Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2022-2026 Toyota, Lexus, and Subaru Solterra vehicles equipped with a Panoramic View Monitor (PVM) system. Please see the recall report for a complete list of models. A software error may cause the rearview camera to freeze or display a blank screen when the vehicle is in reverse. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rear Visibility."
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2023-2025 bZ4X, Lexus RZ, and Subaru Solterra vehicles. During certain HVAC system faults, such as electrical compressor failure, the defroster and defogger system may become inoperative.
Gulf States Toyota, Inc. (GST) is recalling certain Toyota 2023 GR Supra, 2024 4 Runner, Corolla, Grand Highlander, Grand Highlander Hybrid, Land Cruiser Hybrid, Tacoma, Tacoma Hybrid, 2023-2024 BZ4X, Corolla Cross Hybrid, GR Corolla, GR86, Highlander, Highlander Hybrid, Prius, Prius Prime, Sequoia Hybrid, Tundra, Tundra Hybrid, Venza Hybrid, 2023-2025 Crown, and 2025 Camry Hybrid vehicles equipped with GST accessories. The load carrying capacity modification label may display inaccurate added weight values. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 110, "Tire Selection and Rims."
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2023 Subaru Solterra and Toyota BZ4X vehicles. The hub bolts on the wheels may loosen, causing a wheel to detach from the vehicle after low-mileage use.
I was driving during heavy rain when I heard and felt a big thump. I wasn't sure what happened as I did not hit anything in the road. I was in my neighborhood driving at low speeds (<30mph). When I got home, I realized my fender liners and lower splash guard of my car were missing. I went back out to retrieve these pieces of my car, and it appeared the fender liners and the splash guard got torn off my car without impact with anything, as nothing was in the road near it. I was going to attempt to reconnect them but the plastic clips on the front bumper also ripped off, making this a very expensive repair requiring bumper replacement and sensor recalibration. This obviously could put others at risk of running over a large number of components that were left in the road. I read many other instances of other people with the same vehicle (as well as with the Solterra) having an issue where the felt fender liners can become saturated with water, sag, and get caught in the wheels, ripping them off. I was one of those unlucky people to lose both sides and the splash guard all at the same time. The dealership / body shop inspected the vehicle. No warnings at all - just sudden ingestion of the fender liners into my drivetrain.
No injuries · No fire · No crash
While operating my 2024 Toyota bZ4X at very low speed on the road , I observed a stationary shipping container directly ahead and applied the brake pedal with maximum force approximately 4 seconds before contact. I held the brake pedal at full pressure continuously. I never touched the accelerator. The vehicle came to what appeared to be a complete stop then continued to advance and made physical contact with the container despite my maintained maximum brake input. The vehicle's own ECU-recorded Freeze Frame Data (retrieved by an authorized Toyota dealer using PCS Data Viewer) confirms the following at the time of the event: Driver brake pedal torque was at sensor saturation (4,048 Nm — the maximum value the sensor can record) for approximately 1.75 seconds prior to impact. Brake hydraulic line pressure peaked at 12.144 MPa and remained above 7.8 MPa throughout that period. Throttle position was 0.0% for the entire recorded interval. All four wheel-speed sensors recorded 0.00 km/h for approximately 2.95 seconds prior to impact. Steering input was effectively neutral; no skid or loss of directional control occurred. The longitudinal accelerometer recorded a peak deceleration spike of -8.97 m/s² at the moment of impact — a value that requires forward velocity and is physically inconsistent with the wheel-speed data showing the vehicle stopped. The Pre-Collision System (PCS) main switch was ON throughout, with no faults, no obstruction flags, and no warning, pre-brake, brake-assist, or auto-brake activation recorded. The Parking Support Brake (PKSB) did not activate. No diagnostic trouble codes were set. In plain terms: with maximum brake pressure applied and zero throttle input, my vehicle continued to move forward into a clearly visible stationary obstacle. The brakes did not maintain authority over the powertrain's creep torque, and no advanced safety system intervened. This indicates a potential defect in the vehicle's brake-override / creep-suppression
The vehicle experienced a sudden, catastrophic brake-by-wire system failure while operating in one-pedal driving (Regeneration Boost mode). While decelerating at a low speed behind an 18-wheeler semi-truck, the vehicle failed to continue slowing down. I immediately depressed the physical brake pedal, but the vehicle completely ignored the foot pressure. The pedal and braking system became completely unresponsive, and the vehicle kept rolling forward uncommanded. Despite keeping the brake pedal fully depressed, the vehicle did not decelerate, resulting in a front-end low-speed collision with the metal rear bumper of the semi-truck. Because the collision occurred at a very low speed, the operator of the commercial truck was unaware of the impact and safely continued driving forward without stopping. The vehicle's brakes entirely refused to re-engage until I frantically pumped the physical brake pedal and cycled/pressed vehicle control power switches. This action seemingly forced the electronic braking modules to reboot or re-establish hydraulic pressure, allowing the vehicle to finally come to a stop. The vehicle was subsequently removed from the active roadway. This is a severe, life-threatening safety defect involving a total loss of electronic brake-by-wire and friction braking application without any mechanical override intervention, presenting an extreme hazard. The vehicle has been towed directly to an authorized Toyota dealership for a comprehensive electronic diagnostic pre-scan of the Skid Control ECU, Electronic Parking Brake system, and 12-volt auxiliary power systems to retrieve the stored DTC fault logs and freeze-frame data.
The car show on the screen a message in regards to the Adaptative Cruise Control Malfunction and it’s showing an orange sign light.. Another problem it’s in regards the AC.. it’s not working
No injuries · No fire · No crash
The contact owns a 2024 Toyota BZ4X. When pressing the accelerator toelerator pedal to go onto the freeway, the vehicle failed to accelerate and suddenly shifted to neutral. The contact would have to press the brake pedal, the contact would immediately shift the vehicle back to Drive and continue forward. While continuing to drive, the vehicle accelerated. There were no warning lights. The failure had occurred 3 times. When attempting to start the vehicle one day, the vehicle failed to start. The tow company came and provided a jump-start, and then advised the contact to drive carefully, but if it failed to go in reverse. The next morning, the tow company's mechanic came again and confirmed battery failure, then recommended the vehicle be taken to the dealer. The vehicle was towed to the dealer, who stated that the battery had not failed, but had not provided a diagnosis for the failure. The vehicle had not been repaired. The dealer had driven the vehicle back to the contact's home. After the vehicle was returned, the failure occurred again. The manufacturer was informed, and a claim had been filed. The failure mileage was 9,787.
No injuries · No fire · No crash