Mercedes-Benz G-Class Service Bulletins
325 manufacturer communications on file.
- December 6, 2024•Document ID: 11011781Service CampaignENGINE
- Mfr Comm. #:
- CL-240903
- Date Added:
- December 12, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryMercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year 2021 - 2022 G-Class vehicles, the engine control unit software characteristics may not meet local regulatory requirements for the vehicle's On-Board Diagnostics and/or exhaust gas emissions. Our records indicate that your vehicle is included in the affected population. What is the issue? During low-load operations, the vehicle's air/fuel ratio diagnostic system may not be activated as intended. What will your Mercedes-Benz Dealership do? An authorized Mercedes-Benz dealership will check and, if necessary, update the Engine Control Unit Software. This vehicle repair will be provided at no cost to you. While the minimum repair time can be up to 30 minutes, your dealership can provide you with a better estimate of the overall time for this service visit. As a matter of normal service process, an authorized Mercedes-Benz dealer will also check for other repair measures which might be applicable to your vehicle and this may increase the required working time. You will not be charged for other service or repairs unless so requested. Steps to take. . Find your nearest authorized Mercedes-Benz dealership at mbusa.com/recall to schedule your recall repair. . Please mention you are scheduling an appointment for Mercedes-Benz Emissions Recall Campaign # 2024090003 (CA DMV # 240903) . You may be asked for your VIN, which for your convenience is located at the top of this letter.
Associated Products (2)Associated Documents - December 5, 2024•Document ID: 11011539Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- LI07.61-P-078629
- Date Added:
- December 6, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint After performing a software update either for recall campaign 2023070022 or general course of diagnosis the vehicle will not start and/or the software flash will not complete. Cause Newer software releases are incompatible with older HW object numbers (ME part numbers). Remedy If a no start condition is encountered after a software update, check the ME and VGS control unit part numbers. Open an XSF ticket with the PN's and explain what software is attempting to be flashed. Afterwards continue with the repair as normal and quality check the vehicle. If any issues arise open a TIPS case and forward it to market support.
Associated Products (6)Associated Documents - November 27, 2024•Document ID: 11010970Over The AirELECTRICAL SYSTEM
- Mfr Comm. #:
- OTA - 24P5497813
- Date Added:
- December 3, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryMercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-25 C-Class, CLA, EQB, EQE, EQS, G-Class, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (206, 118, 243, 294, 296, 465, 247, 254, 167, 192, 223, and 232 platform) vehicles, the MBUX multimedia system does not correspond with the latest series production configuration. The MBUX multimedia system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
Associated Products (46)2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class+ 26 moreAssociated Documents - November 23, 2024•Document ID: 11010964EmissionsENGINE
- Mfr Comm. #:
- 2024090003
- Date Added:
- December 3, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryMercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that the software for the engine control unit in the subject vehicles may not meet current specifications. As a result, the diagnosis for monitoring the air fuel ratio might not be activated in low load operation as intended. Consequently, this may not meet local regulatory requirements for on-board diagnostics and/or exhaust gas emissions. An authorized Mercedes-Benz dealer will update the Engine Control Unit software in the affected vehicles.
Associated Products (2)Associated Documents - November 20, 2024•Document ID: 11010818Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- LI27.19-P-072588
- Date Added:
- November 27, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
Associated Products (189)2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLA-Class+ 169 moreAssociated Documents - November 20, 2024•Document ID: 11010755Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- LI82.85-P-078473
- Date Added:
- November 23, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": • The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). • In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": • The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). • In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
Associated Products (147)2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class+ 127 moreAssociated Documents - November 12, 2024•Document ID: 11010455Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- LI27.10-P-075869
- Date Added:
- November 12, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
Associated Products (89)2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz C-Class+ 69 moreAssociated Documents - November 9, 2024•Document ID: 11010440Service CampaignENGINE
- Mfr Comm. #:
- NCU - 2024100016
- Date Added:
- November 12, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryMercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz, has determined that on certain MY 2019-2021 G-Class (463 platform) vehicles, the engine control unit software does not correspond to current production specifications. It is therefore possible that on-board diagnostics and/or exhaust gas emissions requirements may not be fulfilled. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will perform the ECU software update.
