Mazda CX-5 Service Bulletins (2014)
789 manufacturer communications on file.
- August 18, 2014•Document ID: 10060493Service Bulletin/Repair InstructionsSTRUCTURE:BODY:DOOR
- Mfr Comm. #:
- 09-017-14
- Date Added:
- March 31, 2016
- Manufacturer:
- MAZDA
SummarySUMMARY TO BE PROVIDED ON A FUTURE DATE.
Associated Products (2)Associated Documents - August 15, 2014•Document ID: 10098367Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- 09-034-14-2956
- Date Added:
- May 5, 2017
- Manufacturer:
- MAZDA
SummaryIN ACCORDANCE WITH FEDERAL REGULATIONS, FOLLOW THE PROCEDURE LISTED BELOW WHEN REPLACING A SPEEDOMETER.NOTE:MAZDA VEHICLES ARE MANUFACTURED WITH TAMPER-PROOF SPEEDOMETERS.WHEN A SPEEDOMETER IS REPLACED, THE NEW SPEEDOMETER WILL READ ZERO (0) MILES.THIS PROCEDURE IS EXTREMELY IMPORTANT TO ACCURATELY REPRESENT ACTUAL VEHICLE MILEAGE.PRIOR TO SPEEDOMETER REMOVAL, COMPLETE THE INFORMATION REQUIRED ON THE SPEEDOMETER REPLACE-MENT LABEL. LABELS CAN ONLY BE ORDERED THROUGH MSTORE, NOT MDCS.
Associated Products (144)2015 Mazda CX-52015 Mazda CX-92015 Mazda Mazda32015 Mazda Mazda52015 Mazda Mazda62015 Mazda MX-52014 Mazda CX-52014 Mazda CX-92014 Mazda Mazda22014 Mazda Mazda32014 Mazda Mazda52014 Mazda Mazda62014 Mazda MX-52013 Mazda CX-52013 Mazda CX-92013 Mazda Mazda22013 Mazda Mazda32013 Mazda Mazda52013 Mazda Mazda62013 Mazda MX-5+ 124 moreAssociated Documents - July 29, 2014•Document ID: 10098324Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 06-002-14-2931
- Date Added:
- May 4, 2017
- Manufacturer:
- MAZDA
SummarySOME VEHICLES MAY EXHIBIT AN UNUSUAL (CLACKING) NOISE FROM UNDER THE FRONT OF THE VEHICLE. THIS NOISE ONLY OCCURS WHEN STARTING TO MOVE THE VEHICLE WHILE THE STEERING WHEEL IS TURNED TO THE FULL LEFT POSITION. NOTE:THE NOISE WILL NOT OCCUR IF THE STEERING WHEEL IS IN THE CENTER OR FULL RIGHT POSITION.THE NOISE IS CAUSED WHEN THE EDGE OF THE LEFT SIDE INNER BALL JOINT (A) GETS STUCK WITH THE STEERING GEAR HOUSING. THE FOLLOWING MODIFICATIONS HAVE BEEN MADE TO ELIMINATE THE NOISE:1. THE SHAPE OF THE INNER BALL JOINT EDGE HAS BEEN CHANGED.2. GREASE HAS BEEN APPLIED TO THE INNER BALL JOINT EDGE.
Associated Products (5)Associated Documents - July 16, 2014•Document ID: 10098341Service Bulletin/Repair InstructionsWHEELS
- Mfr Comm. #:
- 03-003-14-2941
- Date Added:
- May 4, 2017
- Manufacturer:
- MAZDA
SummarySOME VEHICLES MAY EXHIBIT A GROAN TYPE NOISE FROM THE FRONT WHEEL HUB BEARING WHILE DRIVING AT HIGH SPEED OR WHEN CORNERING. THIS MAY BE CAUSED BY FRONT WHEEL HUB BEARING CORROSION.
