Toyota Tundra Complaints

6,958 consumer complaints on file.

• #11595427June 20, 2024
  SEATS

  Driver's Seat appears to have some play in it where when accelerating or coming to a stop, the seat bottom will move forward and/or backwards. This has continued to happen and after repeated attempts to have the dealer resolve it, they have basically told me it was designed that way. We've never had another Toyota product do this. We do understand there are certain specifications needed to meet safety requirements, but we've sat and driven in other models of the same specifications and their seats do not do this.

  Crash:

  No

  Fire:

  No

  Injuries:

  0

  Deaths:

  0

• #11595424June 20, 2024
  SEATS

  Since around 35,000 miles, the 10-way Power Adjustable Driver's Seat makes a terrible squeaky sound when going over any bumps in the road. If the Driver were to move while in the seat, the squeak is present. We have already paid out of pocket (not considered a warranty issue because nothing is "broken"), but the squeak has returned. This is no fault of the dealership, but because of the design that Toyota implemented for just the 10-way Power Adjustable Driver's Seat. If we reduce the Lumbar Support down to its lowest setting, the squeak gets better but it makes the seat that much more uncomfortable. These are the worst seats we've ever had in any vehicle, let alone a Toyota/Lexus product.

  Crash:

  No

  Fire:

  No

  Injuries:

  0

  Deaths:

  0

• #11595422June 20, 2024
  SEATS

  Since around 35,000 miles, the 10-way Power Adjustable Driver's Seat makes a terrible squeaky sound when going over any bumps in the road. If the Driver were to move while in the seat, the squeak is present. We have already paid out of pocket (not considered a warranty issue because nothing is "broken"), but the squeak has returned. This is no fault of the dealership, but because of the design that Toyota implemented for just the 10-way Power Adjustable Driver's Seat. If we reduce the Lumbar Support down to its lowest setting, the squeak gets better but it makes the seat that much more uncomfortable. These are the worst seats we've ever had in any vehicle, let alone a Toyota/Lexus product.

  Crash:

  No

  Fire:

  No

  Injuries:

  0

  Deaths:

  0

• #11595420June 20, 2024
  SEATS

  Since around 35,000 miles, the 10-way Power Adjustable Driver's Seat makes a terrible squeaky sound when going over any bumps in the road. If the Driver were to move while in the seat, the squeak is present. We have already paid out of pocket (not considered a warranty issue because nothing is "broken"), but the squeak has returned. This is no fault of the dealership, but because of the design that Toyota implemented for just the 10-way Power Adjustable Driver's Seat. If we reduce the Lumbar Support down to its lowest setting, the squeak gets better but it makes the seat that much more uncomfortable. These are the worst seats we've ever had in any vehicle, let alone a Toyota/Lexus product.

  Crash:

  No

  Fire:

  No

  Injuries:

  0

  Deaths:

  0

• #11595364June 19, 2024
  ENGINE, FUEL/PROPULSION SYSTEM, POWER TRAIN

  At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).

  Crash:

  No

  Fire:

  No

  Injuries:

  0

  Deaths:

  0

• #11595363June 19, 2024
  FUEL/PROPULSION SYSTEM, ENGINE, POWER TRAIN

  At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).

  Crash:

  No

  Fire:

  No

  Injuries:

  0

  Deaths:

  0

• #11595362June 19, 2024
  ENGINE, FUEL/PROPULSION SYSTEM, POWER TRAIN

  At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).

  Crash:

  No

  Fire:

  No

  Injuries:

  0

  Deaths:

  0

• #11595357June 19, 2024
  ENGINE, FUEL/PROPULSION SYSTEM, POWER TRAIN

  At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).

  Crash:

  No

  Fire:

  No

  Injuries:

  0

  Deaths:

  0

• #11595355June 19, 2024
  ENGINE, FUEL/PROPULSION SYSTEM, POWER TRAIN

  At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).

  Crash:

  No

  Fire:

  No

  Injuries:

  0

  Deaths:

  0

• #11595350June 19, 2024
  ENGINE, FUEL/PROPULSION SYSTEM, POWER TRAIN

  At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modified to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into traffic in slower moving city streets. There are members of an online forum who have been able to record the data flow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10-AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/Sequoia).

