Mitsubishi Lancer Evolution Complaints

229 consumer complaints on file.

#10299578January 13, 2010
ENGINE AND ENGINE COOLING:ENGINE
IN AUGUST I NOTICED A WEIRD NOISE COMING FROM THE TIMING BELT AREA OF MY CAR. THE CAR WAS PERFECTLY FINE AND DRIVEN NORMALLY. I STARTED THE CAR AND THE NOISE APPEARED OUT OF NOWHERE. THE NOISE SOUNDS LIKE A WASHING MACHINE AND IS ONLY PRESENT WHEN THE CAR IS STARTED UP AND IS COLD. AFTER APPROXIMATELY 15 MINUTES OF DRIVING, THE NOISE DISAPPEARS. I AM WORRIED THAT THERE IS SOMETHING TERRIBLY WRONG IN THAT AREA. I DO NOT WANT MY ENGINE TO BREAK. *TR
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#10299566January 12, 2010
ENGINE AND ENGINE COOLING:ENGINE
LOUD NOISE COMING FROM THE TIMING BELT AREA. SOUNDS LIKE A FAULTY PULLEY OR THE BELT RUBBING ON SOMETHING. TOOK IT INTO THE DEALER AND THEY REPLACED THE TIMING BELT IDLER PULLEY. BEFORE I LEFT THE DEALERSHIP I TOLD THEM I STILL HEAR THE SAME SOUND JUST QUIETER. THEY TOLD ME IF IT GETS LOUDER TO COME BACK. THAT WAS ABOUT A MONTH AGO AND IT HAS GOTTEN LOUDER SINCE. MY CONCERN IS CATASTROPHIC ENGINE FAILURE. NOBODY HAS BEEN ABLE TO PROPERLY DIAGNOSE THE ISSUE. THIS COULD CAUSE A SERIOUS ACCIDENT IF SEVERE ENGINE FAILURE OCCURRED AT SPEED. *TR
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#10298968January 11, 2010
ENGINE AND ENGINE COOLING:ENGINE
A COUPLE MONTHS AGO, I NOTICED A SQUEAKING SOUND COMING FROM THE PASSENGER SIDE OF MY ENGINE WHEN MY CAR WAS IDLING. AFTER THE CAR WARMED UP (5-10 MIN), THE SOUND WOULD GO AWAY. THE SOUND APPEARED TO BE BELT RELATED SO I CHECKED THE SERPENTINE (ACCESSORY) BELT AND NOTICED SIGNS OF WEAR AND TEAR ON THE BELT AND THE IDLER PULLEY . I CHANGED THE BELT OUT (WAS CLOSE TO RECOMMENDED REPLACEMENT DATE ANYWAY) BUT THE SOUND IS STILL THERE. I SEARCHED THE INTERNET AND FOUND THAT THIS PROBLEM IS QUITE COMMON WITH 2006 EVOLUTION OWNERS AND THERE IS NO DEFINITE FIX FROM THE DEALER. THIS NEEDS TO BE ADDRESSED BY THE MANUFACTURER BECAUSE THE WEAR AND TEAR CREATED BY THE BELT/PULLEY (OR WHATEVER THE CULPRIT MAY BE) COULD EASILY LEAD TO A FAILURE IN ONE OF THE ACCESSORY SYSTEMS (ALTERNATOR, WATER PUMP, POWER STEERING) AND COULD BE DANGEROUS TO MY CAR OR EVEN WORSE TO ME. *TR
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#10293521November 25, 2009
ENGINE AND ENGINE COOLING:ENGINE
BAD BEARING NOISE COMING FROM TIMING BELT AREA. THIS IS A PROBLEM WITH THE TIMING BELT IDLER PULLEY. I HAVE HAD IT REPLACED BY THE DEALER AND THE EXACT SAME NOISE CAME BACK WITHIN 10K MILES. THIS NOISE APPEARED WITH 31K MILES ON THE CAR. *TR
