BMW X5 Service Bulletins
1,651 manufacturer communications on file.
- April 1, 2013•Document ID: 10052618Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- SIB-12-17-12
- Date Added:
- August 22, 2013
- Manufacturer:
- BMW
SummaryBMW: WHEN TRANSMISSION IS IN HIGH GEAR, DUE TO DELAY IN DOWNSHIFTING, THE ENGINE HAS A DELAY RESPONSE AFTER DECELERATING AT LOW SPEEDS AND THEN REACCELERATING. MODELS F25 (X3), F10 (5 SERIES), F07 (5 GT), E70 (X5), E71 (X6). NO MODEL YEARS LISTED. *PE UPDATED 08/05/2014 *JS
Associated Products (3)Associated Documents - March 1, 2013•Document ID: 10150123Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:BRAKE LIGHTS; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 631009
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryINFORMATION Note: Failures that result from the installation of non-approved accessories and/or non-original parts are not covered. Procedure A with Reprogramming and Encoding the Vehicle Covered under the terms of the BMW New Vehicle/SAV Limited Warranty or the BMW Certified Pre-Owned Program. Labor operation code 00 00 006 is a Main labor operation. If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead. If a control module fails to program correctly or initializations are required, the additional work must be claimed with separate labor operations under the applicable defect code listed above; refer to KSD2. And, if necessary, also: Procedure A without Reprogramming and Encoding the Vehicle (Vehicle is already at the Correct I-Level) Covered under the terms of the BMW New Vehicle/SAV Limited Warranty.
Associated Products (11)Associated Documents - March 1, 2013•Document ID: 10150119Service Bulletin/Repair InstructionsVISIBILITY
- Mfr Comm. #:
- 610813
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryFront or Rear Windshield Wipers Fail to Operate. INFORMATION The following troubleshooting hints are based on known areas that can cause the situations described above to occur. 1. Front windshield wiper failure: perform the following checks only when the front windshield wiper fails to operate. If the rear wipers fail to operate, proceed to section 2. * Check Fuse F44 (30 A) and replace as necessary. * Check connector X333 at the front wiper motor to makes sure it is plugged in correctly, and no corrosion exists at the connection. Repair as needed.
Associated Products (14)Associated Documents - March 1, 2013•Document ID: 10150117Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 610513
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryThe vehicle does not start. CAUSE Software error in the CAS (Car Access System).
Associated Products (13)Associated Documents - March 1, 2013•Document ID: 10150116Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 610512
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryBattery Discharged Because of Unfavorable Driving Profile. In certain situations, the battery may become discharged when the vehicle is driven frequently on short trips (less than 3 miles per trip), or when the telephone or entertainment system is used for up to 30 minutes while the vehicle is stationary. CAUSE The vehicle charging system, in extreme conditions, is not able to properly compensate for the excessive discharging of the battery caused by an unfavorable driving profile.
Associated Products (14)Associated Documents - March 1, 2013•Document ID: 10150107Service Bulletin/Repair InstructionsSTEERING; SUSPENSION
- Mfr Comm. #:
- 320210
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"Squeaking Noises from Steering Wheel While Turning. There is a squeaking noise from the steering column when the steering wheel is turned. The rubber boot on the steering column is not positioned correctly or lacks sufficient grease for the plastic bearing. INFORMATION The problem has been integrated into ISTA diagnostics. Follow the diagnosis test plan, using the latest ISTA version. In ""Information Search,"" select the ""Function Structure"" tab. Select ""Chassis and Suspension / Steering / Steering interference noise,"" and then press ""Start Search."" Select test plan ""AM3201_00222 - Steering noises."" The BMW Group has integrated NED (Non-electric Diagnosis) into diagnosis for the purpose of finding the cause of mechanical, acoustic and visual problems. Refer to bulletin B07 03 10 for more details."
Associated Products (14)Associated Documents - March 1, 2013•Document ID: 10150106Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- 240113
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryOil Leak from Transfer Case. Oil is leaking from the transmission area, or oil seepage is noticed from the transmission/transfer case area during a service. CAUSE The leak can be misdiagnosed as a transmission fluid leak from either the mechatronics sleeve or transmission oil pan. The leak is actually coming from the transfer case (input or output shaft seal).
