Mercedes-Benz G-Class Service Bulletins (2013)

103 manufacturer communications on file.

• September 22, 2026•Document ID: 11038186

  Service Bulletin/Repair Instructions
  SERVICE BRAKES

  Mfr Comm. #:

  LI42.10-P-078779

  Date Added:

  October 6, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

  Associated Products (296)

  2027 Mercedes-Benz C-Class2027 Mercedes-Benz CLA-Class2027 Mercedes-Benz CLE2027 Mercedes-Benz E-Class2027 Mercedes-Benz G-Class2027 Mercedes-Benz GLC-Class2027 Mercedes-Benz GLE-Class2027 Mercedes-Benz S-Class2027 Mercedes-Benz SL-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz G-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class+ 276 more
  Associated Documents

  • DownloadMC-11038186-0001.pdf↗
• September 14, 2026•Document ID: 11038217

  Service Bulletin/Repair Instructions
  STRUCTURE:BODY

  Mfr Comm. #:

  LI82.62-P-078631

  Date Added:

  October 6, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10‑P‑067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

  Associated Products (296)

  2027 Mercedes-Benz C-Class2027 Mercedes-Benz CLA-Class2027 Mercedes-Benz CLE2027 Mercedes-Benz E-Class2027 Mercedes-Benz G-Class2027 Mercedes-Benz GLC-Class2027 Mercedes-Benz GLE-Class2027 Mercedes-Benz S-Class2027 Mercedes-Benz SL-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz G-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class+ 276 more
  Associated Documents

  • DownloadMC-11038217-0001.pdf↗
• September 1, 2026•Document ID: 11037487

  Service Bulletin/Repair Instructions
  SERVICE BRAKES

  Mfr Comm. #:

  LI42.10-P-063502

  Date Added:

  September 25, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy The intent of this document is to reduce noise from high performance AMG brakes. AMG brakes are designed for performance under high load and in certain scenarios, can emit noise. Some scenarios are normal and some are induced by driving style like those listed below: • Driving style such as two footed driving where the pad might be in constant contact with the rotor. • Brake pressure and application style (stop‑and‑go traffic with consistent light brake pressure “riding brakes” where the brakes cannot cool sufficiently between applications). This can cause the brake pads to glaze and have a smooth/glassy surface which can induce noise. • When ambient temperatures rise during summer peak and during cooling and cold winter months. 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3‑4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re‑assessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. Continue with applying chamfer and Molykote as instructed below. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! a) If the noises are coming from the front axle. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining backing plate, including the brake lining guide pins and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston‑side brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". 4. Be sure to remove both brown paper backing sides of the adhesive film, it is double sided adhesive film. 5. If adhesive is already installed on backing plate where pistons contact the back of the pad, you may gently scrape off and re‑apply a new adhesive or Molykote. Must not apply the Molykote on top of the adhesive. 6. Chamfer edges (gently round off sharp leading edges) on brake pads. Some pads have vertical grooves, these can be gently chamfered with a triangular file as well. See picture "Chamfering Technique". 7. Apply Molykote to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 8. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle. 1. Remove brake pads of rear axle. 2. Clean all contact points on brake lining backing plate and brake caliper /carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston‑side brake lining. 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfering Technique". 5. Grease contact points (red areas on attachment "Rear Pad Grease Area") between brake lining and guide of brake caliper with Molykote. 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off

  Associated Products (155)

  2027 Mercedes-Benz SL-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT+ 135 more
  Associated Documents

  • DownloadMC-11037487-0001.pdf↗
• August 26, 2026•Document ID: 11036607

  Service Bulletin/Repair Instructions
  BACK OVER PREVENTION: WARNINGS; FORWARD COLLISION AVOIDANCE: WARNINGS

  Mfr Comm. #:

  LI54.70-P-080191

  Date Added:

  September 2, 2026

  Manufacturer:

