Ford F-550 Service Bulletins
1,630 manufacturer communications on file.
- October 3, 2023•Document ID: 10244822Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- SSM 51959
- Date Added:
- November 3, 2023
- Manufacturer:
- FORD
SummaryWhen replacing the transmission case on a 2020-2022 F-Super Duty equipped with a 10R140 transmission, the new service case may not come equipped with the transmission fluid leveling plug. To achieve proper transmission fluid level, a new transmission fluid pan and gasket must be installed (service part PC3Z-7A194-A). Refer to the 2023 F-Super Duty Workshop Manual, Section 307-01B to properly set the transmission fluid level when using the newer transmission fluid pan.
Associated Products (12)Associated Documents - September 30, 2023•Document ID: 10243420Service Bulletin/Repair InstructionsSTEERING
- Mfr Comm. #:
- 23B55
- Date Added:
- October 3, 2023
- Manufacturer:
- FORD
SummaryCertain 2023 Model Year Super Duty Vehicles - Perform Vehicle Alignment
Associated Products (7)Associated Documents - September 30, 2023•Document ID: 10243419Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 23B52
- Date Added:
- October 3, 2023
- Manufacturer:
- FORD
SummaryCertain 2023 Model Year F-250 â F-600 Single Rear Wheel (SRW) Series Vehicles - Incorrect Lug Wrench
Associated Products (5)Associated Documents - September 27, 2023•Document ID: 10243652Service Bulletin/Repair InstructionsEQUIPMENT; ELECTRICAL SYSTEM
- Mfr Comm. #:
- SSM 51947
- Date Added:
- October 6, 2023
- Manufacturer:
- FORD
SummarySome 2015-2019 F-Super Duty and 2015-2020 F-150/Mustang vehicles may require replacement of the powertrain control module (PCM) for various reasons. While performing a programmable module installation (PMI) using the Integrated Diagnostic Service (IDS) scan tool, an error message may state: Configuration Failed, Would You Like To Retry? This may be due to improper module replacement steps. Make sure that the original module is installed in the vehicle, delete the vehicle session, then start a new vehicle session. Once the session starts, run the PCM PMI and install the new PCM only when the scan tool instructs. Finish the PMI by following the prompts given by IDS. If the original PCM is not available, it is possible to configure the module by running as-built programming on the PCM. When IDS asks to obtain part numbers or configuration data, select configuration data.
Associated Products (32)2020 Ford F-1502020 Ford Mustang2019 Ford F-1502019 Ford F-2502019 Ford F-3502019 Ford F-4502019 Ford F-5502019 Ford Mustang2018 Ford F-1502018 Ford F-2502018 Ford F-3502018 Ford F-4502018 Ford F-5502018 Ford Mustang2017 Ford F-1502017 Ford F-2502017 Ford F-3502017 Ford F-4502017 Ford F-5502017 Ford Mustang+ 12 moreAssociated Documents - September 25, 2023•Document ID: 10242859Service Bulletin/Repair InstructionsBACK OVER PREVENTION:SOFTWARE; POWER TRAIN; ELECTRICAL SYSTEM
- Mfr Comm. #:
- TSB 23-2297
- Date Added:
- September 26, 2023
- Manufacturer:
- FORD
SummarySome 2023 F-Super Duty vehicles built on or before 29-Aug-2023 and equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P060C, U1022, P0093, P01C4, U3012, P24C7, P06E9, P0364, P1942, P162E, P061A, P2201, and/or P2698 stored in the powertrain control module (PCM). This may be due to the software in the PCM.
Associated Products (4)Associated Documents - September 21, 2023•Document ID: 10243440Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:INFOTAINMENT; EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE
- Mfr Comm. #:
- SU5 P3 SuperDuty
- Date Added:
- October 3, 2023
- Manufacturer:
- FORD
Summary"Software Update SU5 P3 for 2023 Super Duty Vehicles is now available. Quality improvements include: '- Adds a ""some display features may be temporarily unavailable"" message to the SYNC screen when a SYNC update is installing. - Add previously missing keyboard display in ""add trailer"" menu screen - Turns on missing Lane keep Assist sensitivity menu"
Associated Products (4)Associated Documents - September 21, 2023•Document ID: 10243648Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- SSM 51939
- Date Added:
- October 6, 2023
- Manufacturer:
- FORD
SummarySome 2017-2023 Ford and Lincoln vehicles equipped with a 10R60/10R80/10R80 MHT/10R100 transmission may exhibit a whine noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P) position. A small amount of whine noise is considered to be characteristic of the 10R60/10R80/10R80 MHT/10R100 transmissions due to the offset gear drivetrain in the front support and has no effect on durability. Use the Report a Vehicle Concern link at the bottom of OASIS to submit a report if there is a customer concern of whine noise describing operating conditions and noise severity.