Associated Products (4)Associated Documents - July 16, 2014•Document ID: 10098329Service Bulletin/Repair InstructionsSEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER
- Mfr Comm. #:
- 09-033-14-2944
- Date Added:
- May 4, 2017
- Manufacturer:
- MAZDA
SummarySOME VEHICLES MAY EXHIBIT AN INOPERATIVE SEAT WARMER (OR SEAT HEATER) ON THE DRIVER AND/OR PASSENGER SEAT. WHEN WEIGHT IS APPLIED TO THE SEAT, PART OF THE HEATER ELEMENT WIRE MAY COME OUT OF POSITION AND BECOME BENT. UNDER REPEATED STRESS, THE WIRE MAY BREAK CAUSING AN INOPERATIVE SEAT WARMER CONDITION.AN ADDITIONAL ADHESION TREATMENT HAS BEEN APPLIED TO ELIMINATE THE HEATER ELEMENT WIRE FROM COMING OUT OF THE POSITION.
Associated Products (3)Associated Documents - July 16, 2014•Document ID: 10061516Service Bulletin/Repair InstructionsWHEELS
- Mfr Comm. #:
- 03-003-14
- Date Added:
- April 12, 2016
- Manufacturer:
- MAZDA
SummarySUMMARY TO BE PROVIDED ON A FUTURE DATE.
Associated Products (3)Associated Documents - July 16, 2014•Document ID: 10060534Service Bulletin/Repair InstructionsSEATS
- Mfr Comm. #:
- 09-033-14
- Date Added:
- March 31, 2016
- Manufacturer:
- MAZDA
SummarySUMMARY TO BE PROVIDED ON A FUTURE DATE.
Associated Products (3)Associated Documents - July 14, 2014•Document ID: 10098343Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 05-008-14-2920
- Date Added:
- May 4, 2017
- Manufacturer:
- MAZDA
SummarySOME VEHICLES MAY EXHIBIT ONE OF THE FOLLOWING CONCERNS:HARD TO SHIFT INTO 3RD GEARSOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H)THIS IS CAUSED BY THE FRICTION COEFFICIENT BETWEEN THE 3/4 CLUTCH HUB AND THE SLEEVE INCREASING. A SURFACE TREAT-MENT HAS NOW BEEN ADDED TO THE 3/4 CLUTCH HUB TO DECREASE THE FRICTION COEFFICIENT.
Associated Products (8)Associated Documents - July 14, 2014•Document ID: 10059731Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 05-008-14
- Date Added:
- March 16, 2016
- Manufacturer:
- MAZDA
SummarySUMMARY TO BE PROVIDED ON A FUTURE DATE.
Associated Products (8)Associated Documents - July 8, 2014•Document ID: 10098354Service Bulletin/Repair InstructionsVISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM
- Mfr Comm. #:
- 07-001-14-2937
- Date Added:
- May 4, 2017
- Manufacturer:
- MAZDA
SummaryWHEN SELECTING THE DEFROSTER VENTS POSITION (B) WITH THE MODE SELECTOR DIAL (A), SOME CUSTOMERS MAY NOTICE THE DIAL DOES NOT STAY IN THE DEFROSTER VENTS POSITION AND RETURNS TO THE DEFROSTER/FLOOR VENTS POSITION (C). THIS CONCERN MAY BE DUE TO A PRODUCTION VARIATION. SOME OF THE MODE CONTROL WIRES (A) MAY BE TOO LONG TO TRANSMIT MOVEMENT FROM THE MODE SELECTOR DIAL TO THE LINK (B). THE LENGTH OF THE MODE CONTROL WIRE HAS BEEN SHORTENED TO ELIMINATE THIS CONCERN.
Associated Products (3)Associated Documents - July 8, 2014•Document ID: 10059741Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- 07-001-14
- Date Added:
- March 16, 2016
- Manufacturer:
- MAZDA
SummarySUMMARY TO BE PROVIDED ON A FUTURE DATE.
