BMW ActiveHybrid 3 Service Bulletins
601 manufacturer communications on file.
- May 1, 2015•Document ID: 10147127Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B111614
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard."
Associated Products (56)Associated Documents - May 1, 2015•Document ID: 10147125Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B110815
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryN63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. ? B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs ? B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints ? B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity ? B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. ? Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine ? Excessive engine oil consumption ? Spark plugs fouled with engine oil
Associated Products (91)Associated Documents - April 6, 2015•Document ID: 10193495Service Bulletin/Repair InstructionsVISIBILITY
- Mfr Comm. #:
- B510415
- Date Added:
- May 17, 2021
- Manufacturer:
- BMW
SummaryThe customer complains of rattling noises from the rear window when driving on rough roads.
Associated Products (50)Associated Documents - April 1, 2015•Document ID: 10152317Service Bulletin/Repair InstructionsBACK OVER PREVENTION
- Mfr Comm. #:
- B660115
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
SummarySurround View Camera Last User Mode Operation Change. After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear is selected, the default view will be the rear camera. The surround/top camera view has been removed from the last user mode function. This is to meet the upcoming (new) federal regulations regarding rear view cameras. Note: The surround/top camera view is available, but the driver must manually switch the camera view using the iDrive controller.
Associated Products (130)Associated Documents - April 1, 2015•Document ID: 10152306Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- B130315
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
Summary"N20 and N26 Engines: ETK Injector Part Number Error. INFORMATION The current version of ETK has an error on screen 13_1417: ""High -pressure pump/Tubing."" When selecting the high-pressure pump, the screen states ""only in conjunction with injector."" Disregard this statement and only replace the high-pressure pump. If injectors need to be replaced, enter the VIN of the vehicle into the ETK and select the part numbers found on screen 13_1416: ""High-pressure rail/injector/mounting."" Always enter the VIN for the vehicle into ETK when searching for parts. When the ETK is corrected, this SIB will be updated. WARRANTY INFORMATION Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/224...5/4/2015"
Associated Products (79)Associated Documents - April 1, 2015•Document ID: 10152305Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B122114
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
SummaryEngine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
Associated Products (76)Associated Documents - March 1, 2015•Document ID: 10147690Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- B840514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryOne or both of the situations listed below may be encountered: ? Android device connection stability (dropped calls) ? Third-Party App Metadata: The album art and song title do not update when streaming audio from Pandora or Spotify, etc. New KISU (Customer Initiated Software Update) software is available on the TIS website. This software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation.
Associated Products (150)Associated Documents - March 1, 2015•Document ID: 10147689Service Bulletin/Repair InstructionsVEHICLE SPEED CONTROL:CRUISE CONTROL
- Mfr Comm. #:
- B660215
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Remote Control Not Detected and/or Engine Will Not Start. One or more of the following situations can occur: 1. The remote control is not detected and the check control message (CCM) ""No remote control. Unable to start"" or ""Hold the remote control on the steering column"" is displayed. ? Fault code ""D90D1E - LIN bus error FBD receiver 1"" is stored. 2. The engine does not start with the CCM with ""Battery in the key is dead."" However, it must work when used with the second key. ? Fault Code ""9308B0 - ID transmitter: Battery undervoltage"" is stored. 3. The remote control is not detected and the CCM ""Central locking does not open,"" and/or ""Engine fails to start"" is displayed. An outside influence is causing interference with the remote control or the battery in the remote control key is defective."
Associated Products (34)Associated Documents - March 1, 2015•Document ID: 10147686Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS
- Mfr Comm. #:
- B630315
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Halogen Headlight Side Bulbs Fail. The check control message (CCM) ""Parking lamp malfunction: Consult service center"" is displayed when the vehicle is started. Defective side light bulb on one or both sides"
Associated Products (16)Associated Documents - March 1, 2015•Document ID: 10147682Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; ELECTRICAL SYSTEM:HORN; VISIBILITY:REAR WINDOW WIPER/WASHER
- Mfr Comm. #:
- B610415
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHorn Blows when Unlocking Vehicle. The customer states that the vehicle horn sounds briefly when unlocking the vehicle or opening the door. In some cases, the washers spray briefly on the windshield. Front Electronics Module (FEM) software error
Associated Products (32)Associated Documents - March 1, 2015•Document ID: 10147678Service Bulletin/Repair InstructionsSTRUCTURE:BODY:HOOD
- Mfr Comm. #:
- B511112
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryBody Equipment March 2015 Technical Service. This Service Information bulletin supersedes SI B51 11 12 dated March 2012. designates changes to this revision SUBJECT Engine Hood Does Not Open Properly. The engine hood cannot be opened or it is only unlocking on one side. Note: The hood can be opened if the hood release lever is activated by one person while another person pulls upward on the hood at the same time. CAUSE Incorrect adjustment of the hood strikers.