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#10292243November 15, 2009
ENGINE AND ENGINE COOLING
A STRANGE "RUBBING, GRINDING" NOISE COMING FROM THE TIMING BELT AREA. *TR
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#10291462November 9, 2009
ENGINE AND ENGINE COOLING
CAR NEEDS TO BE SITTING AT AN IDLE SPEED, AND FIRST STARTED BECOMING AUDIBLE A FEW MONTHS AGO, BUT WAS INTERMITTENT. I TOOK THE CAR INTO THE DEALER AND THEY DID NOT HAVE A FIX AND BLAMED IT ON THE VALVES NEEDING ADJUSTMENT AND MY SERPENTINE BELT. THE VALVES ON THIS PARTICULAR CAR ARE HYDRAULIC AND DO NOT NEED SERVICING AND WHEN I REMOVED MY OWN SERPENTINE BELT, THE NOISE WAS STILL AUDIBLE! IT IS DEFINITELY COMING FROM THE TIMING BELT AREA AND SOUNDS LIKE IT IS ALMOST HITTING OR SCRAPING SOMETHING! ITS A SERIOUS CONCERN AS I DON'T NEED A TIMING BELT FAILURE WHILE DRIVING OUT ON THE ROAD, DUE TO A MANUFACTURERS DEFECT IN ONE/SOME OF THE TIMING BELT COMPONENTS!! THE SCRAPING NOISE AT IDLE IS ALMOST DAILY WHEN HOT OR COLD, IT DOESN'T MATTER ANYMORE. I'VE ALSO TAKEN IT TO ANOTHER DEALER RECENTLY AND THEY SAID THEY WERE AWARE OF THE ISSUE, BUT THERE IS NO FIX AND ITS QUITE COMMON FOR MY VEHICLE! *TR
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#10291401November 8, 2009
ENGINE AND ENGINE COOLING:ENGINE
I FIRST NOTICED THAT MY 2006 MITSUBISHI LANCER EVOLUTION RS STARTED TO MAKE A GRINDING/SCRAPPING NOISE THAT SEEMED TO BE GENERATING FROM THE TIMING BELT AREA WHEN MY CAR HAD APPROXIMATELY 35,000 MILES ON THE ODOMETER. IT SEEMED TO BE A NOISE THAT WAS PRESENT AT IDLE AND UPON COLD START UPS AND NOW OCCASIONALLY I HEAR IT EVEN WHEN THE CAR IS FULLY WARMED UP. I STARTED TO RESEARCH THIS ON VARIOUS FORUMS AND INTERNET, ONLY TO FIND THAT IT WAS A COMMON PROBLEM WITH A CLEAR SOLUTION. THERE HAVE BEEN A FEW DEALERSHIPS WHO HAVE SEEMED TO HAVE RESOLVED THIS ISSUE BUT EACH FIX SEEMED TO VARY WITHIN THE TIMING BELT AREA. THE TIMING BELT, SENSOR BLADE, TENSIONER, TENSIONER PULLEYS, ETC. HAVE BEEN KNOWN TO CAUSE THIS ISSUE. THIS CAR IS MY DAILY DRIVER AND ABOUT 90% OF THE TIMES MY KIDS ARE IN THIS CAR WITH ME. IT WOULD BE TERRIBLE IF MY ENGINE BREAKS DOWN ON ME WHILE DRIVING AROUND WITH MY KIDS IN THE CAR. THIS CAN BE A DANGEROUS PROBLEM. I URGE MITSUBISHI TO STRONGLY CONSIDER A RECALL FOR THIS. WITH SUCH AN AMAZING CAR I WOULD HOPE MITSUBISHI WOULD STANDBY IT AND DO THE RIGHT THING!*TR
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#10291199November 6, 2009
ENGINE AND ENGINE COOLING:ENGINE