  MERCEDES BENZ

  Summary

  Complaint Consistently reproducible erroneous parktronic warnings from front with every key cycle. Cause The parking sensors are detecting the front brush guard. Remedy Complaint must be consistently reproducible and can occur multiple times a key cycle without obvious cause. NOTE: The parking system serves solely as an aid. Please review both the system function and system limitations as shown in the Operator's Manual. Certain environmental factors can affect system functionality such as hot exhaust gases or extreme heat, sensor interference, or other outside influences or aftermarket modifications. If after verifying the complaint is consistently reproducible: 1. Determine if the complaint is reproducible only in high ambient temperatures. If complaint does not occur in cooler ambient temperatures, it is due to system limitations. You may proceed with the below work but the vehicle may be released afterwards as it is due to system limitations. 2. Remove the brush guard and verify the park distance sensors function as expected. 3. Reinstall brush guard and adjust so that it is as far away from the park sensors as possible. This typically means moving the bar further away at the bottom and closer at the top. 4. Check function. If the concern is still consistently reproducible, please apply clear matte film to the locations as shown below at a minimum, although the clear matte film may be applied to the whole brush guard. Picture: Above shown is the 465 brush guard variant. Although similar to the 463, there are some key differences such as the 465 being fitted with a front camera.

  Associated Products (14)

  2026 Mercedes-Benz G-Class2025 Mercedes-Benz G-Class2024 Mercedes-Benz G-Class2023 Mercedes-Benz G-Class2022 Mercedes-Benz G-Class2021 Mercedes-Benz G-Class2020 Mercedes-Benz G-Class2019 Mercedes-Benz G-Class2018 Mercedes-Benz G-Class2017 Mercedes-Benz G-Class2016 Mercedes-Benz G-Class2015 Mercedes-Benz G-Class2014 Mercedes-Benz G-Class2013 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11036607-0001.pdf↗
• August 12, 2026•Document ID: 11036142

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.65-P-080132

  Date Added:

  August 12, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics. Cause Various root causes Remedy See attached diagnostic guide.

  Associated Products (119)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz G-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class+ 99 more
  Associated Documents

  • DownloadMC-11036142-0001.pdf↗
• August 6, 2026•Document ID: 11036190

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.85-P-079087

  Date Added:

  August 14, 2026

  Manufacturer:

  MERCEDES-MAYBACH

  Summary

  Complaint A popup is seen on the HU with the message "data connection temporarily not available". Potentially affected functionalities in NTG4.5, NTG5 1.Weather 2.Local Search 3.IP Radio 4.Send2Car 5.Speech Detection Service 6.Navigation 7.iHeartRadio 8.Traffic Cams Cause MB Apps is sundowned for all vehicles with NTG4.5 and NTG5 Head Unit Variant. Remedy No support available for NTG4.5 and NTG5 Head Unit Variants for MB App related topics. Note: Please do not create TIPS. Please do not replace any components. HU/Hermes SW update / SCN coding will not fix the issue.

  Associated Products (92)

  2024 Mercedes-Benz G-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLC-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz G-Class2022 Mercedes-Benz GLC-Class2021 Mercedes-Benz C-Class2021 Mercedes-Benz E-Class2021 Mercedes-Benz G-Class2021 Mercedes-Benz GLC-Class2020 Mercedes-Benz C-Class2020 Mercedes-Benz E-Class2020 Mercedes-Benz G-Class2020 Mercedes-Benz GLA-Class2020 Mercedes-Benz GLC-Class2020 Mercedes-Benz S-Class2019 Mercedes-Benz C-Class+ 72 more
  Associated Documents

  • DownloadMC-11036190-0001.pdf↗
• August 6, 2026•Document ID: 11036101

  Service Bulletin/Repair Instructions
  STRUCTURE:BODY

  Mfr Comm. #:

  LI82.62-P-078631

  Date Added:

  August 11, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

  Associated Products (287)

