Mazda CX-5 Service Bulletins (2024)
202 manufacturer communications on file.
- February 11, 2026•Document ID: 11029534OtherENGINE
- Mfr Comm. #:
- PF-26-01
- Date Added:
- March 4, 2026
- Manufacturer:
- MAZDA
SummaryThe coolant control valve updated part is now available and supersedes PYFD-15-16ZA. As a result, PYFD-15-16ZA is no longer available. PW5S-15-16Z is supplied with a dummy plug pre-installed. Critical Installation Requirement: When replacing PW5S-15-16Z, the Powertrain Control Module (PCM) must also be updated to the latest software version. Failure to perform the PCM update may result in drivability concerns or diagnostic trouble codes.
Associated Products (13)Associated Documents - February 6, 2026•Document ID: 11029542Warranty Program/ExtensionENGINE
- Mfr Comm. #:
- SSPD8 Repair c
- Date Added:
- March 4, 2026
- Manufacturer:
- MAZDA
SummarySSPD8 - Check Engine Light ON with DTC P0126:00 - WARRANTY EXTENSION For certain 2018-2025MY CX-5, 2019-2023MY Mazda3, 2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a “Software Update” record for the PCM when using MDARS or IDS. • MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. • IDS – Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealer’s expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.
Associated Products (13)Associated Documents - January 31, 2026•Document ID: 11028102Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 01-003-26
- Date Added:
- February 3, 2026
- Manufacturer:
- MAZDA
SummarySome vehicles may exhibit a check engine light ON with DTC P20F8:00 stored. P20F8:00 - Swirl control circuit range/performance problem. • The DTC is caused by overheating of the Swirl Control Valve (SCV) motor which leads to duty limitation, causing poor openingangle response and resulting in stuck judgment. To eliminate this concern, the PCM control software has been modified.
Associated Products (9)Associated Documents - January 31, 2026•Document ID: 11028092Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 01-001-26a
- Date Added:
- February 3, 2026
- Manufacturer:
- MAZDA
SummarySome customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. • Engine temperature gauge fluctuates. • Low coolant temperature indicator (blue) light stays on longer or turns on while driving. • Poor heater performance, especially at idle. • This concern may be caused if the coolant control valve fail-safe thermostat opens at a temperature lower than the normal temperature due to a deformation of the thermostat diaphragm. To eliminate the concern, the water flow control valve specification has been modified.
Associated Products (13)Associated Documents - January 30, 2026•Document ID: 11028143Warranty Program/ExtensionENGINE
- Mfr Comm. #:
- SSPD8 Repair b
- Date Added:
- February 3, 2026
- Manufacturer:
- MAZDA
SummarySSPD8 - Check Engine Light ON with DTC P0126:00 - WARRANTY EXTENSION For certain 2018-2025MY CX-5, 2019-2023MY Mazda3, 2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a “Software Update” record for the PCM when using MDARS or IDS. • MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. • IDS – Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealer’s expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.
Associated Products (13)Associated Documents - January 30, 2026•Document ID: 11028142Warranty Program/ExtensionENGINE
- Mfr Comm. #:
- SSPD8 Parts and Warr a
- Date Added:
- February 3, 2026
- Manufacturer:
- MAZDA
SummarySSPD8 - Check Engine Light ON with DTC P0126:00 - WARRANTY EXTENSION For certain 2018-2025MY CX-5, 2019-2023MY Mazda3, 2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a “Software Update” record for the PCM when using MDARS or IDS. • MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. • IDS – Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealer’s expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.
