Mazda Mazda6 Service Bulletins

1,417 manufacturer communications on file.

May 8, 2018•Document ID: 10142516
Service Bulletin/Repair Instructions
ENGINE
Mfr Comm. #:
01-012-18-3474
Date Added:
July 2, 2018
Manufacturer:
MAZDA
Summary
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input. As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display "F0-002" during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km). Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.
Associated Products (25)
2018 Mazda CX-3 2018 Mazda CX-5 2018 Mazda CX-9 2018 Mazda Mazda3 2018 Mazda Mazda6 2018 Mazda MX-5 2017 Mazda CX-3 2017 Mazda CX-5 2017 Mazda CX-9 2017 Mazda Mazda3 2017 Mazda Mazda6 2017 Mazda MX-5 2016 Mazda CX-3 2016 Mazda CX-5 2016 Mazda CX-9 2016 Mazda Mazda3 2016 Mazda Mazda6 2016 Mazda MX-5 2015 Mazda CX-5 2015 Mazda Mazda3+ 5 more
Associated Documents
- Download MC-10142516-0001.pdf↗
May 7, 2018•Document ID: 10142518
Service Bulletin/Repair Instructions
TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS
Mfr Comm. #:
02-009-18-3472
Date Added:
July 2, 2018
Manufacturer:
MAZDA
Summary
Customer complaints have been reported where the TPMS warning light is unnecessarily illuminated because the TPMS initialization was not performed correctly before customer delivery.TPMS INITIALIZATION PROCESS: When any of the services below is performed, BE SURE TO INITIALIZE THE TPMS BEFORE DRIVING THE VEHICLE by pushing and holding the TPMS Set Switch on the dash until the TPMS warning light flashes two times and the warning beep sounds once. The TPMS must be initialized in the following cases: 1. Tire pressures have been adjusted in one or more tires. 2. Tires have been rotated. 3. Tires or wheels have been replaced. 4. The vehicle's battery cable has been disconnected for any reason. 5. The vehicle's battery has been discharged. 6. The DSC HU/CM connector has been disconnected for any reason.
Associated Products (20)
2018 Mazda CX-3 2018 Mazda Mazda3 2017 Mazda CX-3 2017 Mazda CX-9 2017 Mazda Mazda3 2017 Mazda Mazda6 2017 Mazda MX-5 2016 Mazda CX-3 2016 Mazda CX-5 2016 Mazda CX-9 2016 Mazda Mazda3 2016 Mazda Mazda6 2016 Mazda MX-5 2015 Mazda CX-5 2015 Mazda Mazda3 2015 Mazda Mazda6 2014 Mazda CX-5 2014 Mazda Mazda3 2014 Mazda Mazda6 2013 Mazda CX-5
Associated Documents
- Download MC-10142518-0001.pdf↗
May 4, 2018•Document ID: 10142532
Service Bulletin/Repair Instructions
EQUIPMENT; EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM:SOFTWARE; ELECTRICAL SYSTEM
Mfr Comm. #:
SA-025-18
Date Added:
July 2, 2018
Manufacturer:
MAZDA
Summary
When performing the MGSS Workshop Manual 360° View Monitor System Aiming Procedure, M-MDS may show error message "Procedure unsuccessful". This may be caused by light glare on the SST.
