BMW 428i Service Bulletins
457 manufacturer communications on file.
- May 1, 2014•Document ID: 10148321Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT
- Mfr Comm. #:
- 510514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryMF56 Make Good Program: Install Accessory Roof Graphic or Mirror Caps. Due to production restrictions at Plant Oxford, certain F56 vehicles produced in May and June of this year cannot be built with the factory option for the contrasting roof and/or mirror caps. This production issue was caused by the plant expanding its paint capabilities to meet increasing vehicle demand. In a continuing effort to maintain the utmost in Motorer satisfaction, MINI USA is offering our dealer partners an alternative solution, the "Make Good" program. For all affected MINI F56 vehicles: * Produced from May 1, 2014 to June 30, 2014 and * Built without the factory order "Contrasting Roof and Mirror Caps" option (382 and 383) Your MINI dealer can offer these Motorers the installation of an accessory roof graphic or set of mirror caps. The Motorer has the choice of either the accessory roof graphic or exterior mirror caps, not both. MINI Area Manager (AM) "Field Authorization" (FAS) is not required. Note: For eligible vehicles (VINs) that are affected by this production restriction, the procedure outlined in this bulletin only applies to mirror caps or roof graphics installed by your dealer. Mirror caps or roof graphics installed through the MINI USA "VIA" (VDC-Installed Accessory) program are not eligible for reimbursement through this Make Good Program.
Associated Products (20)Associated Documents - May 1, 2014•Document ID: 10148310Service Bulletin/Repair InstructionsPOWER TRAIN; ENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 170114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryLow Coolant Level with No Sign of External Leaks. The Low Coolant Warning light is on and there are no signs of a visual leak. Pressure testing the cooling system may or may not show an internal leak (loss of pressure). There may also be a complaint of transmission fluid leaking from the vent on top of the transmission; poor shift quality; or a shuddering from the transmission. There is an internal failure of the automatic transmission oil cooler, allowing coolant to mix with transmission fluid. Possible faulty coolers were built between 6/6/2013 and 8/4/2013.
Associated Products (11)Associated Documents - April 1, 2014•Document ID: 10148276Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- 650514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryTraffic Information Is Inoperative. The traffic information is intermittently or permanently inoperative. * Traffic flow is not displayed on the navigation map. * The traffic list is empty. 1. The Offboard Availability (backend) system is unavailable and is not sending traffic information. 2. The traffic information feature is not activated correctly.
Associated Products (209)Associated Documents - April 1, 2014•Document ID: 10148273Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 610314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCheck Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
Associated Products (242)Associated Documents - April 1, 2014•Document ID: 10148270Service Bulletin/Repair InstructionsEQUIPMENT; STRUCTURE:BODY:DOOR
- Mfr Comm. #:
- 511014
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryFront Door Loudspeaker Make Noises When Cold. The customer complains of front door loudspeaker noises when the temperature is below freezing. CAUSE Water from the door window may enter the rear area of the front door medium range loudspeaker basket/cage and can solidify when the temperature drops below freezing, creating the noise.
Associated Products (24)Associated Documents - April 1, 2014•Document ID: 10148266Service Bulletin/Repair InstructionsSTRUCTURE:FRAME AND MEMBERS
- Mfr Comm. #:
- 410114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Repair Right Side Panel Corrosion Protection. The right side panel corrosion protection is not sufficient. The sheet metal plate clearance in the right side A-pillar area is too small for complete corrosion protection from the factory.
Associated Products (4)Associated Documents - March 1, 2014•Document ID: 10148010Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 840114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryConnectedDrive/BMW Assist System Information and Availability. ConnectedDrive features are partially or completely inoperative. Examples of some of these features are listed below: * BMW Assist Inoperative ? SOS call ? Roadside Assistance call * My BMW Remote App * BMW Online - Google local search * Concierge CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availabilty (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle.
