BMW 528i Service Bulletins
504 manufacturer communications on file.
- June 1, 2016•Document ID: 10151375Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- B621016
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryHeadUp Display does not Show Full Street Names. INFORMATION Design of the HUD has limited display area. (It can only show a certain number of text characters). NOTE: Parts replacement or programming the vehicle will not recitify the situation!
Associated Products (168)Associated Documents - June 1, 2016•Document ID: 10151355Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE; ENGINE
- Mfr Comm. #:
- B120516
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary"N55 - ENGINE MALFUNCTION WARNING DUE TO VAPOR FORMING IN THE FUEL SYSTEM This Service Information bulletin supersedes SI B12 05 16 dated April 2016. The Engine ""Drivetrain Malfunction"" Check Control warning is displayed and the Service Engine Soon (MIL) Lamp may also be on. In areas where winterized fuel is used, this situation may occur after prolonged periods of engine idling or ""stop and go"" driving. Additional symptoms that may be present: rough running poor engine performance difficulty in starting the engine. Either or both of the following fault codes can be stored in the DME. 11A002 - Fuel high pressure, plausibility: Pressure too low 11AC02 - Fuel high pressure, plausibility, cold start: Pressure too low In addition any of the following faults may also be stored: 119404 - Rail pressure sensor, signal: Permanently stuck 118001 - Mixture control: mixture too lean 118401 - Mixture control: mixture too lean; large deviation Vapor formation in the fuel system from fuel quality characteristics of certain winter fuel blends along with high engine compartment temperatures."
Associated Products (48)Associated Documents - June 1, 2016•Document ID: 10151353Service Bulletin/Repair InstructionsENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE
- Mfr Comm. #:
- B110716
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryDiesel Engine: Intake Manifold Damaged. The Service Engine Soon light is on. There may also be: Complaints of lack of engine performance An exhaust smell coming from the engine area. The following fault codes may be stored in the DDE: 24CE00 - Hot film air mass meter: Ratio of measured to calculated air mass too high 27F000 - Charge air hose monitoring in idle: Charge air hose fallen down 290900 - Air system, air to EGR air mass flow plausibility: Measured air mass compared to calculated air mass too high 290A00 - Air system, air to EGR air mass flow plausibility: measured air mass compared to calculated air mass too high and high charging pressure control deviation 1. Excessive thermal load from the EGR system on the intake components 2. An excessive or unmetered air leak in the intake/charge air system
Associated Products (61)Associated Documents - May 1, 2016•Document ID: 10151335Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- B840314
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryBluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware.
Associated Products (264)Associated Documents - May 1, 2016•Document ID: 10151333Service Bulletin/Repair InstructionsVEHICLE SPEED CONTROL:CRUISE CONTROL; EQUIPMENT; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL
- Mfr Comm. #:
- B660916
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary"""Collision Warning Failed"" or ""Pedestrian Warning Failed"" CCM Display. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield; And/ or: The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. This picture shows the KAFAS camera installed in the bracket. Notice the spacing highlighted by the ""green lines"""
Associated Products (126)Associated Documents - May 1, 2016•Document ID: 10151331Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- B651216
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryIntegrated Navigation Voice Not Loud Enough. Integrated Navigation voice guidance is not loud enough to be heard over loud music. Software error in the CHAMP2 Head Unit.
Associated Products (34)Associated Documents - May 1, 2016•Document ID: 10151325Service Bulletin/Repair InstructionsENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM
- Mfr Comm. #:
- B620816
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryIncomplete AdBlue Check Control Message (CCM) on the Central Information Display. An incorrectly displayed AdBlue (Diesel Exhaust Fluid refill range) CCM is shown on the Central Information Display. Improper instrument cluster software
Associated Products (29)Associated Documents - May 1, 2016•Document ID: 10151324Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- B620716
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryUnintentional Active ECO-PRO Bonus Miles Reset. Fluctations of fuel level (causing resistance changes in the level sensor) while vehicle is stationary, are interpreted as refueling. This causes active ECO PRO mode bonus range to reset. Error in instrument cluster application.
Associated Products (82)Associated Documents - May 1, 2016•Document ID: 10151323Service Bulletin/Repair InstructionsSTEERING
- Mfr Comm. #:
- B612906
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryELV Does Not Release. The customer complains of a no-crank, no-start situation. The condition may be intermittent. The ELV (Electric Steering Lock) warning is shown in the Instrument Cluster.
Associated Products (39)Associated Documents - May 1, 2016•Document ID: 10151312Service Bulletin/Repair InstructionsSTEERING
- Mfr Comm. #:
- B320616
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryTroubleshooting intermittent Steering Assistance with Electric Power Steering (EPS). Intermittent steering assistance failure CAUSE The power supply of the EPS control unit.
Associated Products (88)Associated Documents - May 1, 2016•Document ID: 10151303Service Bulletin/Repair InstructionsEQUIPMENT; ENGINE
- Mfr Comm. #:
- B111715
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary"N63, N63TU and N63R Engines: Upper Oil Pan Removal and Installation Repair Instructions This Service Information bulletin supersedes SI B11 17 15 dated August 2015.. INFORMATION When removing and/or installing the engine upper oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the engine upper oil pan refer to the newly released Repair Instruction 11 13 010 ""Removing and installing/replacing upper oil sump"" in ISTA/D 3.55.11 or higher for the proper procedures. IMPORTANT: The new repair instructions will state one of the following before reinstalling the upper engine oil pan. ""All threads must be cleaned with screw tap"" Or ""Clean all threads with screw tap. Order number 81 43 0 402 559"" Or ""Clean all threads with a thread cutter"". The current repair instruction terminology will be modified to include this information."