Associated Products (18)Associated Documents - March 1, 2013•Document ID: 10150105Service Bulletin/Repair InstructionsFUEL SYSTEM, DIESEL; ENGINE
- Mfr Comm. #:
- 180612
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"Voluntary Emissions Recall Campaign 11E-A03: Replace the SCR Mixer. The Selective Catalyst Reduction (SCR) mixer has also been improved to optimize the Diesel Exhaust Fluid (DEF) mixture when introduced into the exhaust system. AFFECTED VEHICLES This Emissions Recall Campaign involves X5d and 335d models that were produced from February 2010 to September 2010. In order to determine whether a specific vehicle has had this Emissions Recall Campaign completed or is affected by this Emissions Recall Campaign, first check if the ""Emissions Recall Campaign Completed"" label SD 92-435 is attached to the right (passenger) rear side of the hood in the engine compartment, close to the windshield. If the label is found, the campaign has already been performed. If the ""Emissions Recall Campaign Completed"" label is not present, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action."
Associated Products (1)Associated Documents - March 1, 2013•Document ID: 10150104Service Bulletin/Repair InstructionsFUEL SYSTEM, DIESEL; ENGINE
- Mfr Comm. #:
- 180512
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"Voluntary Emissions Recall Campaign 11E-A03: Check and/or Replace Emissions Monitoring Components. 1. Under certain driving conditions, the High-pressure (HP) EGR valve may become restricted with excessive soot. This restriction impedes the emissions performance of the HP EGR valve. This situation may lead to a Service Engine Soon lamp. An optimized EGR valve has been developed to limit this soot buildup. 2. The Selective Catalyst Reduction (SCR) mixer has also been improved to optimize the Diesel Exhaust Fluid (DEF) mixture when introduced into the exhaust system. Note: These Improved parts may have already been replaced during a previous service visit. It will be necessary to inspect these components first before replacement. 3. Reprogramming of the DDE is required to optimize these improved emissions monitoring components. AFFECTED VEHICLES This Emissions Recall Campaign involves X5d (E70) and 335d (E90) models that were produced from April 2009 to March 2011. In order to determine whether a specific vehicle has had this Emissions Recall Campaign completed or is affected by this Emissions Recall Campaign, first check if the ""Emissions Recall Campaign Completed"" label SD 92-435. This label is attached to the right (passenger) rear side of the hood in the engine compartment, close to the windshield. If the label is found, the campaign has already been performed. If the ""Emissions Recall Campaign Completed"" label is not present, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action."
Associated Products (6)Associated Documents - March 1, 2013•Document ID: 10150103Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 180212
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"?Voluntary Emissions Recall Campaign 11E-A03: Check and/or Replace Emissions Monitoring Components. 1. The Selective Catalyst Reduction (SCR) catalyst has been improved to increase emissions stability over the service life of the vehicle. 2. The SCR mixer has also been improved to optimize the Diesel Exhaust Fluid (DEF) mixture when introduced into the exhaust system. 3. Under certain driving conditions, the High-Pressure (HP) EGR valve may become restricted with excessive soot. This restriction impedes the emissions performance of the HP EGR valve. This situation may lead to the Service Engine Soon lamp illuminating. An optimized EGR valve has been developed to limit this soot buildup. Note: These improved parts may have already been replaced during a previous service visit. It will be necessary to inspect these components first before replacement. 4. Reprogramming of the DDE to optimize these improved emissions monitoring components. AFFECTED VEHICLES This Emissions Recall Campaign involves X5d and 335d models that were produced from January 2008 to September 2009. In order to determine whether a specific vehicle has had this Emissions Recall Campaign completed or is affected by this Emissions Recall Campaign, first check if the ""Emissions Recall Campaign Completed"" label SD 92-435 is attached to the right (passenger) rear side of the hood in the engine compartment, close to the windshield. If the label is found, the campaign has already been performed. If the ""Emissions Recall Campaign Completed"" label is not present, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action. If the label is found, the campaign has already been performed. If the ""Emissions Recall Campaign Completed"" label is not present, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or
Associated Products (4)Associated Documents - March 1, 2013•Document ID: 10150101Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE; ENGINE
- Mfr Comm. #:
- 130712
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryN63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
Associated Products (71)Associated Documents - March 1, 2013•Document ID: 10150096Service Bulletin/Repair InstructionsPOWER TRAIN; ENGINE
- Mfr Comm. #:
- 121611
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryN55 Engine Failsafe - FC 120308 Boost Pressure Control, Plausibility: Pressure Too Low Stored in DME Fault Memory. INFORMATION The customer complains the SES is illuminated and the engine has reduced power (engine failsafe mode).
Associated Products (134)Associated Documents - March 1, 2013•Document ID: 10150095Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 110907
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryIntermittent Hydraulic Valve Adjuster (HVA) Noise. An occasional ticking or rattling noise from the camshaft hydraulic valve lifters (HVA) may occur during cold engine starts, due to frequent short-distance driving, or the noise may occur for an extended period of time even though the engine is at operating temperature. Improved parts were phased into production beginning on 10/1/2008 and fully implemented on November 31st 2008.
