Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2023-2024 Toyota Venza, 2023-2025 RAV4 Prime, RAV4, Highlander, GR Corolla, Crown, 2024-2025 Lexus TX, LS, Toyota Tacoma, Grand Highlander, and 2025 Lexus RX, Toyota Crown Signia, Camry, RAV 4 Plug-in Hybrid (PHEV), and 4 Runner vehicles. Due to an error in the instrument panel software at vehicle startup, the instrument panel may fail to display vehicle speed, brake system, and tire pressure warning lights.
Toyota Engineering & Manufacturing (Toyota) is recalling certain 2022 Lexus LX 600, Lexus NX 350h, Lexus NX 450h+, Toytoa RAV4 Hybrid, 2021-2022 Lexus LS 500h, Toyota Mirai, RAV4 PRIME, Sienna, Venza, and 2020-2022 Toyota Highlander Hybrid vehicles. The Skid Control ECU software may not turn on the Vehicle Stability Control (VSC) system when the vehicle is restarted after the driver has disabled the VSC system. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 126, "Electronic Stability Control Systems."
The contact owns a 2024 Toyota Venza. The contact stated that upon parking the vehicle, the vehicle unintendedly accelerated to 15 MPH, and the contact continued to depress the brake pedal. The vehicle came to a complete stop after crashing into the base of a light pole and a retaining wall. The front passenger’s side of the vehicle was damaged. The air bags failed to deploy. The contact was not injured. The vehicle was not towed. The message "BRAKES" was displayed. A Police report was not filed. The local dealer was contacted; however, the vehicle was not diagnosed. The VIN was not included in a recall. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 14,500.
Rear passenger side window exploded (shattered) while driving on the Hardy Toll Road in [XXX]. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
No injuries · No fire · No crash
The center console has cracked and has sharp corners causing an increased risk of injury. Also may cause one to jerk the wheel if placing their elbow down and not expecting the sharp corner. No accident occurred as of yet, but could if someone else were to be driving my car and place their arm down on the center console. I have to place my arm down a certain way to avoid getting poked. Just wanted to report this as I am not sure if other owners have reported similar issue with their center console developing sharp edges. Would probably be similar to NHTSA campaign number 26V368000
No injuries · No fire · No crash
What component or system failed or malfunctioned, and is it available for inspection upon request? I purchased four tires from Belle Tires on April 1, 2026, 14 days ago (note: mileage at accident 10,776 vs mileage at tire purchase 10,360 or 416 miles of wear). On Wednesday, April 15th, I was about to change lanes after entering the Tri-State Expressway (route 294) going southbound from Half-Day Rd. (route 22), I had crossed the first two lanes without incident, and moving into the third lane, when I experienced a blowout of my driver’s-side rear tire. The car started a fishtail counter-clockwise spin and crossed the third and the fourth lanes (i.e., the far left lanes) before smashing into the concrete median, separating my Southbound lanes from the opposing traffic lanes. I have kept both the tire and rim in my garage. How was your safety or the safety of others put at risk? As I started sliding or spinning, I cannot honestly say, whether or not I hit the brakes or can really describe the spinning that occurred. As the rim of blowout tire was evenly torn up on its outer edge, I know that the tire was turning. All I can recall is hearing the car hit the concrete median twice. I know that it had to be counterclockwise since I started going southbound, and after the car came to a rest next to the median, I was facing southbound again. Has the problem been reproduced or confirmed by a dealer or independent service center? I took the tire on it’s rim to the Belle dealer who would not acknowledge a blowout, but he kept insisting that he is not an expert on crash interpretations. Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? Allstate Insurance, Toyota used a Bosch representative to retrieve the Electronic Data Recording (EDR) information. I have copy of this report available for expert interpretation. No warnings were given prior to this blowout.
Vehicle has an open safety recall (25TD01) for rear traction motor cable corrosion. Corwin Toyota in Boulder, CO was notified in January and failed to order the part. Came in April 14 for the scheduled repair and was told the part was never ordered. It is now May 24 and the recall has still not been completed despite multiple follow-up attempts. Dealership has provided no explanation for the April failure and no confirmed repair date.
No injuries · No fire · No crash