  2027 Mercedes-Benz CLA-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class+ 267 more
  Associated Documents

  • DownloadMC-11036101-0001.pdf↗
• July 21, 2026•Document ID: 11035219

  Service Bulletin/Repair Instructions
  BACK OVER PREVENTION: WARNINGS; STRUCTURE:BODY

  Mfr Comm. #:

  LI54.70-P-080191

  Date Added:

  July 24, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Consistently reproducible erroneous parktronic warnings from front with every key cycle. Cause The parking sensors are detecting the front brush guard. Remedy Complaint must be consistently reproducible and can occur multiple times a key cycle without obvious cause. NOTE: The parking system serves solely as an aid. Please review both the system function and system limitations as shown in the Operator's Manual. Certain environmental factors can affect system functionality such as hot exhaust gases or extreme heat, sensor interference, or other outside influences or aftermarket modifications. If after verifying the complaint is consistently reproducible: 1. Determine if the complaint is reproducible only in high ambient temperatures. If complaint does not occur in cooler ambient temperatures, it is due to system limitations. You may proceed with the below work but the vehicle may be released afterwards as it is due to system limitations. 2. Remove the brush guard and verify the park distance sensors function as expected. 3. Reinstall brush guard and adjust so that it is as far away from the park sensors as possible. Typically only small adjustments are possible. 4. Check function. If the concern is still consistently reproducible, please apply clear matte film to the locations as shown below at a minimum, although the clear matte film may be applied to the whole brush guard. Picture: Above shown is the 465 brush guard variant. Although similar to the 463, there are some key differences such as the 465 being fitted with a front camera.

  Associated Products (16)

  2024 Mercedes-Benz G-Class2023 Mercedes-Benz G-Class2022 Mercedes-Benz G-Class2021 Mercedes-Benz G-Class2020 Mercedes-Benz G-Class2019 Mercedes-Benz G-Class2018 Mercedes-Benz G-Class2017 Mercedes-Benz G-Class2016 Mercedes-Benz G-Class2015 Mercedes-Benz G-Class2014 Mercedes-Benz G-Class2013 Mercedes-Benz G-Class2011 Mercedes-Benz G-Class2010 Mercedes-Benz G-Class2004 Mercedes-Benz G-Class2003 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11035219-0001.pdf↗
• July 14, 2026•Document ID: 11035118

  Service Bulletin/Repair Instructions
  BACK OVER PREVENTION: WARNINGS; STRUCTURE:BODY

  Mfr Comm. #:

  LI54.70-P-080191

  Date Added:

  July 21, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Consistently reproducible erroneous parktronic warnings from front with every key cycle. Cause The parking sensors are detecting the front brush guard. Remedy Complaint must be consistently reproducible and can occur multiple times a key cycle without obvious cause. NOTE: The parking system serves solely as an aid. Please review both the system function and system limitations as shown in the Operator's Manual. Certain environmental factors can affect system functionality such as hot exhaust gases or extreme heat, sensor interference, or other outside influences or aftermarket modifications. If after verifying the complaint is consistently reproducible: 1. Determine if the complaint is reproducible only in high ambient temperatures. If complaint does not occur in cooler ambient temperatures, it is due to system limitations. You may proceed with the below work but the vehicle may be released afterwards as it is due to system limitations. 2. Remove the brush guard and verify the park distance sensors function as expected. 3. Reinstall brush guard and adjust so that it is as far away from the park sensors as possible. Typically only small adjustments are possible. 4. Check function. If the concern is still consistently reproducible, please apply clear matte film to the locations as shown below at a minimum, although the clear matte film may be applied to the whole brush guard.