Associated Products (3)Associated Documents - October 23, 2024•Document ID: 11009122Service Bulletin/Repair InstructionsSTRUCTURE:BODY; VISIBILITY/WIPER
- Mfr Comm. #:
- LI82.35-P-078467
- Date Added:
- October 25, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
Associated Products (265)2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class+ 245 moreAssociated Documents - October 16, 2024•Document ID: 11009036Service Bulletin/Repair InstructionsWHEELS; ELECTRICAL SYSTEM
- Mfr Comm. #:
- LI54.71-P-078498
- Date Added:
- October 22, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint "Active Emergency Stop Assist Currently Unavailable" and "Active Steering Assist Inoperative" instrument cluster messages along with Tire Pressure Light on in Instrument Cluster. Cause Both systems are temporarily unavailable due to low tire pressures. An active tire pressure monitor light may result in some assistance features being temporarily unavailable until tire pressures are corrected. Remedy Check/adjust tire pressures and reset monitoring through the instrument cluster.
Associated Products (58)2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz GLE-Class2022 Mercedes-Benz S-Class2022 Mercedes-Benz SL-Class2021 Mercedes-Benz AMG GT+ 38 moreAssociated Documents - October 3, 2024•Document ID: 11008880Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- LI82.85-P-078473
- Date Added:
- October 9, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": • The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). • In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": • The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). • In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
Associated Products (134)2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLE-Class+ 114 moreAssociated Documents - September 28, 2024•Document ID: 11008091Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- LI82.70-P-077433
- Date Added:
- September 28, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: • It is recommended to replace the cover caps. • The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way.
Associated Products (263)2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLE2023 Mercedes-Benz CLS-Class+ 243 moreAssociated Documents - September 25, 2024•Document ID: 11008072Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- LI82.70-P-078425
- Date Added:
- September 27, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint White plastic insert present on microphone assembly. See figure A for example. Cause The insert (breathable filter) is designed to be inside for dust protection and air flow control. Remedy Do not remove the breathable filter from the microphone assembly. This part is designed to be in the microphone and should remain in the vehicle. Note: If TIPS support is required for microphone symptoms please open a TIPS case and reference this LI.
Associated Products (31)2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz G-Class2022 Mercedes-Benz GLE-Class2021 Mercedes-Benz E-Class2021 Mercedes-Benz G-Class2021 Mercedes-Benz GLE-Class2020 Mercedes-Benz E-Class2020 Mercedes-Benz G-Class2020 Mercedes-Benz GLE-Class2019 Mercedes-Benz E-Class2019 Mercedes-Benz G-Class+ 11 moreAssociated Documents - September 21, 2024•Document ID: 11007965Service Bulletin/Repair InstructionsSTRUCTURE:BODY
- Mfr Comm. #:
- LI98.00-P-078306
- Date Added:
- September 24, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint When unpacking vehicles with magno night black paint (code 056U) from the full transportation packaging, the paintwork may exhibit white stains/shades on the hood. These are mainly present on the hood, fenders and the bumpers. Cause Moisture ingress under the full transportation packaging can lead to it penetrating the fresh paint thereby causing it to swell up. Easily visible, white stains/shades on the paint surface would be the consequence. Remedy Carefully heat any prominent areas using a heat gun (up-to 900°F, at distance of approx. 3-5 inches), it may be necessary to repeat this process several times. Use a maximum of 120 °C for component parts made of plastic, such as bumpers. If this method does not provide a remedy, the paint structure is irreversibly damaged and not repairable. In such instances, the component part must be repainted. IMPORTANT! Make sure that no seals or other heat-sensitive component parts in the working area or behind the component part are damaged.
