BMW i3 Complaints

237 consumer complaints on file.

#11772176October 19, 2026
STRUCTURE:BODY
The roof, which is constructed of carbon-based reinforced material, has been recently shown signs the delaminating.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11770251October 9, 2026
UNKNOWN OR OTHER, ELECTRICAL SYSTEM, BACK OVER PREVENTION: WARNINGS
The rear backup camera view in the screen is completely overridden in reverse, by a tire pressure warning when a tire is low or there is another TPMS fault. It requires using the rotary dial to clear the message before the function of the backup camera is restored. Also, if the rear hatch is unlatched by mistake (easy to do with the i3 key fob design) the rear camera, which is located in the rear bumper, is completely disabled.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11764977September 17, 2026
STRUCTURE:BODY
My 2017 i3 has a deteriorating roof. The roof, which is made of carbon fiber, is peeling and pieces are breaking off. This has also led to the interior upholstery of my roof to peel and sag. I am worried moisture will be let into my car, creating a mold issue. I contacted BMW and my extended warranty and they did not want to cover anything. They said this was normal wear and tear and they would not help me. From my understanding this is a much larger issue with all i3 models. I am also having a very hard time finding a body shop that will fix this for me. I have contacted several and they either don't know how to do it, or refuse to do it in fear that they might do it wrong. I am now considering contacting a a boat repair shop, but that might be very costly. I think the company is at fault and needs to figure out a solution. I take good care of my car and this is the only major issue I've ever had with it.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11761765September 2, 2026
STRUCTURE:BODY
The roof of the BMW started delaminating a few years back, and it is compromising the structural integrity of this vehicle. In an attempt to fix the roof, epoxy was applied after it was smoothed down and the roof looked aesthetically pleasing for about a year, until it started delaminating rapidly in the same spots. Now, the roof liner is starting to collapse, telling me that moisture is getting into the vehicle, further damaging the roof.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11753562July 29, 2026
STRUCTURE:BODY
The carbon fiber roof panel is starting to delaminate and I am concerned that pieces could fly off and cause an accident.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11751920July 21, 2026
ELECTRICAL SYSTEM, ENGINE, POWER TRAIN
The car has lost power on the highway multiple times and gone into Limp mode with no warnings on the dashboard. The Rex engine has failed to start as well. Very dangerous on the highway going 20 mph trying to make the next exit. The car has been back to the BMW dealer multiple times (over 2.5 months at the dealer ) with no repair. They are now offering to take the car in trade. The car is still under the EV warranty in California. Seems they and BMW engineering don’t know how to repair the car and are now putting the burden on the consumer.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11749626July 10, 2026
SUSPENSION
In the middle of driving, the coil spring on rear passenger side snapped. What happened to me today was exactly what the search result showed from the internet. And yet, when I put in my VIN # to your and BMW website, I got 0 recall for this VIN. Mine is 2015, what am I missing? Googel: Early BMW i3 models, particularly from the 2014-2016 production runs, have known issues with rear coil springs snapping, often due to corrosion or poor heat treatment. If your rear end sags, you hear a loud clank over bumps, or you notice a piece of metal resting near your rear tires, a broken spring is the likely culprit. Symptoms and inspection details include: The Snapping Point: The spring typically breaks at the very first or second coil from the bottom.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11746860June 27, 2026
STRUCTURE:BODY:ROOF AND PILLARS
On May 30, 2026, I was driving on the NJ Turnpike with high winds and I heard loud sounds like hard rain on the roof of my BMW i3. I saw sheets flying off the roof. When I parked the car, the clear coat covering the roof had delaminated, exposing the carbon fiber. The BMW collision shop told me that the roof panel has to be replaced and it is costly.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11745052June 18, 2026
FUEL/PROPULSION SYSTEM
After reviewing BMW’s warranty documentation, I believe that the part replaced — specifically the evaporative emissions (EVAP) valve or purge valve AND vapor canister (active charcoal canister) — should be covered under the California Extended Emissions Warranty (TZEV) for my 2018 BMW i3 with Range Extender. According to BMW’s California Emissions Warranty documentation (pages 14), the Evaporative Canister / Active Charcoal Filter is explicitly listed as a covered component under the Extended Emissions Warranty applicable to BMW i3 Range Extender vehicles in California. Furthermore, page 18 of the same document outlines the California Emission Control System Limited Warranty (TZEV), which provides coverage for emissions-related components for up to 15 years or 150,000 miles, whichever occurs first. Additionally, since we purchased this vehicle in 2021, we have meticulously maintained it and kept detailed fuel and service records. The vehicle has only been refueled NINE times total of 17 GALLONS of fuel with each refueling carefully logged by date and milage. The most recent refueling occurred on March 28, 2025, prior to our service visit at your dealership. These records demonstrate that the fuel and emissions systems have been minimally used, making premature failure of the vapor canister highly unusual. WE have never over filled the tank and dealer is claiming / assuming that is the cause. We believe this is a design flaw on BMW and we do pay the price. Many frustrated BMW i3 owners with similar issue and no help from BMW. THERE ARE MANY REPORTS OF THIS SAME ISSUE ALSO A BMW RECALL BULLETIN ( SIB 01 05 24 ) I3 REX EVAP SYSTEM PURGE VENT VALVE EXT LTD WTY PLEASE MAKE BMW TO RECALL / REPAY ALL I3 OWNERS WITH THIS ISSUE. WHAT IS THE POINT OF AN EXTENDED WARRANTY IF NO ONE IS ENFORCING IT !