Associated Products (6)Associated Documents - March 1, 2015•Document ID: 10147676Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT
- Mfr Comm. #:
- B510315
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Front Floor Mats Do Not Stay in Place. The Velcro patch attached to the bottom of the floor mat peels off. Poor adhesion of the Velcro patch Thank you for all the PuMA ""Info Only"" cases. From these cases, it has been determined that the Velcro peeling fault occurs on mats produced prior to May 2014. We no longer need ""Info Only"" cases from this time period."
Associated Products (28)Associated Documents - March 1, 2015•Document ID: 10147672Service Bulletin/Repair InstructionsSERVICE BRAKES
- Mfr Comm. #:
- B340215
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. SUBJECT Service Action: Program Control Units (DSC). In very rare driving situations (distances of more than 310 miles travelled without any DSC, ABS or cruise control/ACC regulation), the DSC return pump is activated in order to initiate internal flushing. When this occurs, it is possible that the pump is not switched off until the engine is turned off. VEHICLES AFFECTED This Service Action involves certain ActiveHybrid models produced from 8/6/2013 to 1/27/2015. First check if a Service Action label with a code number 739 is already attached to the B-pillar. If a code number 739 has been punched out, the Campaign has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader."
Associated Products (4)Associated Documents - March 1, 2015•Document ID: 10147667Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING; ENGINE
- Mfr Comm. #:
- B123314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryFault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
Associated Products (42)Associated Documents - March 1, 2015•Document ID: 10147663Service Bulletin/Repair InstructionsENGINE; ELECTRICAL SYSTEM
- Mfr Comm. #:
- B121415
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"DME Fault Code CD9711 Stored After Programming. After programming the vehicle with ISTA/P 3.55.0 (I-Level F010-15-03-501 and F001-15-03-501): ? The check engine light (CEL) is illuminated, and ? DME fault code ""CD9711 - FlexRay, message (control diagnostics OBD vehicle dynamics, 247.0.2): missing"" is stored and cannot be cleared. CAUSE DME software"
Associated Products (4)Associated Documents - March 1, 2015•Document ID: 10147656Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B111614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard. AFFECTED VEHICLES This Service Action applies to E70, E71, E72, F01, F02, F04, F07, F10, F12, and F13 vehicles with the N63 engines corresponding to the production dates listed above. First check if a Service Action label with a code number 728 is already attached to the B-pillar. If a code number 728 has already been punched out, the Campaign has already been performed and no further action is necessary. Eligible vehicles will show the following Service Action-related Campaign Code: 00 13 48 02 00 If the vehicle already has a label from a previous Service Action/Recall Campaign, affix the new label next to the old one. Do not affix one label on top of another one, because a number from an underlying label could appear in the punched-out hole of the new label."
Associated Products (65)Associated Documents - March 1, 2015•Document ID: 10147655Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B110715
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"N63: Quality Control Monitoring After CCP. INFORMATION If the vehicle exhibits any of the above drivability issues, perform the ISTA/D N63 Misfire Detection test plan. Please make sure the FASTA data is transmitted. Submit a PuMA case titled ""N63: Drivability after CCP."" Follow the recommendations received."
Associated Products (56)Associated Documents - March 1, 2015•Document ID: 10147653Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B110515
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"N20 and N55 Engine: Engine Oil Filter Application for Plastic Oil Filter Housing. The current version of EPC does not provide all available options for the engine oil filters used in the N20 and N55 engines produced with a ""plastic"" oil filter housing. The illustration below will help identify the proper engine oil filter application until the EPC is corrected."
Associated Products (26)Associated Documents - March 1, 2015•Document ID: 10147652Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B110315
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN20 and N26 Engine: Oil Leaks from Cylinder Head Cover. There is an engine oil leakage under the vehicle, or the vehicle smells of engine oil. The cylinder head cover gasket is leaking engine oil due to loose retaining bolt(s).
Associated Products (79)Associated Documents - February 1, 2015•Document ID: 10147091Service Bulletin/Repair InstructionsAIR BAGS
- Mfr Comm. #:
- 650414
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"Airbag Warning Light: ACSM FC 930A60 or 930A1C Seat Occupancy Detection. According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. 1. ACSM fault code ""930A60 - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. Or 2. ACSM fault code ""930A1C - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. CAUSE The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself."
Associated Products (117)Associated Documents