Jeep Wagoneer Service Bulletins
936 manufacturer communications on file.
- September 13, 2022•Document ID: 10226030Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 0817122
- Date Added:
- November 7, 2022
- Manufacturer:
- JEEP
SummaryFlash: Battery Pack Control Module (BPCM) Diagnostic and System Updates This bulletin involves updating the BPCM with the latest available software. Customers may experience a false Malfunction Indicator Lamp (MIL) illumination related to: P0B42-00 - Hybrid/EV Battery Voltage Sense 2 Circuit Low. Customer may also notice:Start/Stop inoperative. Vehicle behaves like it is always operating in gas mode.
Associated Products (1)Associated Documents - September 12, 2022•Document ID: 10225985Service Bulletin/Repair InstructionsSEAT BELTS; SEAT BELTS:REAR/OTHER:RETRACTOR
- Mfr Comm. #:
- S2223000067
- Date Added:
- November 7, 2022
- Manufacturer:
- JEEP
Summary3RD Row Seat Does Not Lock In Up Right Position.
Associated Products (3)Associated Documents - September 8, 2022•Document ID: 10225950Service Bulletin/Repair InstructionsPOWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); UNKNOWN OR OTHER
- Mfr Comm. #:
- 9100063
- Date Added:
- November 7, 2022
- Manufacturer:
- JEEP
SummaryPCM If you are replacing a PCM in this vehicle, please review SOL S2225000003 for detailed programming instructions. Failure to follow instructions may result in an unresponsive PCM and cannot be recovered.
Associated Products (2)Associated Documents - September 6, 2022•Document ID: 10225948Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS; UNKNOWN OR OTHER
- Mfr Comm. #:
- 9100061
- Date Added:
- November 7, 2022
- Manufacturer:
- JEEP
SummaryHEADLAMP ASSY Please contact engineer FCA Redacted Content prior to replacing, if no response within 15 minutes proceed with repair.
Associated Products (3)Associated Documents - September 3, 2022•Document ID: 10225980Service Bulletin/Repair InstructionsUNKNOWN OR OTHER; EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE
- Mfr Comm. #:
- S228A000025
- Date Added:
- November 7, 2022
- Manufacturer:
- DODGE
SummaryHarman R1H Uconnect 5 Radio Software Flash Error Codes
Associated Products (10)Associated Documents - September 3, 2022•Document ID: 10225977Service Bulletin/Repair InstructionsUNKNOWN OR OTHER; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.
- Mfr Comm. #:
- S228A000024
- Date Added:
- November 7, 2022
- Manufacturer:
- CHRYSLER
SummaryRadio Sirius XM Mutes After Ending Phone Call
Associated Products (9)Associated Documents - September 2, 2022•Document ID: 10225979Service Bulletin/Repair InstructionsELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); SUSPENSION; ELECTRICAL SYSTEM; ELECTRONIC STABILITY CONTROL (ESC):CONTROL MODULE
- Mfr Comm. #:
- S1902000008
- Date Added:
- November 7, 2022
- Manufacturer:
- JEEP
SummaryAir Suspension Compressor Module Assembly Replacement.
Associated Products (5)Associated Documents - September 1, 2022•Document ID: 10225974Service Bulletin/Repair InstructionsBACK OVER PREVENTION; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; UNKNOWN OR OTHER
- Mfr Comm. #:
- S2223000065
- Date Added:
- November 7, 2022
- Manufacturer:
- JEEP
SummaryBuzz, Rattle Noise From Upper Instrument Panel Near Speaker.