I 1ST STARTED HEARING A METAL SCRAPING NOISE COMING FROM THE DRIVE BELT AREA AROUND 20,000 MILES ON THE ODOMETER OF MY 2006 MITSUBISHI LANCER EVOLUTION IX MR. AFTER RESEARCHING THIS ONLINE, I FOUND THIS TO BE A COMMON/FREQUENT PROBLEM REPORTED BY MANY OTHER OWNERS OF THE SAME CAR THROUGHOUT THE WEB. IN FACT, I EVEN FOUND A YOUTUBE CLIP OF THE EXACT SAME NOISE CREATED FOR THE EXACT SAME ISSUE. THE NOISE HAS BEEN DETERMINED TO BE INVOLVING THE TIMING BELT RUBBING AGAINST THE CRANKSHAFT BLADE. I'VE ONLY FOUND IT TO ONLY BE AUDIBLE AT IDLE, SO IT MAKES SENSE THAT IT'S SOME SORT OF TIMING BELT TENSION ISSUE. SOME DEALERSHIPS ARE RESOLVING THIS ISSUE BY REPLACING THE TIMING BELT, CRANKSHAFT BLADE, TIMING BELT TENSIONER, AND SOMETIMES EVEN THE IDLER PULLEY. MY LOCAL DEALERSHIP DENIED MY WARRANTY REPAIR CLAIM TO GET THE METAL SCRAPING NOISE ISSUE FIXED, AND CHARGED ME $140 TO SPRAY ENGINE DEGREASER ON UNDRESSED ACCESSORY BELTS, CLAIMING THAT THE ACCESSORY BELTS WERE OVERDRESSED AND THAT IS WHAT CAUSED THE NOISE. UNFORTUNATELY, MY CAR IS STILL MAKING THE SAME NOISE, WHICH I AM CERTAIN IS BEING CAUSED BY THE SAME TIMING BELT/CRANKSHAFT BLADE ISSUE. MY ONLY CONCERN IS THAT THE TIMING BELT WILL AT SOME POINT IN THE FUTURE FAIL DUE TO THE OBVIOUS RUBBING/CONTACT THAT IS OCCURRING WITH THE CRANKSHAFT BLADE, SO I WOULD LIKE TO GET THIS FIXED BEFORE THAT HAPPENS. GLENDALE MITSUBISHI IN GLENDALE, CA IS AWARE OF THE PROBLEM, AND ACKNOWLEDGED THAT IT'S A COMMON ISSUE, BUT WAS NOT WILLING TO DISCUSS IT WITH MY LOCAL DEALERSHIP, STATING THAT MY LOCAL DEALERSHIP SHOULD CONTACT THE MITSUBISHI TECH LINE INSTEAD. I BELIEVE THIS TO BE A VERY COMMON PROBLEM WITH THE 2006 LANCER EVOLUTIONS, AND FIRMLY BELIEVE THAT MITSUBISHI SHOULD BE RESPONSIBLE FOR ISSUING A SERVICE BULLETIN TO GET THIS RESOLVED. *TR
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#10291287November 6, 2009
ENGINE AND ENGINE COOLING:ENGINE
I FIRST NOTICED THAT MY 2006 MITSUBISHI LANCER EVOLUTION RS STARTED TO MAKE A GRINDING/SCRAPPING NOISE THAT SEEMED TO BE GENERATING FROM THE TIMING BELT AREA. THE CAR HAD APPROXIMATELY 18,000 MILES ON THE ODOMETER. IT SEEMED TO BE A NOISE THAT WAS PRESENT AT IDLE AND UPON COLD START UPS. I STARTED TO RESEARCH THIS ON VARIOUS FORUMS AND INTERNET, ONLY TO FIND THAT IT WAS A COMMON PROBLEM WITH A CLEAR SOLUTION. THERE HAVE BEEN A FEW DEALERSHIPS WHO HAVE SEEMED TO HAVE RESOLVED THIS ISSUE BUT EACH FIX SEEMED TO VARY WITHIN THE TIMING BELT AREA. THE TIMING BELT, SENSOR BLADE, TENSIONER, TENSIONER PULLEYS, ETC. HAVE BEEN KNOWN TO CAUSE THIS