Associated Products (15)Associated Documents - January 26, 2026•Document ID: 11028133Service Bulletin/Repair InstructionsUNKNOWN OR OTHER
- Mfr Comm. #:
- SA-005-26
- Date Added:
- February 3, 2026
- Manufacturer:
- MAZDA
SummaryThere are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method • B. Auxiliary Key Code Cut Method 2019 and newer models require a 10-digit key code to accurately cut keys • 5-digit codes CANNOT be provided for 2019 and newer vehicles (the traditional 5-digit code from the key tag or driver's door lock cylinder is not sufficient and will not be issued for key cutting on these models). • Only Mazda-approved key cutting machines can process these 10-digit codes. • Many older key machines do not support 10-digit codes and cannot be updated to do so. In these cases, dealers will need to purchase one of the newer Mazda-approved key cutting machines capable of handling this requirement. • For a list of current Mazda-approved machines and purchasing options, refer to the Mazda Dealer Equipment Program or view the current Mazda approved key machines below.
Associated Products (40)2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-5+ 20 moreAssociated Documents - January 8, 2026•Document ID: 11028091Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 01-001-26
- Date Added:
- February 3, 2026
- Manufacturer:
- MAZDA
SummarySome customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. • Engine temperature gauge fluctuates. • Low coolant temperature indicator (blue) light stays on longer or turns on while driving. • Poor heater performance, especially at idle. • This concern may be caused if the coolant control valve fail-safe thermostat opens at a temperature lower than the normal temperature due to a deformation of the thermostat diaphragm. To eliminate the concern, the water flow control valve specification has been modified.
Associated Products (13)Associated Documents - January 7, 2026•Document ID: 11028095Service Bulletin/Repair InstructionsSEATS
- Mfr Comm. #:
- 09-001-26
- Date Added:
- February 3, 2026
- Manufacturer:
- MAZDA
SummaryThere are wrinkles on the leather seat cushion and/or seat back surface at PDI, when new vehicle is delivered, or when new upholstery is installed under Warranty repair. NOTE: This repair is not a permanent fix, it is meant to make new seats look their best when the vehicle is first presented to the customer. Wrinkles may not be completely removed after the repair is completed. Leather is a natural material and may develop some wrinkles due to aging and wear during normal usage.
Associated Products (33)2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-5+ 13 moreAssociated Documents - January 6, 2026•Document ID: 11028128Service Bulletin/Repair InstructionsWHEELS
- Mfr Comm. #:
- SA-002-26
- Date Added:
- February 3, 2026
- Manufacturer:
- MAZDA
SummarySome customers may complain that the tire sidewalls are distorted or "damaged". Sidewall waviness/indentations/undulations are common on radial tires and are more noticeable on tires with taller sidewalls. The higher the tire pressure, the more noticeable the effect will be. Be sure to set the tire pressures at the recommended tire pressure on the vehicle tire label. Sidewall indentations are a cosmetic condition that does not affect the performance of the tires.
Associated Products (15)Associated Documents - January 5, 2026•Document ID: 11028127Service Bulletin/Repair InstructionsUNKNOWN OR OTHER
- Mfr Comm. #:
- SA-001-26
- Date Added:
- February 3, 2026
- Manufacturer:
- MAZDA
SummarySome customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet.
Associated Products (40)2026 Mazda CX-302026 Mazda CX-52026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-5+ 20 moreAssociated Documents - December 24, 2025•Document ID: 11026902Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 01-003-25b
- Date Added:
- January 3, 2026
- Manufacturer:
- MAZDA
SummarySome customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. • Engine temperature gauge fluctuates. • Low coolant temperature indicator (blue) light stays on longer or turns on while driving. • Poor heater performance, especially at idle. • This concern may be caused if the coolant control valve fail-safe thermostat opens at a temperature lower than the normal temperature due to a deformation of the thermostat diaphragm. To eliminate the concern, the water flow control valve specification has been modified.
Associated Products (13)Associated Documents - December 23, 2025•Document ID: 11027028Warranty Program/ExtensionENGINE
- Mfr Comm. #:
- SSPD8a Repair
- Date Added:
- January 6, 2026
- Manufacturer:
- MAZDA
SummarySSPD8 - Check Engine Light ON with DTC P0126:00 - WARRANTY EXTENSION For certain 2018-2025MY CX-5, 2019-2023MY Mazda3, 2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a “Software Update” record for the PCM when using MDARS or IDS. • MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. • IDS – Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealer’s expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.