Associated Products (2)Associated Documents - September 1, 2022•Document ID: 10225973Service Bulletin/Repair InstructionsAIR BAGS; AIR BAGS:SRS MALFUNCTION WARNING LAMP/LIGHT
- Mfr Comm. #:
- S228A000023
- Date Added:
- November 7, 2022
- Manufacturer:
- RAM
SummaryErroneous Email Or Mobile App Message Notification For Airbag Light On
Associated Products (8)Associated Documents - August 27, 2022•Document ID: 10229578Service Bulletin/Repair InstructionsPARKING BRAKE; AIR BAGS
- Mfr Comm. #:
- 2303522
- Date Added:
- January 9, 2023
- Manufacturer:
- JEEP
SummaryFront Row Seat Back Panel Loose This bulletin involves inspecting the front row seat back panels. Check for loose upper and lower panels. If needed the panels will need to be removed and inspected for broken clips and replaced if needed. Check the seat back and upper screen bezel for large gaps and loose panels Verify the Rear Seat Entertainment (RSE) screen bezel installation by checking visually and running hand over the seam checking gap and flushness. Gap should not exceed 1.5mm. Verify with feeler gage if necessary. Cap (bezel) should be flush to back panel. With both thumbs positioned on cap (bezel), simultaneously push upwardsto verify engagement. Cap (bezel) should stay engaged Fig. 1.Upper Seat Back (Bezel) Verify the front seat back panel installation is correct. From the rear seat area place both hands near top of back panel and with fingers slightly engaged into back panel gently pull to verify back panelis correctly installed. There should be no movement in the back panel from this direction. To verify engagement of lower part of back panel, grab rear lower sides and gently pull at same time. Back panel should not show any signs of movement Fig. 2.Seat Back Inspection Were there any loose panels or large gaps found in the upper or lower panels? This inspection needs to be performed on both the driver's and passenger's front seat back. YES>>>Proceed to Step 1 of the Repair Procedure. NO>>>This bulletin has been completed. Use inspection LOP (23-20-34-96) to close the active RSU.
Associated Products (2)Associated Documents - August 27, 2022•Document ID: 10225430Service Bulletin/Repair InstructionsSEATS
- Mfr Comm. #:
- 2303522
- Date Added:
- October 31, 2022
- Manufacturer:
- JEEP
SummaryFront Row Seat Back Panel Loose This bulletin involves inspecting the front row seat back panels. Check for loose upper and lower panels. If needed the panels will need to be removed and inspected for broken clips and replaced if needed. Check the seat back and upper screen bezel for large gaps and loose panels Verify the Rear Seat Entertainment (RSE) screen bezel installation by checking visually and running hand over the seam checking gap and flushness. Gap should not exceed 1.5mm. Verify with feeler gage if necessary. Cap (bezel) should be flush to back panel. With both thumbs positioned on cap (bezel), simultaneously push upwardsto verify engagement. Cap (bezel) should stay engaged Fig. 1.Upper Seat Back (Bezel) Verify the front seat back panel installation is correct. From the rear seat area place both hands near top of back panel and with fingers slightly engaged into back panel gently pull to verify back panelis correctly installed. There should be no movement in the back panel from this direction. To verify engagement of lower part of back panel, grab rear lower sides and gently pull at same time. Back panel should not show any signs of movement Fig. 2.Seat Back Inspection Were there any loose panels or large gaps found in the upper or lower panels? This inspection needs to be performed on both the driver's and passenger's front seat back. YES>>>Proceed to Step 1 of the Repair Procedure. NO>>>This bulletin has been completed. Use inspection LOP (23-20-34-96) to close the active RSU.
Associated Products (2)Associated Documents - August 27, 2022•Document ID: 10225293Service Bulletin/Repair InstructionsUNKNOWN OR OTHER; SEATS; EQUIPMENT
- Mfr Comm. #:
- 2303522
- Date Added:
- October 31, 2022
- Manufacturer:
- JEEP
SummaryFront Row Seat Back Panel Loose This bulletin involves inspecting the front row seat back panels. Check for loose upper and lower panels. If needed the panels will need to be removed and inspected for broken clips and replaced if needed. Check the seat back and upper screen bezel for large gaps and loose panels Verify the Rear Seat Entertainment (RSE) screen bezel installation by checking visually and running hand over the seam checking gap and flushness. Gap should not exceed 1.5mm. Verify with feeler gage if necessary. Cap (bezel) should be flush to back panel. With both thumbs positioned on cap (bezel), simultaneously push upwardsto verify engagement. Cap (bezel) should stay engaged Fig. 1.Upper Seat Back (Bezel) Verify the front seat back panel installation is correct. From the rear seat area place both hands near top of back panel and with fingers slightly engaged into back panel gently pull to verify back panelis correctly installed. There should be no movement in the back panel from this direction. To verify engagement of lower part of back panel, grab rear lower sides and gently pull at same time. Back panel should not show any signs of movement Fig. 2.Seat Back Inspection Were there any loose panels or large gaps found in the upper or lower panels? This inspection needs to be performed on both the driver's and passenger's front seat back. YES>>>Proceed to Step 1 of the Repair Procedure. NO>>>This bulletin has been completed. Use inspection LOP (23-20-34-96) to close the active RSU.