Associated Products (211)Associated Documents - March 1, 2014•Document ID: 10147927Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING; EQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- 640613
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryA/C Cooling: Intermittent Reduction of Air Flow. The customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than one hour. The complaint can vary due to one or more of the following variables: * High outside ambient temperature * Too much humidity * A/C temperature and fan settings set too low for too long Note: It is very difficult to duplicate this issue due the required outdoor weather conditions and length of driving time needed. CAUSE Evaporator starts to freeze up due to the position of the evaporator temperature sensor
Associated Products (13)Associated Documents - March 1, 2014•Document ID: 10147925Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS
- Mfr Comm. #:
- 630814
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryActive Headlight Control Malfunction in Both Headlights. AHL (Active Headlight Control) malfunctions on both sides. Both lights aim either up or down while driving. CAUSE Broken mounting bolt holding on the rear height sensor bracket
Associated Products (20)Associated Documents - March 1, 2014•Document ID: 10147920Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- 330114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"?SI B33 01 14 March 2014 Rear AxleTechnical Service. This Service Information bulletin supersedes SI B33 01 14 dated February 2014. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. designates changes to this revision SUBJECT Delivery Stop/Service Action: Check Rear Axle Differential. 1 A Delivery Stop has been issued on certain 2014 model year F15 and F3x vehicles produced from July 2013 to January 2014 because the final drive differential gears may not have been properly hardened. Vehicles held at the ports of entry are being inspected and/or repaired prior to center delivery. During this inspection and analysis of data, BMW of North America has documented a failure rate of less than one in two hundred. The affected vehicles are listed in the attachment to this bulletin; they are also identified with a ""Vehicle Comment"" in the DCSnet Warranty Vehicle Inquiry or ISPA as follows: ??Defect Code 0033840100, Delivery Stop: Rear Axle Differential; see SI B 33 01 14 The initial limited available stock of parts is reserved for vehicles that have already been sold and are in customers' hands (see Situation 2). Affected vehicles in center inventory must not be retailed or delivered until the rear differential has been replaced. 2 Certain 2014 model year F15 and F3x vehicles produced from July 2013 to January 2014 may have final drive differential gears that have not been properly hardened. These vehicles have already been sold and delivered to customers."
Associated Products (8)Associated Documents - February 1, 2014•Document ID: 10147984Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- 840613
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryiPhone Charging Status Constantly Switches On and Off. INFORMATION Do not replace any other parts! Advise the customer that he/she must use one of the following: * The original Apple iPhone/iPOD USB cable that came with the device * A BMW supplied iPhone/iPOD USB adapter cable PARTS INFORMATION
Associated Products (94)Associated Documents - February 1, 2014•Document ID: 10147982Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- 652313
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHeadunit-High: Navigation Road Map Installation After Replacement. When replacing the HU-H, the road map database version that was in the defective HU-H must be installed in the new HU-H.
Associated Products (98)Associated Documents - February 1, 2014•Document ID: 10147980Service Bulletin/Repair InstructionsVISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:FAN/MOTOR; ENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 640713
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Replace Blower Motor Regulator. The blower motor regulator has an internal fault; after starting the engine, there may be a delay of up to a minute before the blower motor comes on CAUSE Faulty blower motor regulator (output stage)
Associated Products (20)Associated Documents - February 1, 2014•Document ID: 10147979Service Bulletin/Repair InstructionsVISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- 640114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryNoise from Heating and Air Conditioner. There is an intermittent whirring noise from the IHKA system when the engine is under load between 2,000 and 3,000 rpm, and sometimes at approximately 5,000 rpm. CAUSE Vibrations from the A/C low-pressure hose are resonating into the heating and air conditioning system.