Associated Products (1)
2018 Mazda Mazda6
Associated Documents
- Download MC-10142532-0001.pdf↗
May 3, 2018•Document ID: 10142531
Service Bulletin/Repair Instructions
STRUCTURE:BODY:HOOD
Mfr Comm. #:
SA-024-18
Date Added:
July 2, 2018
Manufacturer:
MAZDA
Summary
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
Associated Products (26)
2018 Mazda CX-3 2018 Mazda CX-5 2018 Mazda CX-9 2018 Mazda Mazda3 2018 Mazda Mazda6 2018 Mazda MX-5 2017 Mazda CX-3 2017 Mazda CX-5 2017 Mazda CX-9 2017 Mazda Mazda3 2017 Mazda Mazda6 2017 Mazda MX-5 2016 Mazda CX-3 2016 Mazda CX-5 2016 Mazda CX-9 2016 Mazda Mazda3 2016 Mazda Mazda6 2016 Mazda MX-5 2015 Mazda CX-5 2015 Mazda Mazda3+ 6 more
Associated Documents
- Download MC-10142531-0001.pdf↗
May 1, 2018•Document ID: 10142530
Service Bulletin/Repair Instructions
LANE DEPARTURE: WARNING; EXTERIOR LIGHTING:HEADLIGHTS:HIGH/LOW BEAM DIMMER SWITCH
Mfr Comm. #:
SA-023-18
Date Added:
July 2, 2018
Manufacturer:
MAZDA
Summary
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details.
Associated Products (22)
2018 Mazda CX-3 2018 Mazda CX-5 2018 Mazda CX-9 2018 Mazda Mazda3 2018 Mazda Mazda6 2018 Mazda MX-5 2017 Mazda CX-3 2017 Mazda CX-5 2017 Mazda CX-9 2017 Mazda Mazda3 2017 Mazda Mazda6 2017 Mazda MX-5 2016 Mazda CX-3 2016 Mazda CX-5 2016 Mazda CX-9 2016 Mazda Mazda3 2016 Mazda Mazda6 2016 Mazda MX-5 2015 Mazda Mazda3 2015 Mazda Mazda6+ 2 more
Associated Documents
- Download MC-10142530-0001.pdf↗
April 30, 2018•Document ID: 10136768
Service Bulletin/Repair Instructions
ELECTRICAL SYSTEM
Mfr Comm. #:
SA-021-18
Date Added:
May 14, 2018
Manufacturer:
MAZDA
Summary
MAZDA CONNECT SOFTWARE VERSION 59.00.545 AVAILABLE. An update to the MAZDA CONNECT system is now available for download from the Mazda Global Service Support (MGSS) system. The new version number is 59.00.545. Mazda Requests the MAZDA CONNECT system be updated on all new vehicle inventory and CPO vehicles ASAP. For CPO inventory vehicles out of warranty, for this software release only, you may use Dealer Self Authorization or DSM goodwill. Click on "Infotainment", then "MAZDA CONNECT Updates" to download it and update your USB drives. Also make sure to select "All Files" for "Save as type:". If left as "Compressed (zipped) Folder," the file will be saved as a ".zip" no matter what you use as an extension. DO NOT shut off the ignition or let it shut off at any time during the entire MAZDA CONNECT update process (both Failsafe and Reinstall), otherwise the CMU may be damaged and need to be replaced.
Associated Products (6)
2018 Mazda CX-3 2018 Mazda CX-5 2018 Mazda CX-9 2018 Mazda Mazda3 2018 Mazda Mazda6 2018 Mazda MX-5
Associated Documents
- Download MC-10136768-0001.pdf↗
April 27, 2018•Document ID: 10136776
Service Bulletin/Repair Instructions
SERVICE BRAKES
Mfr Comm. #:
04-004-18-3468
Date Added:
May 14, 2018
Manufacturer:
MAZDA
Summary
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
Associated Products (96)
2018 Mazda CX-3 2018 Mazda CX-5 2018 Mazda CX-9 2018 Mazda Mazda3 2018 Mazda Mazda6 2018 Mazda MX-5 2017 Mazda CX-3 2017 Mazda CX-5 2017 Mazda CX-9 2017 Mazda Mazda3 2017 Mazda Mazda6 2017 Mazda MX-5 2016 Mazda CX-3 2016 Mazda CX-5 2016 Mazda CX-9 2016 Mazda Mazda2 2016 Mazda Mazda3 2016 Mazda Mazda5 2016 Mazda Mazda6 2016 Mazda MX-5+ 76 more
Associated Documents
- Download MC-10136776-0001.pdf↗
April 27, 2018•Document ID: 10136774
Service Bulletin/Repair Instructions
WHEELS
Mfr Comm. #:
02-008-18-3467
Date Added:
May 14, 2018
Manufacturer:
MAZDA
Summary
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.
