BMW 328i Complaints

2,583 consumer complaints on file.

#11751109July 17, 2026
ENGINE
I brought my vehicle to an authorized dealer for three open safety recalls. Two were performed at no charge. The third, the VANOS adjustment unit screw connection recall, was not performed. The dealer stated in writing on the repair order that the vehicle has a broken valve cover bolt, that the valve cover will not seal properly, and that a new valve cover is recommended to complete the recall. They quoted $1,077.43 for a valve cover as a customer-pay repair and stated the recall could not be completed until that was done. I declined the valve cover. The recall was not performed. The bolt is not broken and the valve cover is not broken. The threads in the cylinder head bolt boss are stripped, and a larger bolt was installed that holds. There is no oil leak. A new valve cover would thread into the same stripped hole in the cylinder head and would not repair the damaged threads. The dealer's proposed repair does not address the condition they described. The manufacturer's dealer bulletin for this recall lists a cylinder head cover profile seal as a recall part and does not list a valve cover in any parts list. The remedy requires removing the cylinder head cover regardless. I left without signing the repair order. The recall remains open. I am reporting that a free safety recall remedy was conditioned on a customer-pay repair. The dealer could have performed the recall, documented the pre-existing thread damage on the repair order, noted that the customer was advised and declined the valve cover, and disclaimed responsibility for any future seepage at the cover. I would have accepted that. Instead they performed neither the recall nor any repair, and left a federal safety recall open.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11751142July 17, 2026
ENGINE, FUEL/PROPULSION SYSTEM, ELECTRICAL SYSTEM
The engine intake tract, PCV infrastructure, and the main lower engine wiring harness loom failed due to improper reassembly during Federal Safety Recall 24V-608. The technician left the main intake coupler completely loose and spinning freely by hand, and left the MAF sensor crooked. This introduced a massive unmetered air leak and severe vacuum leaks. Simultaneously, the technician over-tensioned, pinched, or damaged the Cylinder 2 wiring loom components. The vehicle is currently parked dead and untouched at my residence, and it is 100% available for immediate federal or corporate inspection.The unsealed intake tract and damaged wiring harness caused the engine to run dangerously lean at highway speeds. This resulted in sudden, violent engine shuttering, rapid deceleration, severe mechanical engine knocking, and a terminal Cylinder 2 misfire. This component failure caused an immediate loss of vehicle propulsion on a high-speed public highway, creating an extreme risk of a high-speed collision and leaving the vehicle completely disabled. The issue has not yet been physically inspected by a third party because the vehicle is unsafe to drive. I went to the originating dealer (BMW of Henderson) in person on July 16, 2026, to coordinate a safety re-inspection under an active BMW North America Corporate Case. Dealership management actively obstructed the safety process, gave technically impossible justifications regarding the recall execution, and flatly refused to dispatch a complimentary flatbed tow. They attempted to hold the safety re-inspection hostage behind out-of-pocket customer towing costs and upfront retail diagnostic fees. There were 0 mechanical warnings or symptoms prior to the recall. The vehicle was meticulously maintained with 5,000-mile oil changes and a perfectly tight timing chain. The severe drivetrain malfunction warnings, violent front-end shaking, and terminal engine knocking appeared after picking up my car.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11750751July 16, 2026
ENGINE AND ENGINE COOLING, ELECTRICAL SYSTEM
The contact owns a 2015 BMW 328I. The contact stated that while driving at 40 MPH, the vehicle caught on fire. The fire originated in the engine compartment. There were no warning lights illuminated. The driver was able to extinguish the fire. The vehicle was towed to the residence and was then towed to an independent mechanic, but the vehicle was not diagnosed or repaired. The vehicle was towed to the local dealer, where it was diagnosed with an electrical short circuit in the front water pump connector. The vehicle was not repaired. The contact associated the failure with NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System). The manufacturer was notified of the failure, and a claim was opened. The failure mileage was approximately 110,000.