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11743788June 12, 2026
AIR BAGS
Driver airbag warning light illuminated. Vehicle was diagnosed at BMW of Sherman Oaks (RO# 176741) and confirmed as a faulty driver airbag module - part# 32-30-6-870-366. BMW technician found fault code 930904: Driver's airbag interval stage 1, resistance too high stored. BMW NA declined goodwill repair assistance despite the failure occurring within 20 days of warranty expiration. This is a safety-critical federally mandated system. Multiple BMW i3 owners in online communities report the same issue and reference TSB SI B65 18 16 as a known defect related to a cable being too short. I believe this may be a widespread defect affecting 2014-2018 BMW i3 vehicles that warrants investigation.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11741143May 31, 2026
STRUCTURE:BODY
I bought the car new in 2017. Last summer, I noticed bubbles on the roof. On May 30, 2026, as I was driving 65 mph on the NJ Turnpike, I heard sounds on the roof like hard rain but it was not raining. I saw large sheets flying off my roof towards other cars, and some flying sheets were large enough to obscure a windshield. When I stopped, I saw more sheets hanging loose from the roof and I peeled off what I could. I think this is dangerous and understand it is common on BMW i3s (which are made of carbon fiber) and other BMW cars.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11737149May 11, 2026
POWER TRAIN, ENGINE, STEERING
This is an electric vehicle. I experienced a sudden loss of all power while traveling on the interstate in heavy traffic. I nearly lost control of the vehicle as it would not respond to my inputs. I had to cross two lanes of dense interstate traffic to get to a safe area to pull over and it was terrifying because the car just suddenly shut down while traveling at highway speeds. The dealership that I had the car towed to did some diagnostic work and said that "EME" had failed. The EME is the main processor that controls all electrical functions in the vehicle. My understanding is that 2019 BMW i3's were recalled due to failures of the EME due to corrosion. How my car was missed in that reacall, I can't ascertain. Perhaps because my particular car has an "S" designation, so it is called an "i3S" and it slipped through the cracks on the original recall. At any rate, the failure was catastrophic; it could have caused an accident and killed me. The car lost all power at highway speeds. Please look into why the i3S was overlooked in the original recall.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11737189May 11, 2026
POWER TRAIN, FUEL/PROPULSION SYSTEM, VEHICLE SPEED CONTROL
Sudden unintended deceleration on highway Complete loss of propulsion Thermal warning / overheating Date: May 11, 2026 Mileage: approximately 18,966+ Vehicle: 2014 BMW i3 REx, VIN [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11729647April 7, 2026
Chest Clip, Buckle, Harness, Other/I am not sure
We have experienced a mechanical issue with the harness system. Specifically, the straps become extremely difficult to tighten or loosen over time. To adjust them, I have to pull with the full force of a 200lb adult, to the point where it literally shakes the car. Despite following all manufacturer instructions—including cleaning the adjuster area and checking for twisted straps—the problem persists. Evenflo recently closed our support case (#00609796) and sent a replacement seat, which suggests an acknowledgement of the problem. Before I return the impacted seat (as Evenflo Requested), I wanted to reach out here promptly. I am particularly concerned because this appears to be a systemic issue. I would like to include this Reddit thread of other parents experiencing the same harness strap issue: Reddit Discussion: Evenflo 360 straps hard to tighten and loosen https://www.reddit.com/r/CPST/comments/1pzus73/evenflo_360straps_hard_to_tighten_and_loosen/ A cursory look at this Reddit thread shows at least 10 separate people with this same issue. I have documented interactions with Evenflo Parentlink via email and have photos attached and video link here. https://drive.google.com/file/d/1Ogbu8VN-45InQIfCxfnLJaeGgvzcRcRg/view?usp=sharing Thanks Matt Figler (914) 715-8954
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11728191March 31, 2026
ENGINE, SUSPENSION, POWER TRAIN
The contact owns a 2014 BMW I3. The contact stated that while driving at 49 MPH, the vehicle made an abnormal screeching sound and was leaning on the driver's side rear-end. The vehicle was taken to an independent mechanic, where a rear-end inspection was performed, and the contact was informed that no failure was found. The vehicle was not diagnosed or repaired. The contact related the failure to an unknown engine mount bracket recall. The manufacturer was notified of the failure, but no assistance was provided. The failure mileage was approximately 154,140.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11727315March 26, 2026
UNKNOWN OR OTHER
After purchasing this car used, I signed up for MyBMW remote services. My account portal stated Emergency SOS call button and crash detection services were active on my car. I decided to test, and it turns out it's not, due to the issue in SIB 84 09 22. The car will just receive a call failed message, since it's trying to do voice calls in 3G, due to the improperly programmed 4G telematics unit. So BMW knows with 100% certainty this feature will not work on the car, and the car gives no advance warning in is inoperable. Yet they are still informing me in the portal that it is active. I feel if the system is inoperable without any warning, a service bulletin without a recall is not enough. How would I have known of this issue if I didn't test it myself?