ISSUE. I DROVE MY CAR 3.5 HRS TO AN OUTSTANDING MITSUBISHI DEALERSHIP WHICH COULD NOT DIAGNOSIS MY PROBLEM. IT APPEARS THAT THE DRIVE MADE WHATEVER IT WAS GO AWAY FOR THE MOMENT. THIS SCARES ME! THIS CAR IS MY DAILY DRIVER AND ABOUT 90% OF THE TIMES MY KIDS ARE IN THIS CAR WITH ME. IT WOULD BE TERRIBLE IF MY ENGINE BREAKS DOWN ON ME WHILE DRIVING AROUND WITH MY KIDS IN THE CAR. THIS CAN BE A DANGEROUS PROBLEM. I URGE MITSUBISHI TO STRONGLY CONSIDER A RECALL FOR THIS. WITH SUCH AN AMAZING CAR I WOULD HOPE MITSUBISHI WOULD STANDBY IT AND DO THE RIGHT THING! *TR
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#10291153November 5, 2009
UNKNOWN OR OTHER
1. DRIVING 2. IRRITATING TICKING FROM PASSENGER SIDE OF ENGINE BAY. SEEMS TO CAUSE WEAR AND TEAR ON BELTS ON ENGINE. SO FAR NO CONSEQUENCES AS BELT HASN'T BROKEN. 3. NO PART HAVE BEEN REPLACED AS OF YET. 4. IN SHORT IT SEEMS ALMOST ALL EVO IX'S ARE AFFECTED BY THIS BELT WEAR ON THE IDLER PULLEY, POWER STEERING PULLEY, AND POSSIBLY OTHERS. I JUST DON'T WANT TO SEE ONE OF THESE BELTS BREAK ON THIS PERFORMANCE TURBO CAR AT HIGH SPEEDS... COULD CAUSE MANY INJURIES IN MY OPINION. KEEP AND EYE OUT FOR MANY MANY OTHERS TO SEND IN A REPORT IN THE NEXT FEW DAYS ON THE EVO IX'S AS I WILL BE POSTING UP A LINK TO THIS SITE ON OUR MAIN COMMUNITY SITE. *TR
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#10287130October 12, 2009
ELECTRONIC STABILITY CONTROL (ESC), POWER TRAIN
MITSUBISHI MOTORS OF AMERICA HAS A AWD ECU SOFTWARE UPDATE FOR VEHICLES SPECIFICALLY DRIVEN IN COLD CONDITIONS. DEALERSHIPS AND MITSUBISHI CORPORATE HAVE DENIED MY CLAIM TO OBTAIN THIS SOFTWARE BECAUSE MY CAR WAS SOLD IN CALIFORNIA AND THEY HAVE SAID IT IS NOT ELIGIBLE. I TAKE MY VEHICLE EVERY YEAR UP IN THE SIERRA NEVADA MOUNTAIN RANGE WHERE TEMPERATURE CONDITIONS ARE SIMILAR TO ANY OF THE NORTHERN STATES WITHIN THE SERVICE BULLETIN. THE MITSUBISHI SERVICE BULLETIN NUMBER IS SC-09-002 ALSO AVAILABLE HERE ON GOOGLE DOCS TO READ ( HTTP://DOCS.GOOGLE.COM/FILEVIEW?ID=0BZNIGP9LGBK8NTU5OTRINJGTZTJHMC00MJY0LWI2NMMTOWZHZJU1NZFKNDCZ&HL=EN) IT STATES THAT "THIS REPROGRAMMING PROCEDURE WILL MODIFY THE ALL-WHEEL-CONTROL (AWC) ECU SOFTWARE TO ACCURATELY MATCH THE OPERATIONS CHECK OF THE AYC/ACD MOTOR WITH CURRENT AMBIENT CONDITIONS. EXTREMELY COLD WEATHER CAUSES INCREASED EXCESSIVE LOAD ON THE MOTOR, WHICH COULD RESULT IN DAMAGE TO THE MOTOR. THIS BULLETIN DESCRIBES PROCEDURES TO REPROGRAM THE AWC ECU WITH NEW SOFTWARE PARAMETERS TO PREVENT THIS CONDITION." THE SAFETY CONCERN IS THAT IF I'M USING MY AWD VEHICLE IN COLD CONDITIONS AND THE CRITICAL AWD COMPONENTS FAIL DUE TO DRIVING IN COLD CONDITIONS AS STATED IN THE SERVICE BULLETIN AND CAUSE ME TO HAVE AN ACCIDENT OR EVEN HURTING OTHERS WHICH CAN BE PREVENTED WITH A 20 MINUTE SOFTWARE UPDATE THAT IS AVAILABLE NOW. *TR