Associated Products (6)Associated Documents - September 21, 2024•Document ID: 11007974Service Bulletin/Repair InstructionsEXTERIOR LIGHTING
- Mfr Comm. #:
- LI82.10-P-078307
- Date Added:
- September 24, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. • If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: • LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system • LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
Associated Products (263)2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLE2023 Mercedes-Benz CLS-Class+ 243 moreAssociated Documents - September 18, 2024•Document ID: 11008006Service Bulletin/Repair InstructionsFORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL; FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING; ELECTRICAL SYSTEM
- Mfr Comm. #:
- LI54.71-P-078112
- Date Added:
- September 25, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint "Active Distance Assist currently unavailable" and "Active Brake Assist functions currently limited" are shown on the instrument cluster during startup or while driving AND stored DTC in quick test U0416FE - "Implausible data were received from control unit Traction system" in A108/1 (Distronic). Cluster messages will remain and mentioned system functionality is limited until key is cycled. Cause Under investigation. Symptom may occur with one or a combination of the following: 1. Low battery health 2. Battery state of charge 3. Repeated short drive cycles. Cluster messages will resolve after a vehicle key cycle. Remedy Please open a TIPS case with: • Quick test • A108/1 (Distronic) control unit log • Instrument cluster message memory • Driving Battery Cycle "Individual values while driving" Log (Front SAM) • Battery health • Battery state of charge
Associated Products (14)2024 Mercedes-Benz G-Class2023 Mercedes-Benz G-Class2022 Mercedes-Benz G-Class2021 Mercedes-Benz G-Class2020 Mercedes-Benz G-Class2019 Mercedes-Benz G-Class2018 Mercedes-Benz G-Class2017 Mercedes-Benz G-Class2016 Mercedes-Benz G-Class2015 Mercedes-Benz G-Class2014 Mercedes-Benz G-Class2013 Mercedes-Benz G-Class2011 Mercedes-Benz G-Class2010 Mercedes-Benz G-ClassAssociated Documents - September 17, 2024•Document ID: 11008032Service Bulletin/Repair InstructionsSERVICE BRAKES
- Mfr Comm. #:
- LI42.10-P-063502
- Date Added:
- September 25, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Noises/ squealing from the service brake in various driving situations and ambient conditions Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions. These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. (Extract from the owner's manual) If customer complaints are received, please proceed as follows: • Check whether, apart from this document, an additional document exists for the model series in question, and if so, work through it • Check whether the complaint can be reproduced and at which axle the noises occur (ideally together with the customer while driving) • Check the friction pairings of the affected axle for wear, mechanical damage or localized overheating damage. a) If this is the case, replace the damaged component parts and assess the brake again with regard to noise. b) If there no obvious visible or technical problems with the brake system, we recommend bedding in the brakes by following the procedure below: • Before trip, the mileage incurred must be clarified with the customer (approx. 50 km) • Select a suitable route • Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 100 km/h to 50 km/h (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1.5 km between brake applications • Finally drive approx. 5 km to allow the system to cool • Reassess the problem If this action fails to deliver the desired success, create a TIPS case with the following information: • Observe SI00.00-P-0086A • Have parts already been replaced? If yes, when and which parts (date, mileage)? • How is the customer's driving profile, and when/where is it reproducible? • Create a video/ sound file • Attach usable pictures of the brake components on the affected axle (important: including the back of the lining)
Associated Products (128)2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz G-Class2022 Mercedes-Benz GLC-Class+ 108 moreAssociated Documents - September 15, 2024•Document ID: 11008055Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- LI06.20-P-078392
- Date Added:
- September 26, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Customer states check engine light is on. Cause Software needs to be updated. Remedy Please update the ME control unit software. The new software should include 1779021216 and or 1769036201. If neither of these numbers is present and an update is not available, check vedoc to see if the vehicle had one of these software numbers at one point. Assess the vehicle after the flash and if the complaint is remedied, release the vehicle. If the customer complaint is not remedied, process the vehicle via LI07.61-P-070707 and open a TIPS case with your findings. If the vehicle is already at this software level or if software is not available and it never had it previously, process the vehicle via LI07.61-P-070707 and open a TIPS case with your findings.
Associated Products (4)Associated Documents - September 12, 2024•Document ID: 11007785Service Bulletin/Repair InstructionsENGINE; ELECTRICAL SYSTEM
- Mfr Comm. #:
- LI07.70-P-074820
- Date Added:
- September 14, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Engine does not restart after ECO stop. All indicator lights come on in instrument cluster. Engine can be restarted normally with ignition switch. Fault codes P1CE200, P1D0500, or P1CDF00 may be stored in powertrain control unit N127. Cause ME control unit software Remedy Update software of ME control unit N3/10. New software part numbers A1779021216 A1779036201
Associated Products (4)Associated Documents - September 10, 2024•Document ID: 11007753Service Bulletin/Repair InstructionsEXTERIOR LIGHTING
- Mfr Comm. #:
- LI82.10-P-078301
- Date Added:
- September 13, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
Associated Products (263)2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLE2023 Mercedes-Benz CLS-Class+ 243 moreAssociated Documents