Associated Products (49)2023 Ford Bronco2023 Ford Expedition2023 Ford Explorer2023 Ford F-1502023 Ford F-2502023 Ford F-3502023 Ford F-4502023 Ford F-5502023 Ford Mustang2023 Ford Ranger2023 Ford Transit2023 Lincoln Aviator2023 Lincoln Navigator2022 Ford Bronco2022 Ford Expedition2022 Ford Explorer2022 Ford F-1502022 Ford Mustang2022 Ford Ranger2022 Ford Transit+ 29 moreAssociated Documents - September 20, 2023•Document ID: 10243609Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- SSM 51937
- Date Added:
- October 5, 2023
- Manufacturer:
- LINCOLN
SummarySome vehicles equipped with power folding mirrors may exhibit power folding mirrors that are inoperative or exhibit a clicking sound. This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.
Associated Products (59)2023 Ford Expedition2023 Ford Explorer2023 Ford F-1502023 Ford F-2502023 Ford F-3502023 Ford F-4502023 Ford F-5502023 Lincoln Aviator2023 Lincoln Navigator2022 Ford Expedition2022 Ford Explorer2022 Ford F-1502022 Ford F-2502022 Ford F-3502022 Ford F-4502022 Ford F-5502022 Lincoln Aviator2022 Lincoln Navigator2021 Ford Expedition2021 Ford Explorer+ 39 moreAssociated Documents - September 19, 2023•Document ID: 10243431Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:INFOTAINMENT; EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE
- Mfr Comm. #:
- SU4P3 SD 22MY
- Date Added:
- October 3, 2023
- Manufacturer:
- FORD
Summary"Software Update SU4 P3 for 2022 Super Duty Vehicles is now available. Quality improvements include: -Various Apple Carplay quality improvements"
Associated Products (4)Associated Documents - September 18, 2023•Document ID: 10243542Service Bulletin/Repair InstructionsBACK OVER PREVENTION:SOFTWARE
- Mfr Comm. #:
- SSM 51929
- Date Added:
- October 4, 2023
- Manufacturer:
- FORD
SummarySome 2023 F-Super Duty vehicles may exhibit diagnostic trouble code (DTC) C006A:00 in the telematics control unit module (TCU). If this is a stand alone DTC and no other codes are present, this may be due to a TCU software concern. To correct the condition, reprogram the TCU using the latest software level of the Ford Diagnosis and Repair System (FDRS) located under the SW Updates tab. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Associated Products (4)Associated Documents - September 7, 2023•Document ID: 10243490Service Bulletin/Repair InstructionsPOWER TRAIN:AUTOMATIC TRANSMISSION
- Mfr Comm. #:
- SSM 51909
- Date Added:
- October 4, 2023
- Manufacturer:
- FORD
SummaryWhen performing any transmission fluid changes or topoffs involving MERCON SP, MERCON LV has replaced all versions of MERCON SP and can be used going forward. Mixing MERCON LV and MERCON SP in the same transmission is acceptable. After 30-Jun-2023, MERCON SP ATF will no longer be manufactured and will only be available until inventory depletes.
Associated Products (56)2008 Ford E-1502008 Ford E-2502008 Ford E-3502008 Ford E-4502008 Ford Expedition2008 Ford Explorer2008 Ford F-2502008 Ford F-3502008 Ford F-4502008 Ford F-5502008 Lincoln Navigator2008 Mercury Mountaineer2007 Ford E-1502007 Ford E-2502007 Ford E-3502007 Ford E-4502007 Ford Expedition2007 Ford Explorer2007 Ford F-2502007 Ford F-350+ 36 moreAssociated Documents - September 4, 2023•Document ID: 10243479Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SSM 51903
- Date Added:
- October 4, 2023
- Manufacturer:
- FORD
SummarySome 2021-2023 Ford and Lincoln vehicles may exhibit DTCs U2100 and/or U3002 stored in the cruise control module (CCM), side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement. DTC U2100 may set when the module has not been properly configured after replacement. DTC U3002 may set when the module has been configured with the incorrect VIN. To correct this condition, verify that the module storing the DTC has been installed following the applicable Workshop Manual (WSM) Removal and Installation procedure. If the DTC is still stored, download and run the Vehicle Identification Number (VIN) Write application found under Toolbox, Multi-Module tab in the Ford Diagnosis and Repair System (FDRS).