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#10286586October 6, 2009
STRUCTURE:BODY, SEATS
PURCHASE MY 2008 MITSUBUSHI EVOLUTION X ABOUT ONE MONTH AGO WITH 2,900MILES. I DON'T DRIVE IT OFTEN SINCE I HAVE A COMPANY CAR. MY CURRENT MILES IS 4,400MILES. I AM BEGINNING TO NOTICE ALOT OF SMALL CHIPS TOWARD THE BACK DOORS BOTTOM CORNER NEAR QUARTER PANEL ON BOTH SIDE OF THE VEHICLE. BEEN ON MANY FORUMS AND ALOT OF EVO X OWNER ARE EXPERIENCING THE SAME PAINT PROBLEM.THE ROAD CONDITION HERE ARE IN GOOD SHAPE, SO I DON'T SEE WHY THE PAINT IS CHIPPING AWAY. IM AFRAID WHEN I REACH 10,000MILES, THE CAR INTERIOR WOULD STILL BE FAIRLY NEW BUT THE EXTERIOR WOULD HAVE PAINT CHIPPED EVERYWHERE. ANOTHER ISSUE ARE THE RECARO SEAT FABRIC ARE COMING OUT NEAR THE HEAD REST PART. THE FABRIC ARE CONING OUT RIGHT WHERE THE FABRIC TUCK UNDER INTO THE CARBON FIBER LOOKING PLASTIC PIECE NEAR THE HEADREST. YOU ARE ABLE TO SEE THE STAPLES THAT ARE COMING OUT. THIS IS HAPPENING TO BOTH SEATS, DRIVER AND PASSENGER. I HAVE READ SEVERAL FORUMS BUT OWNERS WHO HAVE SPOKE TO MITSUBISHI ABOUT THE PAINT ISSUE WERE TURN DOWN.THOSE OWNER SAID MITSUBISHI ARE NOT WILLING TO DO ANYTHING ABOUT THIS ISSUE. *TR
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#10285978October 1, 2009
SERVICE BRAKES, HYDRAULIC
BRAKE FINISH IS INFERIOR AND PEELING. *TR
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#10284178September 16, 2009
SERVICE BRAKES, HYDRAULIC
BRAKE ISSUE. *TR
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#10261125March 9, 2009
ELECTRICAL SYSTEM
THERE IS A PROBLEM WITH MITSUBISHI LANCER EVOLUTIONS MADE FROM 2003-2006. I HAVE HAD 2 OF THESE CARS AND SAME PROBLEM... ALMOST STARTED A FIRE IN MY CAR.. . WHERE THE MAIN WIRING HARNESS GOES THROUGH THE DRIVERS SIDE FRONT FENDER, THERE'S A RUBBER GROMMET THAT IS SUPPOSED TO BLOCK WATER. WELL IN MY 2 CARS AND ABOUT 100 OTHERS ON THE AUTO FORUM I FREQUENT,(WWW.EVOLUTIONM.NET) THE RUBBER GROMMET FAILS TO DO ITS JOB OF BLOCKING WEATHER AND WATER IS LEAKING THROUGH GOING DOWN THE MAIN WIRING HARNESS AND INTO THE WIRING CONNECTORS. FROM THERE THE AVERAGE OWNER LIKE ME IS GETTING THERE HORN, LIGHTS WIPERS SRS LIGHT ETC. TURNING ON/OFF RAPIDLY WHILE DRIVING. SOME HAVE EXPERIENCED THE CAR SUDDENLY SHUTTING OFF WHILE DRIVING, WELL ALONG WITH THAT YOU LOOSE POWER STEERING AND BRAKES. PLEASE DO WHAT EVER NEEDS TO BE DONE TO MAKE THIS A RECALL. AS IT I AM SURE HAS AND WILL CAUSE MANY TRAFFIC ACCIDENTS. PLEASE KEEP OUR ROADS SAFE. *TR
