BMW 335i Service Bulletins
690 manufacturer communications on file.
- December 1, 2014•Document ID: 10148190Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:TURN SIGNAL:SWITCH; STRUCTURE:BODY:TRUNK LID; ELECTRICAL SYSTEM:WIRING: REAR COMPARTMENT/TRUNK
- Mfr Comm. #:
- 631113
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryOne or Both Trunk Lid Tail Lamps Malfunction. One of the tail lamps is out in the trunk lid light cluster. This is accompanied by one of the following CCM (Check Control Messages): z Tail lamp in tailgate malfunction z Rear fog light malfunction z Reversing light malfunction z ISTA shows one or more fault(s) present: 80486A - Short-circuit in left-hand reversing light 80486B - Short-circuit in right-hand reversing light 80487F - Rear fog light, left, faulty 804880 - Rear fog light, right, faulty CAUSE The socket housing in the rear lamp mounted on the trunk lid is defective.
Associated Products (9)Associated Documents - December 1, 2014•Document ID: 10148186Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- 613314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryThe Controller Responds Slowly or Not at All. When the customer presses or turns the controller, there is no or a delayed response. This can sporadically occur. Software in the controller
Associated Products (69)Associated Documents - December 1, 2014•Document ID: 10148173Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- 161514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryNVLD Tank Leakage FC 190302 Fuel Tank Ventilation and Purge Air System Micro Leak. The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: z FC 190302 Fuel tank ventilation and purge air system micro leak leakage greater than 0_5 mm CAUSE Contamination of the NVLD pressure switch electrical contacts
Associated Products (106)Associated Documents - December 1, 2014•Document ID: 10148168Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING; POWER TRAIN
- Mfr Comm. #:
- 123314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryFault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
Associated Products (30)Associated Documents - November 1, 2014•Document ID: 10148429Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; LATCHES/LOCKS/LINKAGES:TRUNK LID:LOCK
- Mfr Comm. #:
- 660914
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryUnlocking Trunk with Remote Unlocks All Doors. After programming the vehicle with ISTA/P 2.47.1, unlocking the trunk with the remote changes to unlocking all the doors. An application error occurred after programming the vehicle to the Personal Profile Setting (PIA) in the Front Electronic Module (FEM).
Associated Products (22)Associated Documents - November 1, 2014•Document ID: 10148423Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 610314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCheck Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: z 213901 - Power management: Reduction or shutdown of individual electrical consumer z 8040BD - Reset or deactivation of Terminal 30F z 8040B9 - De-activation of terminal 30B: Top start capability limit reached z 8020E8 - Reset or deactivation of terminal 30F z 800E89 - FRM: start capability limit reached with lights active during stationary mode z 93076B - Deactivation of terminal 30B: upper start capability limit reached z 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active z 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active z 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE z The check control message (ID 229) is caused by a heavily discharged battery. z The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). z In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. z Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. z The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
Associated Products (138)Associated Documents - November 1, 2014•Document ID: 10148420Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS
- Mfr Comm. #:
- 513114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHeadlight Cleaning System: Functional Operation Change. The customer complains that the headlight cleaning system is not working properly and only works after several actuating attempts. CAUSE The "functional" operation of the headlight cleaning system was changed with integration level F020-14-07-500. The functional changes to the headlight cleaning system's operation will occur only after programming the vehicle with ISTA/P 2.53.0 or higher. INFORMATION The headlight cleaning system is no longer activated with the first stalk activation when the lights are on. The functional programming change now requires the stalk to be activated four times before headlight cleaning is activated. The change prevents automatic activation of headlight cleaning when the customer only wants to clean his/her windshield. This is normal operation and no parts should be changed.