Associated Products (95)
2018 Mazda CX-3 2018 Mazda CX-5 2018 Mazda CX-9 2018 Mazda Mazda3 2018 Mazda Mazda6 2018 Mazda MX-5 2017 Mazda CX-3 2017 Mazda CX-5 2017 Mazda CX-9 2017 Mazda Mazda3 2017 Mazda Mazda6 2017 Mazda MX-5 2016 Mazda CX-3 2016 Mazda CX-5 2016 Mazda CX-9 2016 Mazda Mazda2 2016 Mazda Mazda3 2016 Mazda Mazda5 2016 Mazda Mazda6 2016 Mazda MX-5+ 75 more
Associated Documents
- Download MC-10136774-0001.pdf↗
April 23, 2018•Document ID: 10136765
Service Bulletin/Repair Instructions
EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
Mfr Comm. #:
SA-012-18
Date Added:
May 14, 2018
Manufacturer:
MAZDA
Summary
Some 2018 vehicles built after January 1, 2018 and equipped with Navigation may exhibit one of these concerns after the user inputs an address: A screen pops up that says "House number not found." After the user selects OK, the system finds the address or a nearby address.Instead of finding the correct address number the system adds a digit to the end of the number. Example: You enter 151 and the system comes back with 1510, 1511, 1515, 1516, etc. This only occurs with MAZDA CONNECT software version 59.00.532 or 59.00.540, which started being installed into vehicles in January 2018. The concern can be eliminated by installing MAZDA CONNECT software version 59.00.545 now available on MGSS.
Associated Products (6)
2018 Mazda CX-3 2018 Mazda CX-5 2018 Mazda CX-9 2018 Mazda Mazda3 2018 Mazda Mazda6 2018 Mazda MX-5
Associated Documents
- Download MC-10136765-0001.pdf↗
April 16, 2018•Document ID: 10136782
Service Bulletin/Repair Instructions
EQUIPMENT:APPLIANCE:AIR CONDITIONER
Mfr Comm. #:
07-002-18-3432
Date Added:
May 14, 2018
Manufacturer:
MAZDA
Summary
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/Cevaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. "Mazda Air Cooling Coil Coating" is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers. This treatment provides a durable coating that will aid to prevent biological reactions that lead to odorconcerns. It is applied to the evaporator in a misted form that is introduced by way of the cabin air filter, the re-circulate door, the blower motor resistor access, or the blower motor air intake. Proper application requires the evaporator surface to be: Relatively clean and free of leaves, dust build-up and debris. Thoroughly dried, and the product cured onto it after application. NOTE: Keep the cooling unit dry by leaving the blower fan ON (at least on low), even if the A/C is not being used. In low humidity (dry) conditions, keep the ventilation system in the "FRESH" mode all the time, or as much as possible. In high humidity conditions, or if the air has a lot of dust or pollen, keep the system in the "RECIRCULATION" mode. A few minutes before reaching a destination, turn the A/C OFF, but leave the blower fan ON. This stops the accumulation of condensation on the evaporator/cooling unit, and it helps dry the inside of the cooling unit. A/C odor is not unique to Mazda vehicles as it will occur in other makes and models. To minimize A/C odor, suggest the following to the customers.
