GMC · Model Report
Showing safety data for the 1999 model year only.
DOPE, INC. IS RECALLING 42,540 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.
CERTAIN FEDERAL-MOGUL REPLACEMENT WHEEL HUB ASSEMBLIES WITH THE BRAND NAMES: NATIONAL, CARQUEST P/NOS. 515020, 515021, 515025, 515053, 515054, 515059, AND 515060, SHIPPED BETWEEN JANUARY 23, 2006, AND DECEMBER 20, 2007, SOLD FOR LIGHT DUTY AND MEDIUM DUTY TRUCKS. THE INBOARD RETENTION NUT USED TO MAINTAIN HUB BEARING ASSEMBLY CAN LOOSEN RESULTING IN AN ABS LIGHT INDICATION, NOISE, AND/OR WHEEL SEPARATION.
CERTAIN HONEYWELL FRAM RACING BRAND HP4 AND HP8 OIL FILTERS THAT WERE MANUFACTURED FROM MAY 25, 2006, THROUGH SEPTEMBER 14, 2007, AND SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR VEHICLES LIST ABOVE. THE AFFECTED FILTERS ARE MARKED WITH A DATE CODE A61451 THROUGH A72571 SEQUENTIALLY. THE DATE CODE AND PART NUMBER APPEAR ON THE FILTER HOUSING. FRAM RACING HP4 AND HP8 OIL FILTERS NOT BEARING A DATE CODE IN THIS RANGE ARE NOT AFFECTED BY THIS RECALL. THE GASKET OF THE OIL FILTER BECOMES MORE PLIABLE UNDER HIGH TEMPERATURES AND PRESSURES.
CERTAIN CEQUENT 90 DEGREE 7-WAY RIGHT ANGLE ADAPTORS SOLD BY DISTRIBUTORS IN TOW PACKAGES FOR AFTERMARKET SALES TO TOW 5TH WHEEL RV TRAVEL TRAILERS. DUE TO INCORRECT WIRING OF THE HARNESS, THE TRAILER LIGHTS MAY NOT OPERATE PROPERLY.
CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE.
ABS Brakes cut out leaving you with little to no brakes. No warning light appears. This continues on and off over time. Then that ABS warning light came on. When the warning light was on, brakes worked just not ABS. Light would go out and back to the original issue. Took it in to dealership when the light remained on. They reset the light and told me every thing was fine. And charged me $$$. ABS Brake warning light can right back on. Had the manager drive it. Told me it was fine, brakes worked well. The ABS warning would go in and out. Removed the ABS fuse, so I could depend on being able to stop, without having to worry about the ABS cutting in and out for a few years. Watched for recalls, nothing appeared. Noticed on blogs, others were having the same issue. Took it to a great mechanic! Who verified there were no leaks in the brake lines, replaced one line that had been known to have issues on this type of truck and verified there were no air bubbles on the lines. Still same issue, then replaced the computer system for the ABS. No codes ever came up on the computer system that I can recall. Had more issues with the ABS. Would go to stop, (generally on a hill) then when it came to the final stopping, I had NO BRAKES, had to slam on the brakes to stop. ABS Brake warning lights never came on. My mechanic looked and looked and relooked into this. Found from others that blogged that they had similar issues, that one or both of the ABS Brake sensors were not responding evenly causing an issue. Changed out the sensor. All is good now. This issues could have put and my family in danger a number of times. I was blessed to avoid a few accidents by driving far enough behind people and or had an emergency line to pull into when unable to stop. Hope a recall comes soon for these issues to prevent someone from being killed. These took place from about 2015-fixed 2020. Email me with a report number and where I can upload info at a later date, I will do so.