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#10251551December 12, 2008
POWER TRAIN
2003 MITSUBISHI LANCER EVOLUTION. LOUD GRINDING NOISES COMING FROM THE TRANSMISSION WITHIN A FEW THOUSAND MILES. CARS UNDER 8 THOUSAND MILES HAVING TO REPLACE CLUTCHES AND TRANSMISSIONS. GEARS POPPING INTO NEUTRAL. DEALERSHIP ACCEPTED WARRANTY AND IS CURRENTLY WORKING ON THE CAR. CAR WAS RETURNED A 2ND TIME TO BE LOOKED AT AGAIN. *TR
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#10243393September 25, 2008
EXTERIOR LIGHTING, INTERIOR LIGHTING
THE CAR WAS RUNNING FINE AND HAD NO PROBLEMS THEN WHEN I STARTED IT UP ONE DAY THE DASH LIGHTS AND TAIL LIGHTS STARTED PULSING. I THOUGHT IT MIGHT BE THE ALTERNATOR SO I HAD IT CHECKED OUT. THE SHOP SAID THE ALTERNATOR IS IN PERFECT CONDITION AND COULDN'T FIGURE OUT THE PROBLEM. THE PULSATING LIGHTS IS STILL GOING ON, AND I HAVEN'T BEEN ABLE TO FIND OUT WHAT THE PROBLEM IS. *TR
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#10237677August 11, 2008
POWER TRAIN:MANUAL TRANSMISSION
THE 5TH GEAR SYNCRO HAS FAILED ON THE CAR AT 60,000 MILES. THIS IS A KNOWN DEFECT TO MITSUBISHI AND THEY HAVE DEVELOPED NEW, STRONGER PARTS AS PART OF A TSB. HOWEVER, MITSUBISHI IS REFUSING TO REPAIR THE DEFECT CITING "ABUSE". *TR
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#10231547June 19, 2008
ENGINE AND ENGINE COOLING
MY CAR WAS PURCHASED ON 11/23/05. ONE WEEK AFTER PURCHASE, SERVICE MANAGER INFORMED ME THAT MY OIL WAS REALLY LOW AND ADDED A QUART OF OIL. HE ADVISED ME TO CHECK THE OIL LEVEL REGULARLY. I NOTICED THAT I HAD TO ADD A QUART OF OIL EVERY 1,000 MILES OR SO. I VOICED MY CONCERN TO THE SERVICE MANAGER WHEN I HAD MY FIRST OIL CHANGE AND WAS TOLD THAT "A QUART OF OIL LOSS PER 1,000 MILES IS NORMAL". I CHECKED MY OIL REGULARLY TO AVOID ANY PROBLEMS UNTIL ONE DAY, I FOUND OUT ABOUT OIL CONSUMPTION TESTS. I TOLD THE SERVICE MANAGER ABOUT IT AND HE ARRANGED TO HAVE IT DONE ON MY NEXT OIL CHANGE. THE FIRST OIL CONSUMPTION TEST REVEALED ABNORMAL RESULTS WHICH PROMPTED THEM TO REPAIR THE PROBLEM. ANOTHER OIL CONSUMPTION TEST WAS DONE AND IT SHOWED A MORE FAVORABLE RESULT. I CHECK THE OIL LEVEL REGULARLY AND STILL NOTICE THAT I ADD A QUART OF OIL EVERY 1,000 MILES. I SPOKE TO THE SERVICE MANAGER ABOUT IT AND WAS TOLD THAT IT WAS NORMAL. I WENT TO ANOTHER DEALER TO HAVE THE OIL CONSUMPTION CHECKED. THE FIRST OIL CONSUMPTION TEST REVEALED A QUART OF OIL LOSS PER 1000 MILES AND THE SECOND TEST REVEALED AN ABNORMAL RESULT OF A QUART AND A QUARTER OIL LOSS PER 1000 MILES. I WAS THEN TOLD BY THE SERVICE REPRESENTATIVE TO CONTACT MITSUBISHI CORPORATE OFFICE TO REPORT THE RESULT. NOW I'M ASKING FOR YOUR ASSISTANCE IN SOLVING THIS PROBLEM. THANK YOU. *TR