Crash:
No
Fire:
Yes
Injuries:
0
Deaths:
0
#11748792July 7, 2026
POWER TRAIN, ENGINE
Engine oil pressure light came on and then the driver train malfunction light. Car at 113k miles and upon checking the timing chain was damage and now engine locked
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11746698June 26, 2026
ELECTRICAL SYSTEM
The vehicle constantly and increasingly exhibits the symptoms described in RECALL CAMPAIGN 13V-044: REPAIR BATTERY POSITIVE CABLE, dated XXX , i.e., various electrical malfunctions, including flickering of the instrument cluster, and brief loss of engine power. However, VIN [XXX] is NOT included in this campaign. It appears that the next possibility, even though deemed "extremely isolated" by the recall, is that "the engine may shut off while driving, which leads to a loss of power steering assistance." BMW and NHTSA each state that the other is responsible for including VINs in a recall, yet I am the one at risk of crash. Do I need to seek legal action against both BMW and NHTSA to determine who is responsible for adding the VIN to the recall so BMW can eventually reimburse me for the needed repairs? INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11742298June 5, 2026
ENGINE
I am filing a formal complaint against BMW Seattle for violating federal recall remedy mandates under 49 U.S.C. Chapter 301. The vehicle was delivered for mandatory safety recall 23V-707 after an on-road mechanical shear of the covered VANOS bolts. The dealer has created illegal commercial barriers and failed to fully execute the federal remedy. First, the service department issued a written estimate for $4,405.67, claiming the CAS module and locks failed and required replacement to resolve a no-start condition. I challenged the repair on technical grounds and authorized a new battery and valid key only, the dealer admitted in writing that the electrical sync restored seamlessly and the engine started. They attempted to extract thousands for a functioning module before verifying the recall. Second, the VANOS bolts sheared resulting in certain valve-piston contact. The dealer claimed the engine passed a compression check but refused to provide raw ISTA diagnostic logs to verify this safety threshold. Instead, they demanded an additional out-of-pocket fee of $669.60 to re-perform a test they claimed to have completed, creating a commercial barrier to basic remedy verification. Third, the dealer demanded $2,136.69 to replace a compromised valve cover and PCV valve which functioned without issue pre-failure. Valve cover removal is required for vanos repair and requiring consumer expense for mandatory safety repair is legally prohibited. Indeed, Under BMW SIB 11 09 23, collateral damage must be routed through corporate TSARA, not the consumer. Fourth, the steel VANOS bolt heads sheared completely off. The official remedy mandates dropping the oil pan to locate and remove these fragments to prevent total oil pressure loss. Despite my repeated requests for verification of removal, nothing was provided, the car was inoperable, and I was advised that the recall repair was complete and the vehicle was in outdoor fenced lot awaiting arrangements for removal.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11741411June 1, 2026
ENGINE
On [XXX], my 2015 BMW 328i xDrive (VIN: [XXX] , N20 engine, 124,250 miles) suffered a catastrophic engine failure while in operation. Component/System Failed: The timing chain guides and oil pump drive chain module failed. The plastic timing chain guide broke apart inside the engine. The vehicle was salvaged and is no longer available for inspection. Safety Risk: The oil pressure warning illuminated suddenly while driving at highway speed with no prior warning. Sudden loss of oil pressure and engine power while operating a vehicle at speed creates a significant risk of accident, loss of vehicle control, and injury to the driver and others on the road. Confirmed by Service Center: BMW of Springfield, New Jersey performed a formal diagnostic confirming timing chain guide failure and oil pump drive chain failure. A BMW mechanic performed a scope inspection on April 3, 2026 visually confirming the broken plastic timing chain guide. Repair estimate: $7,191.42. Inspected by Others: The vehicle was inspected solely by BMW of Springfield. No police, insurance, or manufacturer representatives conducted a separate inspection. The failure mode is consistent with the defect acknowledged in BMW NA Technical Service Bulletin SI B11 03 17 and federal class action [XXX] v. BMW of North America, LLC (D.N.J. [XXX]). Warning Symptoms: The only warning was a sudden oil pressure warning message on the dashboard immediately before failure. Prior to that moment the vehicle operated normally with no unusual noises, no warning lights, and no fluid leaks. There were no gradual symptoms or prior indications of impending failure. Vehicle was declared a total economic loss and salvaged for $1,650.00. No injuries occurred. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11741157May 31, 2026
ENGINE
I was driving in the highway at 65MPH, I heard an audible tone. I looked at speedometer and had a message to to press unlock button to switch gears. Then my engine light came on and was steady. My car went into neutral while driving at 65 mph. Thank god I was able to pull to side. I tried to put back into drive or reverse and no response. It did allow me place in park. It would not start. I had it towed to a BMW service center and they said my engine failed internally.. while driving.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11740338May 27, 2026
ELECTRICAL SYSTEM, EXTERIOR LIGHTING, FORWARD COLLISION AVOIDANCE: WARNINGS
i went online because i was having troubles with my vehicle battery alternator and other electronics , i found out other bmws with the same symptoms as my car led to having a bad footwell module , currently interior lights work when they want to if any constant battery dying from lights not turning off none of the parking sesnors work no back up camera the rear windows do not work some times the power mirrors work , i have had the vehicle tested with a new alternator and battery each window motor works its the footwell module but i noticed that the extended warranty is for 2014 and older models sadly it also effects the 2015 models as well
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11737824May 14, 2026
ENGINE, FUEL/PROPULSION SYSTEM, EXTERIOR LIGHTING
I Was In My Vehicle Parked Up On January 1st 2026 And The Vehicle Caught On Fire While I Was Inside Of It,The Fire Started From The Right Side Of The Car And Flamed Up Everything,The Car Had A Check Engine Light On And A Lightning System Issue Was Popping Up On The Dash Right Before This Situation Accord I Did Research And Found That The Cause Of The Fire Is Related To NHTSA Recall 24V-608 (Water Pump/Connector Fire Risk).