Associated Products (3)Associated Documents - June 27, 2014•Document ID: 10098222Service Bulletin/Repair InstructionsSTRUCTURE:BODY:HOOD:HINGE AND ATTACHMENTS
- Mfr Comm. #:
- 09-028-14-2942
- Date Added:
- May 4, 2017
- Manufacturer:
- MAZDA
SummarySOME VEHICLES MAY EXHIBIT A CONDITION WHERE THE HOOD VIBRATES WHEN DRIVING AT SPEEDS OF 110 KM/H (68 MPH) OR MORE.THE AMOUNT OF SEALANT USED TO FILL IN THE SPACE BETWEEN THE INNER FRAME AND OUTER PANEL AT THE BOTTOM AREA OF THE HOOD IS INSUFFICIENT. IF THE SEALANT DETACHES (AS SHOWN BELOW ON THE LEFT), IT MAY CAUSE THE HOOD TO VIBRATE. THE AMOUNT OF SEALANT HAS BEEN INCREASED DURING VEHICLE PRODUCTION AND THE PRELOAD FORCE OF THE COWL GRILL SEAL HAS BEEN INCREASED TO ELIMINATE THE CONCERN.
Associated Products (2)Associated Documents - June 27, 2014•Document ID: 10060524Service Bulletin/Repair InstructionsSTRUCTURE:BODY:HOOD
- Mfr Comm. #:
- 09-028-14
- Date Added:
- March 31, 2016
- Manufacturer:
- MAZDA
SummarySUMMARY TO BE PROVIDED ON A FUTURE DATE.
Associated Products (2)Associated Documents - June 20, 2014•Document ID: 10061482Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- RF-14-06R
- Date Added:
- April 12, 2016
- Manufacturer:
- MAZDA
SummarySUMMARY TO BE PROVIDED ON A FUTURE DATE.
Associated Products (3)Associated Documents - June 10, 2014•Document ID: 10098302Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR
- Mfr Comm. #:
- 09-026-14-2934
- Date Added:
- May 4, 2017
- Manufacturer:
- MAZDA
SummarySOME VEHICLES MAY EXHIBIT A VIBRATION FROM THE DRIVER-SIDE POWER DOOR MIRROR GLASS WHEN THE VEHICLE IS DRIVEN AT HIGH SPEEDS. THIS CONCERN MAY BE DUE TO A LACK OF RIGIDITY OF THE MIRROR BASE SO THE MIRROR VIBRATES WHEN IT RECEIVES VEHICLE VIBRATION OR WIND PRESSURE.AN ADDITIONAL REINFORCEMENT HAS BEEN INSTALLED INSIDE THE DOOR TO INCREASE THE DOOR PANEL STRENGTH WHERE THE DOOR MIRROR IS MOUNTED. ALSO, THE DOOR MIRROR SHAPE HAS BEEN CHANGED. BOTH OF THESE MODIFICATIONS HAVE BEEN IMPLEMENTED TO ELIMINATE MIRROR GLASS VIBRATION CONCERNS.
Associated Products (3)Associated Documents - June 10, 2014•Document ID: 10098282Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- 09-027-14-2935
- Date Added:
- May 4, 2017
- Manufacturer:
- MAZDA
SummaryTHIS SERVICE BULLETIN PROVIDES INFORMATION REGARDING THE PROPER USE OF THE DRIVERS FLOOR MAT TO AVOID ANY POTENTIAL INTERFERENCE WITH THE FOOT PEDALS. THE FOLLOWING ARE POSSIBLE CAUSES OF FLOOR MAT INTERFERENCE, WHICH CAN BE AVOIDED WITH PROPER USAGE. FLOOR MAT MOVES FORWARD DUE TO IMPROPER INSTALLATION. INAPPROPRIATE FLOOR MAT (SUCH AS AFTERMARKET, NON-FACTORY-EQUIPPED, OR NON-GENUINE) IS USED. FLOOR MAT IS STACKED ONE ON TOP OF ANOTHER.