  Associated Products (14)

  2024 Mercedes-Benz G-Class2023 Mercedes-Benz G-Class2022 Mercedes-Benz G-Class2021 Mercedes-Benz G-Class2020 Mercedes-Benz G-Class2019 Mercedes-Benz G-Class2018 Mercedes-Benz G-Class2017 Mercedes-Benz G-Class2016 Mercedes-Benz G-Class2015 Mercedes-Benz G-Class2014 Mercedes-Benz G-Class2013 Mercedes-Benz G-Class2011 Mercedes-Benz G-Class2010 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11035118-0001.pdf↗
• July 14, 2026•Document ID: 11035005

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI35.30-P-058566

  Date Added:

  July 14, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

  Associated Products (287)

  2027 Mercedes-Benz CLA-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class+ 267 more
  Associated Documents

  • DownloadMC-11035005-0001.pdf↗
• June 17, 2026•Document ID: 11033981

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM; BACK OVER PREVENTION: WARNINGS

  Mfr Comm. #:

  LI54.70-P-080191

  Date Added:

  June 18, 2026

  Manufacturer:

  MERCEDES BENZ

  Summary

  Complaint Consistently reproducible erroneous parktronic warnings from front with every key cycle. Cause The parking sensors are detecting the front brush guard. Remedy Complaint must be consistently reproducible and can occur multiple times a key cycle without obvious cause. NOTE: The parking system serves solely as an aid. Please review both the system function and system limitations as shown in the Operator's Manual. Certain environmental factors can affect system functionality such as hot exhaust gases or extreme heat, sensor interference, or other outside influences or aftermarket modifications. If after verifying the complaint is consistently reproducible: 1. Remove the brush guard and verify the park distance sensors function as expected. 2. Reinstall brush guard and adjust so that it is as far away from the park sensors as possible. Typically only small adjustments are possible. 3. Check function. If the concern is still consistently reproducible, please apply clear matte film to the locations as shown below at a minimum, although the clear matte film may be applied to the whole brush guard.

  Associated Products (17)

  2025 Mercedes-Benz G-Class2024 Mercedes-Benz G-Class2023 Mercedes-Benz G-Class2022 Mercedes-Benz G-Class2021 Mercedes-Benz G-Class2020 Mercedes-Benz G-Class2019 Mercedes-Benz G-Class2018 Mercedes-Benz G-Class2017 Mercedes-Benz G-Class2016 Mercedes-Benz G-Class2015 Mercedes-Benz G-Class2014 Mercedes-Benz G-Class2013 Mercedes-Benz G-Class2011 Mercedes-Benz G-Class2010 Mercedes-Benz G-Class2004 Mercedes-Benz G-Class2003 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11033981-0001.pdf↗
• June 12, 2026•Document ID: 11033855

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI00.20-P-080703

  Date Added:

  June 16, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Service code B1 displayed in the customer menu does not match the workshop code displayed in the workshop menu, e.g., 505 or 550A, which includes a service A. Cause The root cause is currently being investigated. Remedy To determine the cause, the instrument cluster control unit (N133/1) and powertrain control unit (N127) logs are required before confirming the service or correction using XENTRY Diagnosis. Please open a TIPS case to BCE inbox with the requested information in the attachments.

  Associated Products (97)

  2027 Mercedes-Benz CLA-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class+ 77 more
  Associated Documents

  • DownloadMC-11033855-0001.pdf↗
• May 26, 2026•Document ID: 11033185

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.85-P-080507

  Date Added:

  June 2, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint After successful commissioning of the HERMES control unit (N112/9) with XENTRY Diagnosis DVD 03/2026, the message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: • HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) • Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommission the HERMES control unit (N112/9) with XENTRY Diagnosis 03/2026 and add-on 33399 installed or carry out the procedure with a newer version of XENTRY Diagnosis: XENTRY→ "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

  Associated Products (175)

  2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class+ 155 more
  Associated Documents

  • DownloadMC-11033185-0001.pdf↗
• May 15, 2026•Document ID: 11032702

  Service Bulletin/Repair Instructions
  SERVICE BRAKES

  Mfr Comm. #:

  LI42.10-P-078779

  Date Added:

  May 15, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. Vehicle production date prior to December 2025. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

