MINI CooperAssociated Documents - August 1, 2013•Document ID: 10053607Service Bulletin/Repair InstructionsENGINE; ENGINE AND ENGINE COOLING
- Mfr Comm. #:
- SI M-12-03-13
- Date Added:
- November 12, 2013
- Manufacturer:
- MINI
SummaryMINI: SOME VEHICLES WOULD EXPERIENCE SERVICE ENGINE SOON LAMP ILLUMINATION OF RAIL PRESSURE SENSOR. MODELS 2012 AND UP R55, 56, 57, 58, 59, 60, 61. *PE
Associated Products (6)Associated Documents - August 1, 2013•Document ID: 10053604Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
- Mfr Comm. #:
- SI-M-13-01-13
- Date Added:
- November 12, 2013
- Manufacturer:
- MINI
SummaryMINI: THERE IS A PROCEDURAL ERROR IN THE REMOVING AND INSTALLING OR REPLACING HIGH PRESSURE PUMP CURRENT VERSION THAT HAS BEEN REPLACED WITH THE CORRECTED REPAIR INSTRUCTION PORTION FOR THE N14 AND N18 ENGINE. MODELS R55, 56, 57, 58, 59, 60, 61. NO MODEL YEARS LISTED. *PE
Associated Products (22)2013 MINI Cooper2013 MINI Cooper Coupe2013 MINI Cooper Roadster2012 MINI Cooper2012 MINI Cooper Coupe2012 MINI Cooper Roadster2011 MINI Cooper2010 MINI Cooper2009 MINI Cooper2009 MINI Cooper Convertible2008 MINI Cooper2008 MINI Cooper Convertible2007 MINI Cooper2007 MINI Cooper Convertible2006 MINI Cooper2006 MINI Cooper Convertible2005 MINI Cooper2005 MINI Cooper Convertible2004 MINI Cooper2003 MINI Cooper+ 2 moreAssociated Documents - July 1, 2013•Document ID: 10150269Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- M620113
- Date Added:
- December 3, 2018
- Manufacturer:
- MINI
SummaryIntermittent Humming or Buzzing Noise from Speedometer. When the vehicle is decelerating, an intermittent humming or buzzing noise coming from the instrument cluster may be heard when the speedometer needle is between 0 and 12 mph. Hardware error in the instrument cluster
Associated Products (9)Associated Documents