Associated Products (121)2015 Mazda CX-52015 Mazda CX-92015 Mazda Mazda22015 Mazda Mazda32015 Mazda Mazda52015 Mazda Mazda62015 Mazda MX-52014 Mazda CX-52014 Mazda CX-92014 Mazda Mazda22014 Mazda Mazda32014 Mazda Mazda52014 Mazda Mazda62014 Mazda MX-52013 Mazda CX-52013 Mazda CX-92013 Mazda Mazda22013 Mazda Mazda32013 Mazda Mazda52013 Mazda Mazda6+ 101 moreAssociated Documents - June 10, 2014•Document ID: 10098245Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 00-002-14-2936
- Date Added:
- May 4, 2017
- Manufacturer:
- MAZDA
SummaryMAZDA NORTH AMERICAN OPERATIONS RECEIVED MANY REQUESTS FROM OUR DEALERS ASKING US TO APPROVE ADDITIONAL ON-CAR BRAKE LATHES AS AN OPTION FOR MNAO AUTHORIZED EQUIPMENT. DUE TO YOUR FEEDBACK AND AFTER EVALUATING A FEW ON-CAR BRAKE LATHES, WE ARE PLEASED TO ANNOUNCE THAT WE HAVE ADDED THE PRO CUT ON-CAR BRAKE LATHE TO MNAO AUTHORIZED EQUIPMENT PROGRAM. THE ACCU-TURN IS STILL AN APPROVED BRAKE LATHE BUT IT IS NO LONGER AVAILABLE FOR PURCHASE FROM OUR VENDOR. IMPORTANT REMINDER ROTORS MUST BE MACHINED USING A MAZDA APPROVED ON-CAR BRAKE LATHE OR WARRANTY CLAIMS ARE SUBJECT TO DENIAL OR DEBIT.
Associated Products (121)2015 Mazda CX-52015 Mazda CX-92015 Mazda Mazda22015 Mazda Mazda32015 Mazda Mazda52015 Mazda Mazda62015 Mazda MX-52014 Mazda CX-52014 Mazda CX-92014 Mazda Mazda22014 Mazda Mazda32014 Mazda Mazda52014 Mazda Mazda62014 Mazda MX-52013 Mazda CX-52013 Mazda CX-92013 Mazda Mazda22013 Mazda Mazda32013 Mazda Mazda52013 Mazda Mazda6+ 101 moreAssociated Documents - June 10, 2014•Document ID: 10060519Service Bulletin/Repair InstructionsSTRUCTURE:BODY:DOOR
- Mfr Comm. #:
- 09-026-14
- Date Added:
- March 31, 2016
- Manufacturer:
- MAZDA
SummarySUMMARY TO BE PROVIDED ON A FUTURE DATE.
Associated Products (3)Associated Documents - June 4, 2014•Document ID: 10055503Service Bulletin/Repair InstructionsBACK OVER PREVENTION: CAMERA SYSTEM
- Mfr Comm. #:
- 09-016/14
- Date Added:
- June 4, 2014
- Manufacturer:
- MAZDA
SummarySOME VEHICLES MAY HAVE INOPERATIVE REAR MOUNT CAMERA. DUE TO WATERING ENTERING THE CAMERA FROM A HIGH PRESSURE CAR WASH. 06/04/14*LJ
Associated Products (2)Associated Documents - May 30, 2014•Document ID: 10098065Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- 09-022-14-2921A
- Date Added:
- May 1, 2017
- Manufacturer:
- MAZDA
SummarySOME CUSTOMERS MAY EXPERIENCE AN ELECTRICAL MALFUNCTION AFTER A VEHICLE BODY REPAIR. THE NEWLY PAINTED FENDER STAY (B) MAY BE CAUSING A POOR FRONT HARNESS (A) GROUND CONNECTION.
Associated Products (6)Associated Documents