Associated Products (2)Associated Documents - August 26, 2022•Document ID: 10229510Service Bulletin/Repair InstructionsELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); SUSPENSION
- Mfr Comm. #:
- S2202000009
- Date Added:
- January 9, 2023
- Manufacturer:
- JEEP
SummaryClunking Noise From Front Suspension Over Bumps, Rough Road, Or Chassis Roll.
Associated Products (2)Associated Documents - August 26, 2022•Document ID: 10225367Service Bulletin/Repair InstructionsSUSPENSION
- Mfr Comm. #:
- S2202000009
- Date Added:
- October 31, 2022
- Manufacturer:
- JEEP
SummaryClunking Noise From Front Suspension Over Bumps, Rough Road, Or Chassis Roll.
Associated Products (2)Associated Documents - August 26, 2022•Document ID: 10225230Service Bulletin/Repair InstructionsSUSPENSION
- Mfr Comm. #:
- S2202000009
- Date Added:
- October 31, 2022
- Manufacturer:
- JEEP
SummaryClunking Noise From Front Suspension Over Bumps, Rough Road, Or Chassis Roll.
Associated Products (2)Associated Documents - August 25, 2022•Document ID: 10229501Service Bulletin/Repair InstructionsPOWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
- Mfr Comm. #:
- S2225000003
- Date Added:
- January 9, 2023
- Manufacturer:
- JEEP
SummaryP0513-Invalid Skim Key setting in the PCM after programming a replacement ?generic? PCM
Associated Products (2)Associated Documents - August 25, 2022•Document ID: 10225358Service Bulletin/Repair InstructionsPOWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
- Mfr Comm. #:
- S2225000003
- Date Added:
- October 31, 2022
- Manufacturer:
- JEEP
SummaryP0513-Invalid Skim Key setting in the PCM after programming a replacement ?generic? PCM
Associated Products (2)Associated Documents - August 25, 2022•Document ID: 10225221Service Bulletin/Repair InstructionsPOWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
- Mfr Comm. #:
- S2225000003
- Date Added:
- October 31, 2022
- Manufacturer:
- JEEP
SummaryP0513-Invalid Skim Key setting in the PCM after programming a replacement ?generic? PCM
Associated Products (2)Associated Documents - August 24, 2022•Document ID: 10229575Service Bulletin/Repair InstructionsEXTERIOR LIGHTING; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 0816322
- Date Added:
- January 9, 2023
- Manufacturer:
- JEEP
SummaryFlash: Memory Seat Module (MSM) Updates This bulletin involves reprogramming the MSM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC). B1D9B-54 - Seat Horizontal Front Stop Not Learned-Missing Calibration. Customers may experience the following:Memory seat do not save on profiles 1 or 2. Easy entry/exit functionality is inoperative.
Associated Products (2)Associated Documents - August 24, 2022•Document ID: 10225427Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; SEATS
- Mfr Comm. #:
- 0816322
- Date Added:
- October 31, 2022
- Manufacturer:
- JEEP
SummaryFlash: Memory Seat Module (MSM) Updates This bulletin involves reprogramming the MSM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC). B1D9B-54 - Seat Horizontal Front Stop Not Learned-Missing Calibration. Customers may experience the following:Memory seat do not save on profiles 1 or 2. Easy entry/exit functionality is inoperative.
Associated Products (2)Associated Documents