  Crash:

  No

  Fire:

  No

  Injuries:

  0

  Deaths:

  0

• #11595349June 19, 2024
  ENGINE, POWER TRAIN, FUEL/PROPULSION SYSTEM

  At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modified to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into traffic in slower moving city streets. There are members of an online forum who have been able to record the data flow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10-AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/Sequoia).

  Crash:

  No

  Fire:

  No

  Injuries:

  0

  Deaths:

  0

• #11595180June 18, 2024
  ENGINE

  My truck engine was stalled shortly couple times on me. 1- When I try to turn right to get out of my sub division in the morning, my truck stalled. I released the gas paddle and step on it again and this time the truck is going ok. Luckily the coming car be able to stop before hitting my truck. 2- One time I went out for lunch with a friend, when we got back to the company's parking lot, I tried to back up the truck and the truck one stalled. I released the gas paddle and step on it again and it is ok. My friend thought it may be the rain outside.

  Crash:

  No

  Fire:

  No

  Injuries:

  0

  Deaths:

  0

• #11594840June 17, 2024
  STRUCTURE:BODY

  Frame of truck rusting apart Rust problem identified by independent dealer. I was told by repair shop that the frame could twist apart at any moment.

  Crash:

  No

  Fire:

  No

  Injuries:

  0

  Deaths:

  0

• #11594302June 13, 2024
  TIRES

  Tire size275/55/R20 Back Country AT2 had complete sidewall detachment while going 75 on free-way. Tires appeared to be in good condition prior to incident. There were no potholes or road conditions that contributed to incident. This nearly resulted in a freeway speed rollover.

  Crash:

  No

  Fire:

  No

  Injuries:

  0

  Deaths:

  0

• #11594275June 13, 2024
  AIR BAGS

  The contact owned a 2023 Toyota Tundra. The contact stated while driving at an undisclosed speed he began to lose control of the vehicle in which he stated the vehicle would swerve uncontrollably. The contact also stated that his trailer had detached from the tailgate which caused the trailer to jackknife the rear end of the vehicle which cause his rear tire to blow out which caused the vehicle to stop and not crash into any objects No medical attention was needed but the contact drove himself to the hospital after the accident and stated he still suffers from emotional damage. A police report was filed. The vehicle and trailer were towed to a storage facility. The contact also stated that the air bags did not implode during the accident. The dealer was contacted, and the vehicle was not repaired The manufacturer was made aware of the failure. The failure mileage was approximately 18,000.

  Crash:

  Yes

  Fire:

  No

  Injuries:

  0

  Deaths:

  0

• #11594182June 13, 2024
  ENGINE, UNKNOWN OR OTHER

  Toyota has recall, stall engine , knocking noise

  Crash:

  No

  Fire:

  No

  Injuries:

  0

  Deaths:

  0

• #11593883June 12, 2024
  SUSPENSION, STEERING, UNKNOWN OR OTHER

  The vehicle did not pass PA state inspection due to broken front shock mounts and severe frame corrosion.

  Crash:

  No

  Fire:

  No

  Injuries:

  0

  Deaths:

  0

• #11593990June 12, 2024
  STRUCTURE:FRAME AND MEMBERS

  The contact owns a 2005 Toyota Tundra. The contact stated that the sub frame was rusted and had holes. The parking brake and oil warning lights were illuminated. The vehicle was taken to the local dealer, who determined that the vehicle might not pass a safety inspection due to the position of the holes and rust. The warning lights were repaired but the sub frame was not repaired. The vehicle was taken to a frame shop, the frame shop declined to service the vehicle. The manufacturer was contacted and informed the contact about an Extended Warranty, but no assistance was provided. The failure mileage was approximately 139,000.

  Crash:

  No

  Fire:

  No

  Injuries:

  0

  Deaths:

  0

• #11594037June 12, 2024
  UNKNOWN OR OTHER

  Big Hesitation on the throttle response when accelerating, so much so as almost causing accident due to delay from hitting gas pedal to acceleration

  Crash:

  No

  Fire:

  No

  Injuries:

  0

  Deaths:

  0

• #11593982June 12, 2024
  SERVICE BRAKES

  Rotors have been replaced once already. Still vibrating severely during braking at 50-60 mph speeds. Especially downhill.

  Crash:

  No

  Fire:

  No

  Injuries:

  0

  Deaths:

  0