Associated Products (104)Associated Documents - May 1, 2016•Document ID: 10151302Service Bulletin/Repair InstructionsPOWER TRAIN; POWER TRAIN:CLUTCH ASSEMBLY:BELL HOUSING
- Mfr Comm. #:
- B110916
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryN63, N63TU, S63 and S63TU Engines: Oil Leak from the Rear of the Engine and Transmission Bell Housing. Customer complains that engine oil is leaking from the center of the vehicle. When verified, the engine oil residue can be seen leaking from between the engine and the transmission bell housing.
Associated Products (96)Associated Documents - May 1, 2016•Document ID: 10151301Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B110815
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryN63 and S63 Engine: Valve Seal Replacement This Service Information bulletin and attachment supersedes SI B11 08 15 dated March 2016. Refer to the following applicable SIBs before replacing the valve seals. SI B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs SI B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints SI B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity SI B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil
Associated Products (58)Associated Documents - May 1, 2016•Document ID: 10151300Service Bulletin/Repair InstructionsENGINE; EQUIPMENT
- Mfr Comm. #:
- B110616
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryN51, N52, N52K and N52T Engines: Various Eccentric Shaft Sensor Faults stored in the DME - Diagnostic Hints This Service Information bulletin and attachment supersedes SI B11 06 16 dated April 2016.. The customer may complain about one of the following: Rough engine running Engine cannot be started (crank no start) Check Engine Light illuminated One or more of the following faults may be stored in the DME: 2A37 - Valvetronic, eccentric shaft sensor plausibility 2A47 - Valvetronic, eccentric shaft, signal plausibility 134E08 - Eccentric shaft plausibility (on F10, F25 vehicles only) CAUSE The VVT eccentric shaft sensor connector, and/or DME connector may have oil contamination due to oil leakage at the VVT sensor gasket.
Associated Products (50)Associated Documents - April 14, 2016•Document ID: 10216791Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- TEC24
- Date Added:
- August 1, 2022
- Manufacturer:
- BMW
SummaryTech24 Snap-in Adapter Return
Associated Products (59)Associated Documents - April 1, 2016•Document ID: 10216793Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- TEC26
- Date Added:
- August 1, 2022
- Manufacturer:
- BMW
SummaryTEC26 Turbo Charger Return
Associated Products (59)Associated Documents - April 1, 2016•Document ID: 10151274Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B840715
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummarySOS Malfunction Is Displayed In Kombi Sporadically. After engine start-up, a CCM (Check Control Message) for SOS malfunction is displayed in the Kombi and in the CID (Central Information Display). One or more of the fault codes below may be stored in the TCB or Combox control unit: 0xB7F32B - GSM Antenna: Open Circuit 0xB7F31F - GSM Antenna: Short to ground 0xB7F31E - GSM Antenna: Open Circuit A signal error is identified during the aerial self-test performed by the TCB (Telematic Control Box or the Combox).
Associated Products (127)Associated Documents - April 1, 2016•Document ID: 10151253Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR
- Mfr Comm. #:
- B120916
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryN20 - The Service Engine Soon Light is On with DME Fault 118602 Stored. The Service Engine Soon light is on (MIL) with only the following oxygen sensor fault stored. 118602 - Oxygen sensor before catalytic converter, fine mixture control: exhaust gas after catalytic converter too lean CAUSE An actual engine related problem and/or DME software diagnostic
Associated Products (61)Associated Documents - April 1, 2016•Document ID: 10151250Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B120516
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary"N55 - Engine Malfunction Warning Due to Vapor Forming in the Fuel System. The Engine Drivetrain Malfunction"" Check Control warning is displayed and the Service Engine Soon (MIL) Lamp may also be on. In areas where winterized fuel is used, this situation may occur after prolonged periods of engine idling or ""stop and go"" driving. Additional symptoms that may be present: rough running poor engine performance difficulty in starting the engine. Either or both of the following fault codes can be stored in the DME. 11A002 - Fuel high pressure, plausibility: Pressure too low 11AC02 - Fuel high pressure, plausibility, cold start: Pressure too low In addition any of the following faults may also be stored: 119404 - Rail pressure sensor, signal: Permanently stuck 118001 - Mixture control: mixture too lean 118401 - Mixture control: mixture too lean; large deviation Vapor formation in the fuel system from fuel quality characteristics of certain winter fuel blends along with high engine compartment temperatures."
Associated Products (48)Associated Documents - April 1, 2016•Document ID: 10151249Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:EXHAUST SYSTEM
- Mfr Comm. #:
- B111615
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryN20 and N26 engine: Smoke from Exhaust when Starting a Cold Engine. When starting a cold engine, blue smoke can be seen emitting from the exhaust tailpipe for approximately 10-20 seconds. No turbo charger boost faults are stored and no drivability issues can be detected. CAUSE When the vehicle is parked overnight the engine oil pressure will equalize and may leak past the turbo charger exhaust side turbine seal.
Associated Products (83)Associated Documents