Ford · Model Report
Showing safety data for the 1988 model year only.
DOPE, INC. IS RECALLING 42,540 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.
SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.
K2 MOTOR IS RECALLING 1,921 AFTERMARKET HEADLAMPS OF VARIOUS MODELS SOLD FOR USE ON THE ABOVE LISTED VEHICLES. THESE HEADLAMPS ARE MISSING THE AMBER SIDE REFLEX REFLECTOR WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."
CERTAIN CK MOTORSPORTS COMBINATION HEADLIGHTS, CLEAR CORNER, BUMPER, AND SIDE MARKER LIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON THE PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
THE IGNITION SWITCH COULD EXPERIENCE AN INTERNAL SHORT CIRCUIT.
The contact owns a 1988 Ford Mustang. The contact stated while adding air to the tires, the radiator exploded in the engine. The contact stated there was no warning light illuminated. The vehicle was not taken to a local dealer nor an independent mechanic to be diagnosed. The vehicle was not yet repaired. The manufacturer was not informed of the failure. The failure mileage was approximately 5,000.
No injuries · No fire · No crash
I WAS DRIVING TO A FUNERAL HOME TO PICK UP ASHES 40 MILES FROM HOME WITH TWO CHOW DOGS WHEN THE STEERING COLUMN STARTED SMOKING AND WAS BURNING. THE VEHICLE STALLED OUT AND I PULLED TO THE SIDE OF THE ROAD. I CONTACTED AAA TO HAVE THE CAR TOWED TO A RELIABLE REPAIR SHOP. I HAD A USED ONE INSTALLED AS THE FORD DEALER SAID THE COMPUTER DOES NOT GO BACK TO THAT YEAR FOR PARTS. I DID NOT KNOW ABOUT THE RECALL AT THAT TIME. HOWEVER I FOUND OUT HOW TO FIND OUT DUE TO A GOOD MORNING AMERICA SHOW. I CONTACTED THE LOCAL FORD DEALER THIS TIME IN PERSON AND AGAIN COMPUTER COULD NOT GIVE ANY INFORMATION.THE PERSON IN CHARGE WAS JOHN LARUE AND HE GAVE ME A PHONE NUMBER TO FORD 1-800-392-3673 AND I CALLED EXPLAINED THE SITUATION AND APPARENTLY THERE WAS NOTHING THEY COULD DO AS THERE MAY BE A BLANKET RECALL WHATEVER THAT IS AND NOTHING LISTED ON THEIR COMPUTER AND WAS BLOWN OFF. NOTHING . NADA. I BELIEVE THAT IF YOU SELL IT YOU SERVICE IT IF IT IS DEFECTIVE. THIS IS MY REASON FOR THIS COMPLAINT. *TR
TL*THE CONTACT OWNS A 1988 FORD MUSTANG. WHILE DRIVING 60 MPH, THE VEHICLE BEGAN RIDING ROUGHLY AND THE ENGINE FAILED. THE CONTACT PULLED OUT OF TRAFFIC, WAITED TWENTY MINUTES, AND THEN RESTARTED THE VEHICLE. HE DROVE A BLOCK AND THE VEHICLE STOPPED AGAIN. THE VEHICLE HAD TO BE TOWED TO A MECHANIC. THE DIAGNOSIS WAS THAT THE IGNITION MODULE FAILED. THE CURRENT MILEAGE WAS 47,000.
No injuries · No fire · No crash
TL*THE CONTACT OWNS A 1988 FORD MUSTANG. THE VEHICLE WILL NOT PASS INSPECTION BECAUSE THE TURN SIGNALS AND HORN DO NOT WORK. THE DEALER WAS UNABLE TO CORRECT THE FAILURE BECAUSE THE MANUFACTURER DISCONTINUED THE PARTS. THE CURRENT MILEAGE WAS 19,400 AND FAILURE MILEAGE WAS 17,000.
No injuries · No fire · No crash
IGNITION SWITCH FAILURE IGNITION SWITCH WAS RECALLED AND REPLACED DURING NHTSA CAMPAIGN 96V071000. FORD PART #F29A-11572-DA. WIRING HARNESS END WAS ALSO REPAIRED DUE TO MELTING DURING OVERHEATING OF TERMINALS. THE SWITCH THAT WAS REPLACED DID NOT MELT OR FAIL INTERNALLY, BUT BECAME SEPARATED. THE ORIGINAL SWITCH AS WELL AS THE REPLACEMENT SWITCH IS MADE OF PLASTIC AND A LIGHT DUTY WHITE METAL THAT ARE CRIMPED ON THE ENDS TO CLOSE THE SWITCH. I FOUND THAT THE OLD SWITCH AS WELL AS THE NEW FAULTY SWITCH, BECAME SEPARATED. THE END CRIMPS SLOWLY BEND OPEN AND THE TOP OF THE SWITCH PUSHES AWAY FROM THE BASE. THIS SEPARATION SEEMS TO BE CAUSED BY THE INTERNAL SPRING PRESSURE ON THE SWITCH PLATES PUSHING ON THE BATTERY SIDE. THE METAL CRIMPS ARE NOT ABLE TO HOLD THE SWITCH CLOSED. THERE IS NO OTHER MECHANICAL FASTENERS HOLDING THIS SWITCH TOGETHER. THE INCREASED GAP BETWEEN THE CONTACT PLATES CAUSES AN OVERHEATING OF THE SWITCH, PRIMARILY AT THE BATTERY CONNECTORS, MELTING THE SWITCH AND HARNESS ASSEMBLY. MY FIRST SWITCH ONLY CAUSED DAMAGE TO THE HARNESS AND WIRES. BECAUSE I CHECKED INTO THE SMELL OF BURNING INSULATION IN THE COLUMN I DID NOT EXPERIENCE A FIRE OR SUBSTANTIAL DAMAGE. THIS TIME, I DID NOT SMELL ANYTHING, BUT LOST POWER TO MY TURN SIGNALS WHILE DRIVING THE CAR ON THE ROAD. WHEN I TRACED THE POWER LOSS I CAME TO THE IGNITION SWITCH AND FOUND THE HARNESS MELTING AGAIN AND THE SWITCH NEARLY SPLITTING IN HALF WHEN IT WAS UNBOLTED FROM THE COLUMN. AGAIN THE SWITCH OPENED UP AS THE METAL BASE GAVE WAY. *JB
No injuries · No fire · No crash