Ford Motor Company (Ford) is recalling certain 2013-2019 Escape, 2013-2018 C-Max, 2013-2016 Fusion, 2013-2021 Transit Connect, and 2015-2018 Edge vehicles. The bushing that attaches the shifter cable to the transmission may degrade or detach.
Ford Motor Company (Ford) is recalling certain 2011-2014 Fiesta, 2013-2014 Fusion, 2015 Mustang, 2013-2015 Escape and C-Max, 2012-2015 Focus, 2014-2016 Transit Connect, 2013-2014 Lincoln MKZ, and 2015 MKC vehicles. These vehicles were previously recalled and repaired under recalls 15V-246, 16V-643 or 17V-210, however the repair may not have been completed properly. A component within the door latches may break making the doors difficult to latch and/or leading the driver or a passenger to believe a door is securely closed when, in fact, it is not.
Ford Motor Company (Ford) is recalling certain 120V Convenience charge cords that were supplied with and sold for use with 2013-2015 Ford C-Max Energi and Fusion Energi vehicles and 2012-2015 Ford Focus Electric vehicles. Cords with part numbers FM58-10B706-AA, FM58-10B706-AB, FM58-10B706-AC, FM58-10B706-AD, FM58-10B706-AE and FM58-10B706-AF were manufactured without thermistors, and during vehicle charging, increased resistance in the house's outlet or wiring can cause the cord to overheat and melt.
Ford Motor Company (Ford) is recalling certain model year 2012-2015 Ford Focus, 2013-2015 Ford Escape and Ford C-MAX, 2015 Lincoln MKC and Ford Mustang, and 2014-2016 Ford Transit Connect vehicles. A component within the door latches may break, preventing the doors from latching and/or leading the driver or a passenger to believe a door is securely closed when, in fact, it is not.
Ford Motor Company (Ford) is recalling certain model year 2013-2014 Ford C-Max vehicles manufactured January 19, 2012, to November 21, 2013; Ford Fusion vehicles manufactured February 3, 2012, to August 24, 2013; Ford Escape vehicles manufactured October 5, 2011, to November 1, 2013; and Lincoln MKZ vehicles manufactured April 25, 2012, to September 30, 2013. The coating on portions of the Restraint Control Module (RCM) may crack, and when exposed to humidity, circuits on the printed circuit board may short.
Summary of Safety Issue The vehicle repeatedly experiences sudden loss of propulsion while driving, accompanied by a “Stop Safely Now” warning message and various other dashboard warnings . During these events the accelerator pedal becomes completely unresponsive while the vehicle remains powered, indicating a failure of the hybrid propulsion system or high-voltage battery control system. The vehicle and video footage of the failure are available for inspection upon request. Timeline of Events January 13, 2026 – The vehicle displayed a “Stop Safely Now” warning message and lost the ability to accelerate. The vehicle had to be towed to Lehighton Ford. January 21, 2026 – Paid $866.85 for repairs including battery service, Rear Control Module replacement, and PCM harness repair. Lehighton Ford stated the vehicle was repaired and safe to drive. Within minutes of leaving the dealership, the vehicle stalled again in active traffic and had to be returned. The issue was escalated to the Ford Engineering hotline and a Field Service Engineer. February 17, 2026 – The dealership attempted to return the vehicle after performing a BECM reprogramming. Upon pickup, new issues were immediately observed including near-stall conditions and hybrid system malfunction, so the vehicle was left with the dealership again. February 18, 2026 - The owner brought forth concerns about Ford’s Technical Service Bulletin (TSB) 17-0015 which identifies potential damage to the traction battery interlock harness as a root cause for intermittent stalling and "Stop Safely Now" warnings. Although the dealership recorded Diagnostic Trouble Code B11D8—a fault directly related to the stall condition—the dealership later stated that no diagnostic codes relevant to the TSB were present and this component was not inspected. February 20, 2026 - Dealership claims that the vehicle has been test-driven for over 100 miles and is “functioning perfectly” and that a ‘battery rebalance’ was causing the issues experie
No injuries · No fire · No crash
The rear impact bar is completely disintegrated and is falling off of the subframe due to extreme rust. There is either no or very little amount of rust on the entirety of the rest of the vehicle. The impact bar is either manufactured with incorrect materials or is otherwise defective. The impact absorber is attached to the impact bar and due to the integrity of the impact bar being destroyed, the crumple zone in the rear of the vehicle will not work as intended and the safety systems would not perform as intended. The impact absorber is not sitting correctly as attached to the impact bar and major portions of the impact bar are missing due to extreme rust. This is currently available for inspection but is going to be repaired soon. A review of forums, like Reddit, online reveal that other owners of this generation of Cmax have had rusted out impact bars in the rear and have failed state safety inspection. This vehicle was never in an accident.
No injuries · No fire · No crash
Rear view camera display is upside down. Display was normal when the vehicle was purchased and then one day it flipped upside down and all overlay information disappeared (lines and distance indicators).
No injuries · No fire · No crash
I took it to the Ford dealership and they diagnosed it as having a parasitic draw from the 12 V battery when the car is shut down so when you go to get into the car if the battery is dead, they will fix it for $425 however, this problem was a recall in 2013 and my car did have a recall done to it. However, the issue is still going on therefore I feel as though the customer should not be charged. My car broke down going up the canyon and it told me to pull over safely, which I did going up the hill, but it was on an exit and it was a dangerous situation as I could not even turn on my flashers. This has been a known issue with the Ford C max since 2013 and since their software program then did not correct the problem and now they want to update the software why should the cost come from the Consumer?
No injuries · No fire · No crash
The backup camera always quits working while in the middle of reversing. It will work for a second, but then the display will flip upside down or go completely black and display a message saying "Camera unavailable. Please contact your dealership." It started doing this about a year ago, but was intermittent. It started happening more often over time, and now it always happens. It makes reversing dangerous, as the camera will quit working while the vehicle is still moving. This is especially dangerous in parking lots where there are pedestrians around. It is available for inspection upon request. It has not been inspected by anyone yet.
No injuries · No fire · No crash