  Associated Products (32)

  2026 Mercedes-Benz GLS-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2022 Mercedes-Benz G-Class2022 Mercedes-Benz GLE-Class2022 Mercedes-Benz GLS-Class2021 Mercedes-Benz G-Class2021 Mercedes-Benz GLE-Class2021 Mercedes-Benz GLS-Class2020 Mercedes-Benz G-Class2020 Mercedes-Benz GLE-Class2020 Mercedes-Benz GLS-Class2019 Mercedes-Benz G-Class2019 Mercedes-Benz GLE-Class+ 12 more
  Associated Documents

  • DownloadMC-11032702-0001.pdf↗
• May 12, 2026•Document ID: 11032699

  Service Bulletin/Repair Instructions
  BACK OVER PREVENTION: WARNINGS; LANE DEPARTURE: BLIND SPOT DETECTION; ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.65-P-080132

  Date Added:

  May 14, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

  Associated Products (117)

  2027 Mercedes-Benz CLA-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class+ 97 more
  Associated Documents

  • DownloadMC-11032699-0001.pdf↗
• May 7, 2026•Document ID: 11032586

  Service Bulletin/Repair Instructions
  STRUCTURE:BODY

  Mfr Comm. #:

  LI88.80-P-080031

  Date Added:

  May 11, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Water ingress in the load compartment between the C and D pillars. Cause In the area of the rounding at the D-pillar, a leakage may occur between the rear side wall and the roof paneling. Remedy Troubleshooting: Locate the area of the leak by performing a pressure test and using leak detector spray or soapy water. To do this, tape up the rear vents on the D-pillars and set the ventilation system to the maximum blower setting. If leaks are verified, proceed with sealing of the drip rail: 1. Remove the corner seal strip of the drip rail (see AR88.80-P-4005XG). 2. Clean and apply primer to the marked areas (see figure 1). 3. Replace the corner seal strip and fill with sealant, then mount it straight onto the flange. 4. Remove any excess adhesive and Install outer drip rail. Apply adhesive to inside corner. 5. After installing the drip rails, perform a water test (approx. 0.5 hours).

  Associated Products (16)

  2024 Mercedes-Benz G-Class2023 Mercedes-Benz G-Class2022 Mercedes-Benz G-Class2021 Mercedes-Benz G-Class2020 Mercedes-Benz G-Class2019 Mercedes-Benz G-Class2018 Mercedes-Benz G-Class2017 Mercedes-Benz G-Class2016 Mercedes-Benz G-Class2015 Mercedes-Benz G-Class2014 Mercedes-Benz G-Class2013 Mercedes-Benz G-Class2011 Mercedes-Benz G-Class2010 Mercedes-Benz G-Class2004 Mercedes-Benz G-Class2003 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11032586-0001.pdf↗
• April 24, 2026•Document ID: 11031558

  Service Bulletin/Repair Instructions
  UNKNOWN OR OTHER

  Mfr Comm. #:

  LI00.01-P-078887

  Date Added:

  April 25, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint The intent of this document is to provide workshops with helpful technical reference language. • Commonly used acronyms in LI's and TIPS cases. • Control unit names, numbers, and how to identify. • Network/wiring architecture groups to baumuster quick reference. • Platform to baumuster quick reference. Cause Information only Remedy Acronyms: • AV = Actual Values • CPR = Car Package Release (For MB.OS) • CU = Control Unit • CUL = Control Unit Log • DTC = Diagnostic Trouble Code • E-Stand = Fresh-up head unit boot software (found in head unit control unit log) • FUP = Fresh-up • FW = Firmware • HSVL = High Speed Video Line • HU = Head Unit • HW = Hardware • IPD = Injector Performance Data • ISU = Initial Start Up • LVDS = Low Voltage Differential Signal • NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) • NSFT = Not Safe For Transport • MOPF = Model Facelift (Ex: 167 MOPF) • PiH = Plug-in Hybrid • SA Code = Sonderausstattungscode (Option Code) • SCN = Software Calibration Number • SW = Software • TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) • QT = Quicktest • XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. • Control Unit Name • Control Unit Number • Control Unit Short name • Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 • 117, 156, 246 (MFA) • 166, 176, 221, 242, 246, 292 • 906 Star 2 • 205, 213, 238, 253, 257, 290 (MRA) • 117, 156, 246 (MFA) • 118, 177, 243, 247 (MFA2) • 167, 222, 292, 463, 465 • 907 Star 3 • 294, 295, 296, 297 (EVA2) • 206, 214, 223, 236, 254 (MRA2) • 192 and 232 (MSA) Star 3.5 • 174 • 178 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": • 205 • 213 • 222 • 238 • 253 • 257 • 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": • 206 • 214 • 223 • 236 • 254 MFA = "Mercedes-Benz Frontwheel Architecture" • 117 • 156 • 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" • 118 • 177 • 243 • 247 EVA1.5 = "Electric Vehicle Architecture" • 243 EVA2 = "Electric Vehicle Architecture - Generation 2" • 294 • 295 • 296 • 297 MSA = "Mercedes-Benz Sport Architecture" • 192 • 232 MMA = "Mercedes-Benz Modular Architecture" • 174 • 178

  Associated Products (109)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class+ 89 more
  Associated Documents

  • DownloadMC-11031558-0001.pdf↗
• April 20, 2026•Document ID: 11031582

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.85-P-080507

  Date Added:

  April 27, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint After successful commissioning of the HERMES control unit (N112/9) with XENTRY Diagnosis DVD 03/2026, the message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: • HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) • Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommissioning of the HERMES control unit (N112/9) using XENTRY Diagnosis version 12/2025. This is mandatory: XENTRY→ "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

  Associated Products (17)

  2025 Mercedes-Benz G-Class2024 Mercedes-Benz G-Class2023 Mercedes-Benz G-Class2022 Mercedes-Benz G-Class2021 Mercedes-Benz G-Class2020 Mercedes-Benz G-Class2019 Mercedes-Benz G-Class2018 Mercedes-Benz G-Class2017 Mercedes-Benz G-Class2016 Mercedes-Benz G-Class2015 Mercedes-Benz G-Class2014 Mercedes-Benz G-Class2013 Mercedes-Benz G-Class2011 Mercedes-Benz G-Class2010 Mercedes-Benz G-Class2004 Mercedes-Benz G-Class2003 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11031582-0001.pdf↗
• April 16, 2026•Document ID: 11031580

  Service Bulletin/Repair Instructions
  EXTERIOR LIGHTING

  Mfr Comm. #:

  LI82.10-P-078301

  Date Added:

  April 27, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

  Associated Products (285)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class+ 265 more
  Associated Documents

  • DownloadMC-11031580-0001.pdf↗
• April 3, 2026•Document ID: 11031825

  Other
  STRUCTURE:BODY; EXTERIOR LIGHTING

  Mfr Comm. #:

  PSL- NCU Return Parts 4/3

  Date Added:

  May 1, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  The part numbers listed in the chart below should no longer be installed, and any existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, April 23, 2026. After April 23rd, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

  Associated Products (17)

  2026 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLE-Class2022 Mercedes-Benz GLE-Class2021 Mercedes-Benz GLE-Class2020 Mercedes-Benz GLE-Class2018 Mercedes-Benz G-Class2017 Mercedes-Benz G-Class2016 Mercedes-Benz G-Class2015 Mercedes-Benz G-Class2014 Mercedes-Benz G-Class2013 Mercedes-Benz G-Class2011 Mercedes-Benz G-Class2010 Mercedes-Benz G-Class2004 Mercedes-Benz G-Class2003 Mercedes-Benz G-Class
  Associated Documents

  • DownloadMC-11031825-0001.pdf↗