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#10227112May 8, 2008
ELECTRICAL SYSTEM, STRUCTURE:FRAME AND MEMBERS
I HAD JUST ARRIVED FROM WORK AND PULLED-IN MY DRIVEWAY, I WAS IDLING MY CAR BEFORE SHUTTING OFF THE ENGINE. I THEN SWITCHED OFF MY HEADLIGHTS, BUT THE HEADLIGHTS STAYED ON. I THEN PROCEEDED TO TURN THE HEADLIGHT SWITCH ON, THEN OFF; AFTER SEVERAL ATTEMPTS THE HEADLIGHTS FINALLY SWITCHED OFF, BUT THEN, THE HEADLIGHTS, PARKLIGHTS, MARKERS AND EVEN THE LICENSE PLATE LIGHTS WOULD FLICKER UNTIL THE IGNITION WAS SWITCHED OFF AND PULLED OUT THE KEY, BUT JUST BEFORE THIS INCIDENT I USED MY WIPERS TO CLEAR MY WINDSHIELD OF RAIN/MIST WITH A ONE WIPE/MANUAL SWEEP AND THE WIPERS JUST SEEMED THAT IT DIDN'T WANT TO STOP WIPING UNTIL THE IGNITION WAS SWITCHED OFF AND THE KEY PULLED OUT. THIS IS THE FIRST INCIDENT AND IT WAS RAINING OR HAD JUST RAINED. THE DEALERSHIP THEN REPLACED BOTH LIGHT AND WIPER SWITCHES AFTER DETERMINING THAT THERE WAS A SHORT. THIS SEEMED TO ADDRESS AND CORRECT THE PROBLEMS. THEN ON APRIL 28, 2008 I HAD JUST ARRIVED AT WORK AND WAS IDLING MY CAR BEFORE SWITCHING THE IGNITION OFF, AS I SWITCHED OFF THE LIGHTS THE HORN STARTED GOING OFF CONTINUOUSLY. IF THE LIGHTS WERE LEFT IN THE ON OR PARK POSITION, THE HORN WOULD STOP, BUT WHEN THE LIGHT SWITCH WAS TURNED OFF, IT DIDN'T STOP GOING OFF EVEN WHEN THE IGNITION WAS OFF AND THE KEY PULLED OUT. IT ONLY STOPPED AFTER THE FUSE WAS PULLED OUT. AGAIN, THE WEATHER WAS RAINING OR HAD JUST RAINED. I THEN DROPPED OFF MY CAR AT THE DEALERSHIP AND THEY DETERMINED THAT WATER INTRUSION THROUGH THE DRIVER'S FRONT KICK PANEL TO JUNCTION BLOCK, INSTRUMENT HARNESS, FLOOR HARNESS AND CHASSIS HARNESS. CORROSION ON PINS AND CONNECTORS CAUSING FAILURES AND SHORTS TO ALL SYSTEMS. THEY HAD AN OUTSIDE VENDOR SEAL AROUND WIRING HARNESS BEHIND INNER FENDER WELL. AT THIS POINT NONE OF THE WIRINGS NOR HARNESS WERE REPLACED. I WAS INFORMED THAT THIS WOULD ALL BE CUSTOMER PAY AND NOT COVERED UNDER WARRANTY AS I HAVE EXCEEDED THE 3/36 WARRANTY PERIOD. WIPERS HORN AND REMOTE UN/LOCK DON'T WORK. *TR
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0

← Back to Mitsubishi Lancer Evolution