Associated Products (31)Associated Documents - March 1, 2013•Document ID: 10052012Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:12V/24V/48V BATTERY
- Mfr Comm. #:
- SIB-61-13-05
- Date Added:
- May 1, 2013
- Manufacturer:
- BMW
SummaryBMW: BATTERY HAS AN INCREASED DEMAND DUE TO DEVELOPEMENTAL PROCESS OF THE ELECTRICAL SYSTEM. THIS IS CAUSING THE BATTER TO NEED TO UNDERGO AN ENERGY DIAGNOSIS. *KB
Associated Products (60)Associated Documents - March 1, 2013•Document ID: 10051971Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; ELECTRICAL SYSTEM:12V/24V/48V BATTERY
- Mfr Comm. #:
- SIB-61-05-12
- Date Added:
- April 25, 2013
- Manufacturer:
- BMW
SummaryBMW: BATTER DISCHARGED BECAUSE OF UNFAVORABLE DRIVING PROFILE. THIS IS CAUSED ON SHORT TRIPS (LESS THAN 3 MILES) OR WHEN THE TELEPHONE OR ENTERTAINMENT SYSTEM IS USED FOR UP TO 30 MINUTES WHILE VEHICLE IS STATIONARY. MODELS X5, X6 ALL MODEL YEARS AFFECTED. *KB
Associated Products (29)Associated Documents - March 1, 2013•Document ID: 10046959Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:EXHAUST SYSTEM
- Mfr Comm. #:
- SIB-18-06-12
- Date Added:
- November 2, 2012
- Manufacturer:
- BMW
SummaryBMW: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. WHEN INTRODUCED INTO EXHAUST SYSTEM, SELECTIVE CATALYST REDUCTION (SCR) MIXER WAS IMPROVED TO OPTIMIZE DIESEL EXHAUST FLUID (DEF) MIXTURE. MODEL 2010 E70, E90. *PE UPDATED ON 4/25/2013. *KB
Associated Products (2)Associated Documents - March 1, 2013•Document ID: 10046861Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE)
- Mfr Comm. #:
- SIB-18-02-12
- Date Added:
- November 1, 2012
- Manufacturer:
- BMW
SummaryBMW: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. THE REPLACING AND/OR CHECKING OF EMISSIONS MONITORING COMPONENTS TO INCREASE EMISSIONS STABILITY, HIGH PRESSURE (HP) EGR VALVE RESTRICTION OF EXCESSIVE SOOT AND IMPROVED DIESEL EXHAUST FLUID (DEF) MIXTURE INTRODUCED IN EXHAUST SYSTEM FROM SCR MIXER. MODEL 2008-2009 E70, E90. *PE UPDATED 5/10/13. *PE
Associated Products (3)Associated Documents - March 1, 2013•Document ID: 10045284Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL
- Mfr Comm. #:
- SIB-18-05-12
- Date Added:
- August 28, 2012
- Manufacturer:
- BMW
SummaryBMW: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. UNDER VOLUNTARY EMISSIONS RECALL CAMPAIGN 11E-A03:CHECK/REPLACE EMISSIONS MONITORING COMPONENTS. DUE TO EXCESSIVE SOOT BUILD UP, THE HIGH PRESSURE (HP) EGR VALVE MAY BE RESTRICTED UNDER CERTAIN DRIVING CONDITIONS. *PE UPDATED ON 4/25/2013. *KB
Associated Products (4)Associated Documents - March 1, 2013•Document ID: 10041407Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:ENGINE
- Mfr Comm. #:
- SIB-12-16-11
- Date Added:
- September 30, 2011
- Manufacturer:
- BMW
SummaryBMW: SERVICE ENGINE SOON LIGHT IS ON AND THE ENGINE HAS REDUCED POWER WITH TROUBLE CODES STORED. *RM UPDATED ON 4/24/2013. *KB
Associated Products (23)Associated Documents - March 1, 2013•Document ID: 10040177Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:BRAKE LIGHTS
- Mfr Comm. #:
- SIB-63-10-09
- Date Added:
- August 16, 2011
- Manufacturer:
- BMW
SummaryBMW: THE BRAKE LIGHT FAILS AND THE BULB HOLDER IS DEFORMED DUE TO HIGH TEMPERATURES AND THE COMPOSITION OF THE HOLDER. *RM UPDATED ON 4/25/2013. *KB
Associated Products (16)Associated Documents