Crash:
No
Fire:
Yes
Injuries:
0
Deaths:
0
#11736030May 6, 2026
ENGINE AND ENGINE COOLING, ELECTRICAL SYSTEM
The contact owns a 2015 BMW 328I. The contact received notification of NHTSA Campaign Number: 24V608000 ( ENGINE AND ENGINE COOLING, ELECTRICAL SYSTEM). The contact stated that while driving at an undisclosed speed, the message "turn off engine and do not open hood" was displayed on the instrument panel. The contact was able to pull to the side of the road and checked the water reservoir and noticed it was low. The contact filled up the reservoir with water and waited a few minutes. Afterward, the vehicle drove normal. The failure persisted. The vehicle was towed to the dealer. However, it was not diagnosed. The dealer informed the contact that per the recall the remedy was to install a protective shield. The contact asked the dealer to replace the engine coolant pump and connector. However, the dealer refused. The vehicle remained at the dealer unrepaired. The manufacturer was not notified of the failure. The failure mileage was approximately 100,000.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11734197April 27, 2026
SERVICE BRAKES
Parking brake retainer Clio failed in highway causing car to lose control in the highway.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11733199April 23, 2026
ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER
Odometer Fraud. The contact purchased a 2010 BMW 328I. It was discovered that there was a mileage discrepancy. The vehicle was a private sale. At the time of purchase, the vehicle mileage was 107,414. The contact stated that, while driving 25 MPH over a pothole, several systems in the vehicle unexpectedly reset; however, the speedometer had not reset. The contact stated that the vehicle had not been driven a whole lot. The mileage was reset to approximately 120,000 miles. The contact attempted to retrieve a Carfax Report for the vehicle and became aware that the most recent information on the VIN was posted by the seller. The contact called the seller. No other agencies were contacted.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11733200April 23, 2026
ENGINE AND ENGINE COOLING, AIR BAGS, SERVICE BRAKES, HYDRAULIC
The contact owns a 2010 BMW 328I. The contact received notifications of NHTSA Campaign Numbers: 24V513000 (Air Bags), 23V707000 (Engine and Engine Cooling), and 22V119000 (Engine and Engine Cooling); however, the parts to do the recall repairs were unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repairs. The contact stated that while accelerating from the vehicle idling, and turning left or right, the transmission hesitated before shifting hard. Occasionally, while attempting to accelerate, the vehicle unintendedly decelerated, hesitated, and failed to accelerate as intended. The vehicle intermittently stalled, and the contact would release the accelerator pedal, depress the brake pedal, and allow the steering wheel failure to self-correct. The failures became more persistent. The ABS, check engine, X-Drive Fluid, ESC, and TPMS warning lights were illuminated. The contact stated that after adding fluid, the failure persisted. The driver's front seat air bag failed to activate intermittently while the driver's seat was occupied. The heating system occasionally failed to operate. The contact became aware of fluid under the vehicle. The dealer was contacted, but the vehicle was not repaired. The vehicle was taken to a certified mechanic to be diagnosed, and the air bag and traction control warning lights were illuminated. The certified mechanic recommended an oil change because the engine oil was dirty. The vehicle was not repaired. The contact radiator was repaired to resolve the failure with the heating system, but the failures persisted. The manufacturer was not informed of the failures. The failure mileage was unknown.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11733290April 23, 2026
ENGINE
The contact owns a 2010 BMW 328I. The contact stated that the vehicle was taken to the dealer for an unknown recall repair, but the vehicle experienced the failure after the repair. The contact stated that while driving at an undisclosed speed, the vehicle lost automotive power, and the check engine warning light was illuminated. The vehicle was taken back to the dealer, where it was initially diagnosed that the oil cap had failed. The dealer later informed the contact that the camshaft solenoid had failed and needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure. The approximate failure mileage was 110,000.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11727018March 25, 2026
ENGINE AND ENGINE COOLING
The contact owns a 2011 BMW 328I. The contact stated that upon starting the vehicle, the low oil pressure warning light illuminated, and the vehicle stalled. The vehicle was towed to an independent mechanic, where it was diagnosed, and determined that the VANOS bolts had failed and needed to be replaced. The vehicle was not repaired due to the cost. The contact related the failure to TSB Number: SIB 11 04 14. The manufacturer was notified of the failure and informed the contact that the vehicle was covered under the TSB. The failure mileage was approximately 157,637.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11726074March 21, 2026