Associated Products (16)Associated Documents - August 31, 2023•Document ID: 10241951Service Bulletin/Repair InstructionsFUEL SYSTEM, DIESEL
- Mfr Comm. #:
- 22N05 S1
- Date Added:
- September 6, 2023
- Manufacturer:
- FORD
SummaryCertain 2022 Model Year Super Duty 6.7L Diesel Engine - One-Time Replacement for Diesel Particulate Filter Assembly Failures Supplement 1
Associated Products (7)Associated Documents - August 31, 2023•Document ID: 10241949Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 22L03
- Date Added:
- September 6, 2023
- Manufacturer:
- FORD
SummaryCertain 2021-2022 Model Year Econoline, Super Duty Chassis Cab, F53 Motor Home, F59 Step Van, and F650/F750 Medium Duty Chassis Cab Vehicles Equipped with a Premium Rated 7.3L Engine - Engine Horsepower Credit
Associated Products (22)2022 Ford E-1502022 Ford E-2502022 Ford E-3502022 Ford E-4502022 Ford F-2502022 Ford F-3502022 Ford F-4502022 Ford F-5502022 Ford F-6002022 Ford F-6502022 Ford F-7502021 Ford E-1502021 Ford E-2502021 Ford E-3502021 Ford E-4502021 Ford F-2502021 Ford F-3502021 Ford F-4502021 Ford F-5502021 Ford F-600+ 2 moreAssociated Documents - August 28, 2023•Document ID: 10241617Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM
- Mfr Comm. #:
- SSM 51891
- Date Added:
- September 4, 2023
- Manufacturer:
- FORD
SummarySome 2023 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) U02A2, P206B, P203B, P208A, P20FA, P20FD, and/or P20FC stored in the powertrain control module (PCM). Before performing normal diagnostics, inspect connectors C1273C (32 pin) and C406 (14 pin) for proper connection. Also disconnect and inspect C1415 (32 pin), C406 (14 pin), C4863 (7 pin) and C4864 (5 pin) for signs of water intrusion and/or corrosion. Refer to the Wiring Diagram for connector locations. Repair as necessary. Refer to Wiring Diagram Cell 005 for repair procedures.
Associated Products (4)Associated Documents - August 18, 2023•Document ID: 10241992Service Bulletin/Repair InstructionsBACK OVER PREVENTION:SOFTWARE
- Mfr Comm. #:
- SU4 P2 SuperDuty
- Date Added:
- September 7, 2023
- Manufacturer:
- FORD
SummarySoftware Update 4 P2 for 2023 Super Duty vehicles is now available. Quality improvements include: -12V key off load improvement. - wifi hotspot reconfigured to support 5G.
Associated Products (7)Associated Documents - August 11, 2023•Document ID: 10241991Service Bulletin/Repair InstructionsBACK OVER PREVENTION:SOFTWARE
- Mfr Comm. #:
- SU5 P2 SuperDuty
- Date Added:
- September 7, 2023
- Manufacturer:
- FORD
SummarySoftware Update 5 P2 for 2023 Super Duty vehicles is now available. Quality improvements include: - Enables the Lane Keep Assist sensitivity menu - Improvement to Pro Power Onboard (PPO) pop-up message to allow it to clear - Changed pop-up message that displays when exiting the camera view - Add in-vehicle message on infotainment screen to inform customer that some display features may be unavailable while SYNC is rebooting during SYNC OTA update installation.
Associated Products (7)Associated Documents - August 11, 2023•Document ID: 10241990Service Bulletin/Repair InstructionsBACK OVER PREVENTION:SOFTWARE
- Mfr Comm. #:
- SU4 P1 SuperDuty
- Date Added:
- September 7, 2023
- Manufacturer:
- FORD
SummarySoftware Update 4 P1 for 2022 Super Duty vehicles is now available. Quality improvements include: - Minimize time customer cannot enter the vehicle during future inhibit updates.
Associated Products (7)Associated Documents - August 10, 2023•Document ID: 10241626Service Bulletin/Repair InstructionsPOWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN:MANUAL TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
- Mfr Comm. #:
- SSM 51854
- Date Added:
- September 4, 2023
- Manufacturer:
- FORD
SummaryVarious 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS > Diagnostics tab > HVBoM > Features > Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
Associated Products (54)2019 Ford E-3502019 Ford E-4502019 Ford F-2502019 Ford F-3502019 Ford F-4502019 Ford F-5502019 Ford F-6502019 Ford F-7502018 Ford E-3502018 Ford E-4502018 Ford F-2502018 Ford F-3502018 Ford F-4502018 Ford F-5502018 Ford F-6502018 Ford F-7502017 Ford E-2502017 Ford E-3502017 Ford E-4502017 Ford F-250+ 34 moreAssociated Documents - August 8, 2023•Document ID: 10241547Service Bulletin/Repair InstructionsPOWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
- Mfr Comm. #:
- SSM 51849
- Date Added:
- September 1, 2023
- Manufacturer:
- FORD
SummaryVarious 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
Associated Products (56)2019 Ford E-3502019 Ford E-4502019 Ford F-2502019 Ford F-3502019 Ford F-4502019 Ford F-5502019 Ford F-6502019 Ford F-7502018 Ford E-3502018 Ford E-4502018 Ford F-2502018 Ford F-3502018 Ford F-4502018 Ford F-5502018 Ford F-6502018 Ford F-7502017 Ford E-2502017 Ford E-3502017 Ford E-4502017 Ford F-250+ 36 moreAssociated Documents