No injuries · No fire · No crash
I WAS DRIVING HOME FROM WORK ON 421 IN EMINENCE, KY. I PUSHED THE BRAKE PEDAL & I HAD NO BRAKES RIGHT IN FRONT OF HARRY HILL PARK. GM & I ARE VERY LUCKY THAT NO ONE WAS KILLED YESTERDAY. THE BRAKE LINE CORRODED & LEAKED THE BRAKE FLUID, SO WHEN I PUSHED THE PEDAL, IT WENT RIGHT TO THE FLOOR. THE VEHICLE IS PRETTY CLEAN & AFTER CHECKING MANY BLOGS & YOUTUBE VIDEOS THIS IS A VERY COMMON PROBLEM ON GM TRUCKS. I CHECKED THE RECALLS ON THIS TRUCK & THE TAILGATE CABLE IS RECALLED FOR BREAKING UNDER LOAD DUE TO CORROSION; THIS COULD INJURE SOMEBODY, BUT NOT AS VITAL COMPARED TO THE BRAKING SYSTEM AS SOMEONE COULD DIE IN A HORRIBLE INCIDENT. I WOULD GREATLY APPRECIATE YOUR ATTENTION TO THIS SERIOUS MATTER. THANK YOU
No injuries · No fire · No crash
I GOT UNDER THE TRUCK TO CHANGE THE OIL THEN I NOTICED A CRACK IN THE FRAME WHERE THE CROSS MEMBER IS. CROSS MEMBER RUNS ACROSS FRAME SUPPORT
No injuries · No fire · No crash
TL* THE CONTACT OWNS A 1999 GMC SIERRA 1500. WHILE DRIVING ON A COUNTRY ROAD THAT WAS ROCKY AND BUMPY, THE CONTACT LOST CONTROL OF THE VEHICLE. AS A RESULT, THE CONTACT DROVE INTO A DITCH AND CRASHED INTO A TREE. THE DRIVER'S SIDE FRONTAL AIR BAG PARTIALLY DEPLOYED, BUT FAILED TO PREVENT THE CONTACT'S HEAD FROM MAKING CONTACT WITH THE STEERING WHEEL. THE CONTACT SUSTAINED HEAD INJURIES THAT REQUIRED MEDICAL TREATMENT. A POLICE REPORT WAS NOT FILED. THE VEHICLE WAS NOT DIAGNOSED BY AN INDEPENDENT MECHANIC OR DEALER. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE TO DETERMINE IF THEY COULD INVESTIGATE. THE VEHICLE REMAINED PARKED AT THE CONTACT'S RESIDENCE. THE APPROXIMATE FAILURE MILEAGE WAS 166,000.
I PURCHASED THIS TRUCK A FEW MONTHS AGO. WITHIN A WEEK I HAD A CO WORKER POINT OUT THE BED WAS LEANING TOWARD THE CAB. A FEW WEEKS LATER WE GOT UNDER THE TRUCK TO FIND OUT WHAT WAS GOING ON. WE NOTICED ALOT OF RUST. I LOOKED ON LINE TO SEE HOW TO FIX IT AND FOUND ALOT OF PEOPLE WERE DEALING WITH THE SAME ISSUE. I DECIDED TO GET SOME SHEET METAL AND WELD IT TO THE FRAME. I THEN ASKED MY BOSS WHO OWNS A WELDER IF HE COULD HELP ME WITH IT. HE SAID THERE WASN'T ANYTHING LEFT TO WELD TO. THEN THE TRUCK STARTED NOT GOING INTO PARK. AND TO START IT YOU'D HAVE TO START IT IN NEUTRAL AND IT WOULD NOT STAY IN PARK, IT WOULD ROLL AND THE EMERGENCY BRAKE NO LONGER WORKED. I THEN HAD MY PARENTS TO TAKE THE TRUCK TO A BODY SHOP TO SEE IF THEY COULD REPAIR IT. BOTH BODY SHOPS SAID IT WAS NOT REPAIRABLE THAT THE FRAME WAS RUSTED OUT AND NEEDED REPLACED. ONE SHOP SAID THAT THE PARKING ISSUE COULD BE FROM THE FRAME BENDING, BUT DID NOT KNOW WITHOUT GETTING INTO THAT. THEY ALSO TOLD THEM THAT THE TRUCK WAS UNSAFE TO BE ON THE ROAD. I FINANCED THIS TRUCK FOR $5500 AND NOW I'M PAYING PAYMENTS ON A TRUCK I CAN'T EVEN USE.
No injuries · No fire · No crash