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11721513March 2, 2026
POWER TRAIN
BMW Service Bulletin SI B22 04 15 to replace motor mount bolts and other components due to failure in 2016 was done on my vehicle in 2016. BMW has replaced all motor mounts in 2014 and 2015 i3's in Europe. The motor mounts were redesigned for 2016 and newer models. From online forums I see that many of the 2014 and 2015 North American i3 motor mounts continue to fail as they have on my BMW i3. I am reporting this failure in order for NHTSA to review this vehicle for a recall on motor mounts for all 2014 and 2015 USA BMW i3's.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11713691January 27, 2026
STRUCTURE:BODY
The roof is delaminating causing a danger to my vehicle and others
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11711282January 15, 2026
POWER TRAIN, FUEL/PROPULSION SYSTEM, ELECTRICAL SYSTEM
While driving my 2016 BMW i3 with Range Extender, the vehicle experiences sudden and complete loss of propulsion at very low state of charge (0–1%). The car abruptly loses motive power, forcing me to pull over, sometimes while in traffic. After sitting for several minutes, limited power may return, but the vehicle often shuts down again, and in some cases the Range Extender engine does not engage at all. This has occurred repeatedly and creates a serious risk of being stranded or hit while merging or driving on public roads. BMW has inspected the vehicle twice (07 Nov 2025 and 13 Jan 2026) and confirmed the loss of propulsion and need to pull over but classified the behavior as “normal” without performing high-voltage battery diagnostics. The failure appears consistent with high-voltage battery voltage collapse under load, causing the battery management system to shut down the drivetrain. This is not normal power limiting — it is a sudden drivetrain shutdown that occurs without warning and poses a significant safety hazard.
Crash:
No
Fire:
No
Injuries:
0
Deaths:
0
#11705719December 17, 2025
AIR BAGS, SEAT BELTS
Summary On September 30, 2025, the passenger in a 2017 BMW i3 REX was involved in a severe frontal collision with a Gas Company Utility Vehicle. The impact struck the driver’s side extending toward the passenger side, causing the vehicle to spin violently and nearly flip. The passenger reports seatbelt failure with excessive slack, leading to partial ejection from the seat, mid-thigh restraint, and collision with the steering wheel. The head lodged under the steering column, resulting in loss of consciousness and a severe traumatic brain injury (TBI) with ongoing neurological issues. Only the driver’s curtain and seat airbags deployed; the steering wheel and passenger frontal airbags did not. Seatbelt Failure Analysis Seatbelts in modern vehicles like the BMW i3 include retractors and pretensioners designed to lock and tighten upon impact detection via accelerometers. Excessive slack, as described, suggests a malfunction in the pretensioner system, which failed to eliminate belt looseness during the high-G force event. This allowed forward momentum to propel the occupant, exacerbating injuries. Common issues in BMW i3 models include seatbelt twisting and retractor malfunctions, as reported in owner forums and repair services. Pretensioner failures can stem from sensor errors, mechanical wear, or manufacturing defects. In this crash’s severity, proper function should have secured the occupant, preventing ejection and secondary impacts. Airbag Failure Analysis The BMW employs a supplemental restraint system (SRS) with frontal, side, curtain, and seat airbags, triggered by crash sensors evaluating impact direction and force. Non-deployment of the passenger frontal and steering wheel airbags in a near-head-on collision indicates potential system failure. Possible causes include faulty occupant classification system (OCS) mats that misdetect presence/weight, leading to deactivation; sensor malfunctions; or wiring issues. A 2017 NHTSA recall (17V-720).
Crash:
Yes
Fire:
No
Injuries:
2
Deaths:
0

← Back to BMW i3