Associated Products (98)
2018 Mazda CX-5 2018 Mazda CX-9 2018 Mazda Mazda3 2018 Mazda Mazda6 2018 Mazda MX-5 2017 Mazda CX-5 2017 Mazda CX-9 2017 Mazda Mazda3 2017 Mazda Mazda6 2017 Mazda MX-5 2016 Mazda CX-5 2016 Mazda CX-9 2016 Mazda Mazda3 2016 Mazda Mazda6 2016 Mazda MX-5 2015 Mazda CX-5 2015 Mazda CX-9 2015 Mazda Mazda3 2015 Mazda Mazda5 2015 Mazda Mazda6+ 78 more
Associated Documents
- Download MC-10136782-0001.pdf↗
April 16, 2018•Document ID: 10136780
Service Bulletin/Repair Instructions
ENGINE AND ENGINE COOLING
Mfr Comm. #:
05-004-18-3466
Date Added:
May 14, 2018
Manufacturer:
MAZDA
Summary
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on P0877:00 - Oil pressure switch No. 4 (oil pressure switch B) stuck on P0780:00 - Gear shifting malfunction P1738:00 Automatic transaxle internal malfunction This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. NOTE: If the vehicle also has a delayed engagement concern, this TSB is not applicable. Refer to MGSS online for proper diagnosis and repair procedure.
Associated Products (24)
2018 Mazda CX-3 2018 Mazda CX-5 2018 Mazda CX-9 2018 Mazda Mazda3 2018 Mazda Mazda6 2017 Mazda CX-3 2017 Mazda CX-5 2017 Mazda CX-9 2017 Mazda Mazda3 2017 Mazda Mazda6 2016 Mazda CX-3 2016 Mazda CX-5 2016 Mazda CX-9 2016 Mazda Mazda3 2016 Mazda Mazda6 2015 Mazda CX-5 2015 Mazda Mazda3 2015 Mazda Mazda6 2014 Mazda CX-5 2014 Mazda Mazda3+ 4 more
Associated Documents
- Download MC-10136780-0001.pdf↗
April 13, 2018•Document ID: 10136769
Service Bulletin/Repair Instructions
EQUIPMENT
Mfr Comm. #:
00-002-18-3463
Date Added:
May 14, 2018
Manufacturer:
MAZDA
Summary
In support of the new Mazda6 Signature model, Mazda will make available for loan on a "as-needed" basis, a Special Service Tool (SST) to allow for the aiming of the 360 Degree Camera System. Please follow the aiming instructions on MGSS (360° VIEW MONITOR SYSTEM AIMING). The tool is available to order as a loaner on Mazda e-Store.
Associated Products (1)
2018 Mazda Mazda6
Associated Documents
- Download MC-10136769-0001.pdf↗
April 12, 2018•Document ID: 10136779
Service Bulletin/Repair Instructions
POWER TRAIN
Mfr Comm. #:
05-003-18-3460
Date Added:
May 14, 2018
Manufacturer:
MAZDA
Summary
Some customers who drive at elevations higher than 3,300 ft (1,000 m) may complain of a shift shock felt when shifting into 3rd, 5th and/or Reverse with no AT related DTCs stored. The symptom can be temporarily repaired using the AT initial learning procedure, but may recur after multiple driving cycles. Applicable situations: Shifting up: 2-3 or 4-5 Shifting down: 4-3 or 6-5 NOTE: Shifting from 2-3 or 4-3 is more likely to be felt due to the gear ratio. Shifting into Reverse: D-R, N-R or P-R Improper control logic of the TCM may cause improper learning of R-3-5 brake engaging speed when the vehicle is driven at high elevations. To correct this issue, the control logic of the TCM has been modified.
Associated Products (4)
2018 Mazda CX-3 2018 Mazda Mazda3 2017 Mazda Mazda3 2017 Mazda Mazda6
Associated Documents
- Download MC-10136779-0001.pdf↗
April 10, 2018•Document ID: 10136785
Service Bulletin/Repair Instructions
ELECTRICAL SYSTEM
Mfr Comm. #:
09-008-18-3416a
Date Added:
May 14, 2018
Manufacturer:
MAZDA
Summary
Some vehicles may exhibit the active driving display opening/closing improperly as described below: It does not open or close when the ignition is turned ON or OFF. The display operation does not fully open/close. It closes and then opens by itself while the vehicle is moving. This concern may be caused by voltage fluctuation to the active driving display which activates pinching detection.