Associated Products (24)Associated Documents - November 1, 2014•Document ID: 10148413Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE AND ENGINE COOLING:ENGINE:DIESEL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE)
- Mfr Comm. #:
- 011214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryM57 Diesel Engine Throttle Valve (for EGR): Limited Warranty Extension to 10 Years/120,000 Miles. INFORMATION BMW of North America, LLC ("BMW NA") is extending the limited warranty for the M57 diesel engine's throttle valve (for EGR) on the above-referenced vehicle to: 10 years/120,000 miles, whichever occurs first, as determined from the original in-service date. This bulletin is a notice of a "limited warranty extension." This is not a notice of a Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, BMW NA sent VIN-specific customer notification letters. A sample letter is attached. Eligible BMW Vehicles To assist you in identifying eligible vehicles, the DCSnet Warranty Vehicle Inquiry has been updated with the following "Vehicle Comment," shown below: BMW of North America, LLC has extended this vehicle's M57 diesel engine throttle valve (for EGR) limited warranty to 10 years or 120,000 miles, whichever occurs first, as determined from the original in-service date. Please see SI B01 12 14. Note: Always check the DCSnet Warranty Vehicle Inquiry "Vehicle Comments" and the "Repair History (Claims)" sections first before performing any repairs.
Associated Products (25)Associated Documents - October 1, 2014•Document ID: 10149382Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 8403014
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryiPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants
Associated Products (215)Associated Documents - October 1, 2014•Document ID: 10149381Service Bulletin/Repair InstructionsBACK OVER PREVENTION
- Mfr Comm. #:
- 660814
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummarySide View Camera Does Not Display Picture. The side view camera does not display a picture: z After engaging reverse gear z Activating the side view camera via the switch on the center console near the gear shift CAUSE z Water (moisture) entering the cable assembly, causing corrosion on the pins in the connector(s) at the camera(s) z Poor cable connection to the camera(s)
Associated Products (101)Associated Documents - October 1, 2014•Document ID: 10149379Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 651313
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryHeadunit-High: CID Is Blank and "NO SIGNAL" Is Displayed. Intermittently the Central Information Display (CID) is blank and "NO SIGNAL" is displayed on the CID. z Fault Code B7F8C3 "no response from CID (HW error: loss of CID communication)" is stored in the HU-H Note: If Fault Code E1C440 "Headunit Reset" is also stored in the HU-H, this Service Information is not effective! Follow relevant test plan using ISTA diagnosis. Software error in the HU-H
Associated Products (53)Associated Documents - October 1, 2014•Document ID: 10149375Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 620414
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryService Action: Replace Instrument Cluster. The display in the instrument cluster is inoperative.
Associated Products (20)Associated Documents - October 1, 2014•Document ID: 10149371Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 612614
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryHorn(s) Fail to Work. While trying to activate the horn, one or both horns fail to work. One or more of the following fault codes can be stored in the FEM: "8044A3 - Wiring, horn short circuit to earth" "8044A4 - Wiring, horn short circuit to positive" "8044A5 - Wiring, horn relay is defective or short circuit to positive" Water has entered the horn and caused it to fail internally (shorted out).
Associated Products (20)Associated Documents - October 1, 2014•Document ID: 10149365Service Bulletin/Repair InstructionsSTEERING
- Mfr Comm. #:
- 320314
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryPower-Assisted Steering Failure. The power-assisted steering fails with a warning lamp in the instrument cluster or a check control message in the Central Information Display. In some cases, the Dynamic Stability Control warning lamp (DSC) in the instrument cluster may also be illuminated. Failure of the power-assisted steering may be caused by various software-related issues. The following codes may be stored in the fault memory of the Electric Power Steering (EPS): Scenario 1: 0x4823E1 Scenario 2: 0x4823CB/0x4823CC Scenario 3: 0x4823D2 and/or 0x4823EC Scenario 4: 0x48239C (DSC warning lamp lights up in the instrument cluster) Scenario 5: No communication with the EPS is possible (not accessible using diagnostics) Scenario 6: 0x4823EE and 0x4823C2
Associated Products (24)Associated Documents - October 1, 2014•Document ID: 10149363Service Bulletin/Repair InstructionsSUSPENSION
- Mfr Comm. #:
- 310514
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryFront Suspension Ride Height Has Dropped. INFORMATION Damages due to outside influences are not covered under the terms of the BMW limited warranties.