ENGINE
So, the N20 2.0L motors are known to have prematurely failing plastic chain guides and a weak hydraulic tensioner, leading to whine, rattles, and potential engine failure. BMW improved the issue in the 2015 or newer models which have more robust timing chain guides and Tensioners. The fix involves replacing the entire timing chain assembly (guides, chain, tensioner) with updated, more durable parts and cleaning the oil pump/pan of debris. Which the 2015 and newer models have this fix. 2014 and older models with the N20 suffer from failing parts due to a design flaw. Since the The BMW N20 engine (2012–early 2015 328i) does suffer from premature timing chain guide failure, leading to oil pump failure and catastrophic engine failure. There should be a recall with these older models. And there should be a fix for them. BMW design this motor and the only remedy the issue in the newer models 2015 or newer. So anyone that doesn't have a 2015. Their N20 is basically a ticking time bomb.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11723979March 12, 2026
ENGINE, POWER TRAIN
2013 BMW 328i, N20 engine. Timing chain guide assembly and oil pump drive chain failed catastrophically. Vehicle is available for inspection, however the authorized BMW dealership has already made clear they will accept no responsibility, and I would bear the expense of towing it two hours to their facility. The failure is a known issue with a class action case, but BMW took no responsibility, and falsified information stating the vehicle showed no signs of an issue when I brought my vehicle in for inspection. Eighteen months before failure, steam came from the engine compartment on a humid day, later connected to the water pump electrical connector recall. Following this, the vehicle ran consistently hotter than normal and lost noticeable power. Twelve months before failure, an intermittent oil pressure warning began triggering under load at highway speeds, particularly on inclines above 70mph. I brought the vehicle to Sandia BMW in Albuquerque, NM and reported all symptoms when I was contacted by them for the recall. The service advisor falsely claimed elevated operating temperature was optimal, suspected a faulty sensor, and returned the vehicle without offering further diagnosis or making me aware of the impending issue, all classic signs of the engine faults. Eight weeks later, the oil pressure light activated on a highway, followed immediately by a drivetrain malfunction warning, a violent grinding sound, and complete loss of power. The vehicle was towed and has not restarted since. I contacted BMW of North America's recall line. A case was opened and an advocate stated BMW would accept no responsibility because the class action was closed and I'mpast 70K miles. I raised the dealership's direct culpability. The advocate stated a dealership representative would contact me. No call was ever received. This failure is consistent with BMW Service Bulletin SI B11 03 17. A engine safety recall is warranted regardless of age to protect the public.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11723902March 12, 2026
ENGINE AND ENGINE COOLING
The contact owns a 2010 BMW 328I. The contact stated that when the vehicle was started, the vehicle was idling rough and occasionally, the vehicle lost automotive power. The contact stated that the failure was intermittent but was more frequent. The contact stated that the check engine warning light was illuminated. While the vehicle was idling, the RPM was fluctuating between 800 - 1,000 RPM. The vehicle was taken to an independent mechanic, who diagnosed the vehicle and determined that there was a failure with the VANOS valve timing system. The contact was informed that the VANOS valve timing system needed to be replaced. The contact researched online and related the failure to NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling); however, the VIN was not included in the recall. The vehicle was not repaired. The manufacturer was informed of the failure and advised the contact that recalls were VIN-specific and that the VIN was not included in the recall. The failure mileage was approximately 130,000.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11723477March 11, 2026
ENGINE
Vehicle is under Recall 24V-608 for a fire risk. The vehicle has suffered the exact failure described (Overheating, Limp Mode, and Smoke/Thermal Event). Dealership (BMW of Pleasant Grove Utah) is refusing to replace the failed water pump, offering only a 'protective shield' which does not fix the current failure. This is a failure to provide a free and effective remedy for a known safety defect. A code was discovered when the senior advisor at this location ran the scanner, and displayed a "coolant pump switch-off due to locking" which the senior advisor tried to deflect as a physical object blocking the pump or some other mysterious issue. The issue was confirmed at a reputable maintenance shop earlier in the day before towing to BMW dealership. The senior advisor at BMW of Pleasant Grove is attempting to put me back in the road in a high safety risk vehicle.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0

← Back to BMW 328i