Associated Products (5)
2016 Mazda CX-3 2016 Mazda Mazda3 2016 Mazda Mazda6 2015 Mazda Mazda3 2014 Mazda Mazda3
Associated Documents
- Download MC-10136785-0001.pdf↗
April 5, 2018•Document ID: 10136788
Service Bulletin/Repair Instructions
STRUCTURE:BODY:HOOD; STRUCTURE:BODY:ROOF AND PILLARS; STRUCTURE:BODY:TRUNK LID
Mfr Comm. #:
09-021-18-3459
Date Added:
May 14, 2018
Manufacturer:
MAZDA
Summary
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).
Associated Products (17)
2018 Mazda CX-3 2018 Mazda CX-5 2018 Mazda CX-9 2018 Mazda Mazda3 2018 Mazda Mazda6 2017 Mazda CX-3 2017 Mazda CX-5 2017 Mazda CX-9 2017 Mazda Mazda3 2017 Mazda Mazda6 2017 Mazda MX-5 2016 Mazda CX-3 2016 Mazda CX-5 2016 Mazda CX-9 2016 Mazda Mazda3 2016 Mazda Mazda6 2016 Mazda MX-5
Associated Documents
- Download MC-10136788-0001.pdf↗
April 5, 2018•Document ID: 10136787
Service Bulletin/Repair Instructions
EQUIPMENT:ELECTRICAL
Mfr Comm. #:
09-020-18-3458
Date Added:
May 14, 2018
Manufacturer:
MAZDA
Summary
Some vehicles may exhibit BLUETOOTH® hands-free and/or text messaging related concerns. To improve the handling of BLUETOOTH® hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.
Associated Products (65)
2018 Mazda CX-3 2018 Mazda CX-5 2018 Mazda CX-9 2018 Mazda Mazda3 2018 Mazda Mazda6 2018 Mazda MX-5 2017 Mazda CX-3 2017 Mazda CX-5 2017 Mazda CX-9 2017 Mazda Mazda3 2017 Mazda Mazda6 2017 Mazda MX-5 2016 Mazda CX-3 2016 Mazda CX-5 2016 Mazda CX-9 2016 Mazda Mazda3 2016 Mazda Mazda6 2016 Mazda MX-5 2015 Mazda CX-5 2015 Mazda CX-9+ 45 more
Associated Documents
- Download MC-10136787-0001.pdf↗
April 5, 2018•Document ID: 10136784
Service Bulletin/Repair Instructions
AIR BAGS
Mfr Comm. #:
08-001-18-3457
Date Added:
May 14, 2018
Manufacturer:
MAZDA
Summary
This information is provided to help address Passenger Airbag Deactivation (PAD) Indicator illumination concerns during vehicle service.
Associated Products (93)
2018 Mazda CX-3 2018 Mazda CX-5 2018 Mazda CX-9 2018 Mazda Mazda3 2018 Mazda Mazda6 2018 Mazda MX-5 2017 Mazda CX-3 2017 Mazda CX-5 2017 Mazda CX-9 2017 Mazda Mazda3 2017 Mazda Mazda6 2017 Mazda MX-5 2016 Mazda CX-3 2016 Mazda CX-5 2016 Mazda CX-9 2016 Mazda Mazda2 2016 Mazda Mazda3 2016 Mazda Mazda5 2016 Mazda Mazda6 2016 Mazda MX-5+ 73 more
Associated Documents
- Download MC-10136784-0001.pdf↗
April 5, 2018•Document ID: 10136772
Service Bulletin/Repair Instructions
EQUIPMENT
Mfr Comm. #:
01-011-18-3456
Date Added:
May 14, 2018
Manufacturer:
MAZDA
Summary
The vehicles listed above are equipped with a push button start/stop ignition system. Unlike previous Mazdamodels, there is no key cylinder on the steering column. Therefore, the engine cannot be started with theauxiliary key if the room fuse is removed or if the transmitter battery is dead.NOTE: The auxiliary key can only be used to lock or unlock the doors. It cannot be used to start the engine. Two transmitters are placed in a vinyl bag and stored in the center console cup holder. Since the room fuse is not installed during vehicle assembly, a new procedure is required to start the engine. Refer to "Engine Start Procedure" below.