Associated Products (20)Associated Documents - October 1, 2014•Document ID: 10149361Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- 280114
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryDCT Transmission: Oil Leakage Diagnosis. INFORMATION Incorrect diagnosis of DCT (Double-clutch Transmission) oil leaks may lead to unnecessary part replacements and repeat customer repair visits. When diagnosing complaints related to DCT fluid leaks, please use the attached diagnostic procedure. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment B280114_DCT_Oil_Leak_Diagnosis. [ Copyright (c)2014 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/16672.2.B28011... 12/24/2014
Associated Products (63)Associated Documents - October 1, 2014•Document ID: 10149360Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 170114
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryLow Coolant Level with No Sign of External Leaks. The Low Coolant Warning light is on and there are no signs of a visual leak. Pressure testing the cooling system may or may not show an internal leak (loss of pressure). There may also be a complaint of transmission fluid leaking from the vent on top of the transmission; poor shift quality; or a shuddering from the transmission. There is an internal failure of the automatic transmission oil cooler, allowing coolant to mix with transmission fluid. Possible faulty coolers were built between 6/6/2013 and 8/4/2013.
Associated Products (11)Associated Documents - October 1, 2014•Document ID: 10149355Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 130514
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary. INFORMATION To properly diagnose the customer's complaint, the applicable test plan for the misfire faults stored in the DME must be performed to avoid repeat repairs. If a misfire fault is not stored in the DME memory and an engine related drivability complaint is received, follow the path below to manually start the misfire test plan (AT1214_TVD4_MISFIRE_20): 1. Perform a vehicle test. 2. Select "Function Structure." 3. Select "01 Engine." 4. Select "Engine electronics MEVD." 5. Select "Misfire detection." 6. Follow the steps in the test plan and select "Basic check (start)" first. Do not select "Additional check" at this time. 7. If the result of the "Basic check" indentifies a fuel system component failure, replace the identified component. If the result of the "Basic check" test plan was inconclusive, go to step 7. After the component replacement, perform the "Basic check" portion of the test plan again to verify if the diagnosis was correct and the vehicle condition has been rectified.
Associated Products (58)Associated Documents - October 1, 2014•Document ID: 10149353Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 130114
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryN47T and N57T Diesels with SCR Efficiency Faults Stored. A. The Service Engine Soon lamp is on (MIL) with either or both of the following SCR efficiency faults stored in the DDE: 26F500 - SCR system, efficiency: Efficiency too low 26F600 - SCR system, efficiency: Efficiency too low B. In addition, a Check Control message of "Incorrect diesel exhaust fluid" may be displayed with "no start scenario countdown" active. This would cause any of the following additional faults to be stored, depending on the SCR system status at the time. 2C4E00 - SCR system: System error and poor urea/water mixture quality detected 26FD00 - Reducing agent metering, long-term adaptation: Adaptation value too high 29FB00 - SCR system, warning and deactivation scenario: Warning level 1 29FC00 - SCR system, warning and deactivation scenario: Warning level 2 CAUSE Unfavorable DDE software
Associated Products (20)Associated Documents - October 1, 2014•Document ID: 10149351Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 122914
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryReduced Engine Performance. When driving with high outside ambient temperatures, repeated stop and go, or high-load operation over longer distances, the engine performance can be reduced. The air-conditioning system blower output may also be reduced, and in some circumstances, the compressor is switched off. One or both of the following faults are stored in the DME: 1A2108: Electric fan, self-diagnosis, interval stage 1: Minor fan fault 241400: Electric fan, diagnosis feedback 1: Fan slightly stiff The Service Engine Soon lamp (MIL) would not be illuminated in these situations. 1. A DME software error in the control of the 600W electric fan over-boost or high speed function 2. The electric cooling fan design was not robust enough for continuous over-boost or high-speed operation.
Associated Products (18)Associated Documents