Associated Products (11)Associated Documents - February 1, 2014•Document ID: 10147978Service Bulletin/Repair InstructionsEQUIPMENT; EXTERIOR LIGHTING:HEADLIGHTS
- Mfr Comm. #:
- 630614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryOne or Both Headlights Are Aimed Downwards. The customer may experience one or more of the following complaints: * One or both headlights are aimed significantly too low (jammed lower limit). * No reference run is visible on the affected headlight when the ignition is turned on and the light switch is in the auto position. * No CCM (Check Control Message) is displayed when a headlight is faulty. CAUSE * TMS-3 (Headlight driver module AHL) coding error * Defective mechanism inside the headlight
Associated Products (3)Associated Documents - February 1, 2014•Document ID: 10147974Service Bulletin/Repair InstructionsVISIBILITY:SUN/MOON ROOF ASSEMBLY
- Mfr Comm. #:
- 540213
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary?Sunroof Gets Stuck or Moves in Small Steps. During opening or closing the sunroof, one or more of the following situations may occur: 1. The sunroof becomes stuck 2. One-touch open and close no longer works 3. The sunroof moves in small steps. CAUSE Software error in the sunroof control module (FZD) Some or all of the following fault codes may be stored: 0x030212 - SHD: Activation timeout, no block recognition 0x030214 - SHD: Zero position passed, loss of calibration 0x030215 - SHD: Invalid characteristic curve, not normalized 0x030216 - SHD: 90% motor temperature threshold exceeded 0x030217 - SHD: Motor operation interrupted by overheating 0x030218 - SHD: Motor does not start due to overvoltage or undervoltage 0x030219 - SHD: Errors in the checksum coding 0x03021C - SHD: Not initialized due to invalid marginal conditions (motor driver) 0x030220 - SHD: System not normalized 0x801A02 - Coding: Control unit is not coded.
Associated Products (13)Associated Documents - February 1, 2014•Document ID: 10147973Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; VISIBILITY
- Mfr Comm. #:
- 510714
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryNoise from Rearview Mirror. Rattling noises can be heard from the rearview mirror when driving. CAUSE The mirror electrical connector is loose in the mirror base.
Associated Products (20)Associated Documents - February 1, 2014•Document ID: 10147972Service Bulletin/Repair InstructionsEQUIPMENT; STRUCTURE
- Mfr Comm. #:
- 510514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Remove and Discard Water Drain Plugs from E-Box. Water leaks into the cabin due to clogged drain plugs in the E-boxes. CAUSE The drain plug slots are too small and clog.
Associated Products (20)Associated Documents - February 1, 2014•Document ID: 10147967Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING; ENGINE
- Mfr Comm. #:
- 122513
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryReduced Engine and Air-Conditioning Performance. When driving with high outside ambient temperatures, repeated stop and go, or high load operation over longer distances, the engine performance can be reduced. The air-conditioning system blower output may also be reduced, and in some circumstances the compressor is switched off. There could be any of the following faults stored depending on the conditions present at the time. DME * Fault 1A2108: Electric fan, self-diagnosis, interval stage 1: Minor fan fault EGS (also possibly set) * Fault 421722: DME/DDE interface: Forced upshift due to thermal engine protection request IHKA (possibly set without DME or EGS faults) * Fault 801224: Air conditioning compressor: Shut-down due to excess pressure in refrigerant circuit * Fault 801228: Blower output stage: Blower output reduction due to power management The Service Engine Soon lamp (MIL) would not be illuminated in these situations. 1. A DME software error in the control of the 850W electric fan over-boost or high speed function. 2. The electric cooling fan design was not robust enough for continuous over-boost or high speed operation.
Associated Products (12)Associated Documents - January 1, 2014•Document ID: 10147954Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT
- Mfr Comm. #:
- 653009
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryEnabling Code FSC/SWT - Enabling the Navigation System Map at QC1. The navigation system is inoperative unless the map is enabled during the QC1 Pre-Delivery Check. INFORMATION New vehicles come equipped with a navigation road map that must be enabled via an enable code (FSC). This process is part of the QC1 Pre-Delivery Check performed with the ISID (ISTA Diagnosis). IMPORTANT: There is no programming involved!
Associated Products (119)Associated Documents