Associated Products (13)Associated Documents - December 17, 2025•Document ID: 11026917Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SA-061-25
- Date Added:
- January 4, 2026
- Manufacturer:
- MAZDA
SummaryIf you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
Associated Products (40)2026 Mazda CX-302026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-52023 Mazda CX-30+ 20 moreAssociated Documents - December 17, 2025•Document ID: 11026908Service Bulletin/Repair InstructionsUNKNOWN OR OTHER; ELECTRICAL SYSTEM
- Mfr Comm. #:
- SA-017-25d
- Date Added:
- January 3, 2026
- Manufacturer:
- MAZDA
SummaryMazda Connect Services - Frequently Asked Questions (FAQ)
Associated Products (34)2026 Mazda CX-302026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-52023 Mazda CX-30+ 14 moreAssociated Documents - December 16, 2025•Document ID: 11026916Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EXTERIOR LIGHTING; ENGINE
- Mfr Comm. #:
- SA-023-25c
- Date Added:
- January 4, 2026
- Manufacturer:
- MAZDA
SummarySome customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop • Door Lock / Unlock • Lights ON / OFF • Climate Control • 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ". Page
Associated Products (34)2026 Mazda CX-302026 Mazda CX-502026 Mazda CX-702026 Mazda CX-902026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda CX-502025 Mazda CX-702025 Mazda CX-902025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda CX-502024 Mazda CX-902024 Mazda Mazda32024 Mazda MX-52023 Mazda CX-30+ 14 moreAssociated Documents - December 10, 2025•Document ID: 11026904Service Bulletin/Repair InstructionsUNKNOWN OR OTHER
- Mfr Comm. #:
- 07-004-25a
- Date Added:
- January 3, 2026
- Manufacturer:
- MAZDA
SummaryA musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. “Mazda Air Cooling Coil Coating” is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers.
Associated Products (28)2026 Mazda CX-302026 Mazda Mazda32026 Mazda MX-52025 Mazda CX-302025 Mazda CX-52025 Mazda Mazda32025 Mazda MX-52024 Mazda CX-302024 Mazda CX-52024 Mazda Mazda32024 Mazda MX-52023 Mazda CX-302023 Mazda CX-52023 Mazda CX-92023 Mazda Mazda32023 Mazda MX-52022 Mazda CX-302022 Mazda CX-52022 Mazda CX-92022 Mazda Mazda3+ 8 moreAssociated Documents - December 5, 2025•Document ID: 11027024Warranty Program/ExtensionENGINE
- Mfr Comm. #:
- SSPD8 Parts and Warr
- Date Added:
- January 6, 2026
- Manufacturer:
- MAZDA
SummarySSPD8 - Check Engine Light ON with DTC P0126:00 - WARRANTY EXTENSION For certain 2018-2025MY CX-5, 2019-2023MY Mazda3, 2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a “Software Update” record for the PCM when using MDARS or IDS. • MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. • IDS – Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealer’s expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.
Associated Products (13)Associated Documents - December 5, 2025•Document ID: 11027023Warranty Program/ExtensionENGINE
- Mfr Comm. #:
- SSPD8 Dlr Ltr
- Date Added:
- January 6, 2026
- Manufacturer:
- MAZDA
SummarySSPD8 - Check Engine Light ON with DTC P0126:00 - WARRANTY EXTENSION For certain 2018-2025MY CX-5, 2019-2023MY Mazda3, 2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a “Software Update” record for the PCM when using MDARS or IDS. • MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. • IDS – Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealer’s expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.
Associated Products (13)Associated Documents - December 4, 2025•Document ID: 11026901Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 01-003-25a
- Date Added:
- January 3, 2026
- Manufacturer:
- MAZDA
SummarySome customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. This concern may be caused if the coolant control valve fail-safe thermostat opens at a temperature lower than the normal temperature due to a deformation of the thermostat diaphragm. To eliminate the concern, the water flow control valve specification has been modified.
Associated Products (13)Associated Documents