Associated Products (25)
2018 Mazda CX-3 2018 Mazda CX-5 2018 Mazda CX-9 2018 Mazda Mazda3 2018 Mazda Mazda6 2018 Mazda MX-5 2017 Mazda CX-3 2017 Mazda CX-5 2017 Mazda CX-9 2017 Mazda Mazda3 2017 Mazda Mazda6 2017 Mazda MX-5 2016 Mazda CX-3 2016 Mazda CX-5 2016 Mazda CX-9 2016 Mazda Mazda3 2016 Mazda Mazda6 2016 Mazda MX-5 2015 Mazda CX-5 2015 Mazda Mazda3+ 5 more
Associated Documents
- Download MC-10136772-0001.pdf↗
April 2, 2018•Document ID: 10136778
Service Bulletin/Repair Instructions
POWER TRAIN
Mfr Comm. #:
05-002-18-3454
Date Added:
May 14, 2018
Manufacturer:
MAZDA
Summary
The new SKYACTIV-DRIVE FW6A-EL AT uses "Automatic Transmission Fluid (ATF) Type: FZ". Only use"ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
Associated Products (24)
2018 Mazda CX-3 2018 Mazda CX-5 2018 Mazda CX-9 2018 Mazda Mazda3 2018 Mazda Mazda6 2017 Mazda CX-3 2017 Mazda CX-5 2017 Mazda CX-9 2017 Mazda Mazda3 2017 Mazda Mazda6 2016 Mazda CX-3 2016 Mazda CX-5 2016 Mazda CX-9 2016 Mazda Mazda3 2016 Mazda Mazda6 2015 Mazda CX-5 2015 Mazda Mazda3 2015 Mazda Mazda6 2014 Mazda CX-5 2014 Mazda Mazda3+ 4 more
Associated Documents
- Download MC-10136778-0001.pdf↗
April 2, 2018•Document ID: 10136777
Service Bulletin/Repair Instructions
POWER TRAIN; EQUIPMENT
Mfr Comm. #:
05-001-18-3453
Date Added:
May 14, 2018
Manufacturer:
MAZDA
Summary
Always be sure to use the correct automatic transmission fluid when replacing ATF. Using the wrong ATF may cause shift quality complaints or may even damage the transmission. NOTE: ATF M-V (TYPE M5) IS NOT THE SAME FLUID AS MERCON®V OR MERCON®LV ATF. ATF M-V (TYPE M5) HAS A GREATER VISCOSITY THAN MERCON®V AND MERCON®LV ATF IN LOW TEMPERATURES. ATF M-V (TYPE M5) HAS A GREATER ANTI-JUDDER SPECIFICATION THAN MERCON®V AND MERCON®LV ATF. TRANSMISSION FLUID FLUSHING SHOULD ONLY BE PERFORMED WHEN INSTRUCTED BY THE WORKSHOP MANUAL OR ANY OTHER MAZDA PUBLICATION.
Associated Products (90)
2018 Mazda MX-5 2017 Mazda MX-5 2016 Mazda MX-5 2015 Mazda CX-9 2015 Mazda Mazda5 2015 Mazda MX-5 2014 Mazda CX-9 2014 Mazda Mazda2 2014 Mazda Mazda5 2014 Mazda MX-5 2013 Mazda CX-9 2013 Mazda Mazda2 2013 Mazda Mazda3 2013 Mazda Mazda5 2013 Mazda Mazda6 2013 Mazda MX-5 2012 Mazda CX-7 2012 Mazda CX-9 2012 Mazda Mazda2 2012 Mazda Mazda3+ 70 more
Associated Documents
- Download MC-10136777-0001.pdf↗

← Back to Mazda Mazda6